scholarly journals VARIATION OF ELECTRIC PROPERTIES BETWEEN SURFACE PERMANENT MAGNET AND INTERIOR PERMANENT MAGNET MOTOR

2012 ◽  
Vol 06 ◽  
pp. 109-114
Author(s):  
BYUNG-CHUL WOO ◽  
DO-KWAN HONG ◽  
JI-YOUNG LEE
Keyword(s):  
Permanent Magnet ◽  
Complex Geometry ◽  
Torque Ripple ◽  
Direct Drive ◽  
Element Analysis ◽  
Torque Density ◽  
Interior Permanent Magnet ◽  
3D Fea ◽  
High Torque ◽  
Transverse Flux

The most distinctive advantage of transverse flux motor(TFM) is high torque density which has prompted many researches into studying various design variants. TFM is well suited for low speed direct drive applications due to its high torque density. This paper deals with simulation based comparisons between a surface permanent magnet transverse flux motor(SPM-TFM) and an interior permanent magnet transverse flux motor(IPM-TFM). A commercial finite element analysis(FEA) software Maxwell 3D is used for electromagnetic field computation to fully analyze complex geometry of the TFMs. General characteristics, such as cogging torque, rated torque and torque ripple characteristics of the two TFMs are analyzed and compared by extensive 3D FEA.

scholarly journals Design and Analysis of a Novel Axial-Radial Flux Permanent Magnet Machine with Halbach-Array Permanent Magnets

Energies ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3639
Author(s):  
Rundong Huang ◽  
Chunhua Liu ◽  
Zaixin Song ◽  
Hang Zhao
Keyword(s):  
Permanent Magnet ◽  
Permanent Magnets ◽  
Torque Ripple ◽  
Axial Flux ◽  
Element Analysis ◽  
Torque Density ◽  
Axial Forces ◽  
Halbach Array ◽  
Radial Flux ◽  
High Torque

Electric machines with high torque density are needed in many applications, such as electric vehicles, electric robotics, electric ships, electric aircraft, etc. and they can avoid planetary gears thus reducing manufacturing costs. This paper presents a novel axial-radial flux permanent magnet (ARFPM) machine with high torque density. The proposed ARFPM machine integrates both axial-flux and radial-flux machine topologies in a compact space, which effectively improves the copper utilization of the machine. First, the radial rotor can balance the large axial forces on axial rotors and prevent them from deforming due to the forces. On the other hand, the machine adopts Halbach-array permanent magnets (PMs) on the rotors to suppress air-gap flux density harmonics. Also, the Halbach-array PMs can reduce the total attracted force on axial rotors. The operational principle of the ARFPM machine was investigated and analyzed. Then, 3D finite-element analysis (FEA) was conducted to show the merits of the ARFPM machine. Demonstration results with different parameters are compared to obtain an optimal structure. These indicated that the proposed ARFPM machine with Halbach-array PMs can achieve a more sinusoidal back electromotive force (EMF). In addition, a comparative analysis was conducted for the proposed ARFPM machine. The machine was compared with a conventional axial-flux permanent magnet (AFPM) machine and a radial-flux permanent magnet (RFPM) machine based on the same dimensions. This showed that the proposed ARFPM machine had the highest torque density and relatively small torque ripple.

Study and design of dual stator permanent magnet machine with spoke-type configurations using phase-group concentrated-coil windings

2020 ◽  
Vol 64 (1-4) ◽  
pp. 1381-1389
Author(s):  
Dezhi Chen ◽  
Chengwu Diao ◽  
Zhiyu Feng ◽  
Shichong Zhang ◽  
Wenliang Zhao
Keyword(s):  
Permanent Magnet ◽  
Permanent Magnets ◽  
Low Cost ◽  
Dynamic Performance ◽  
Torque Ripple ◽  
Permanent Magnet Machine ◽  
Torque Density ◽  
Phase Group ◽  
High Torque ◽  
Simulation Results

In this paper, a novel dual-stator permanent magnet machine (DsPmSynM) with low cost and high torque density is designed. The winding part of the DsPmSynM adopts phase-group concentrated-coil windings, and the permanent magnets are arranged by spoke-type. Firstly, the winding structure reduces the amount of copper at the end of the winding. Secondly, the electromagnetic torque ripple of DsPmSynM is suppressed by reducing the cogging torque. Furthermore, the dynamic performance of DsPmSynM is studied. Finally, the experimental results are compared with the simulation results.

scholarly journals Improvement in Torque Density by Ferrofluid Injection into Magnet Tolerance of Interior Permanent Magnet Synchronous Motor

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1736
Author(s):  
In-Jun Yang ◽  
Si-Woo Song ◽  
Dong-Ho Kim ◽  
Kwang-Soo Kim ◽  
Won-Ho Kim
Keyword(s):  
Permanent Magnet ◽  
Electromotive Force ◽  
Permanent Magnet Synchronous Motor ◽  
Synchronous Motor ◽  
Element Analysis ◽  
Final Model ◽  
Torque Density ◽  
Leakage Path ◽  
Interior Permanent Magnet ◽  
Simulation Results

In an interior permanent magnet synchronous motor, an adhesive such as bond is generally injected into the magnet tolerance to prevent vibration of the permanent magnet within the insertion space. In this case, a disadvantage is that the magnet tolerance does not contribute to the performance. In this paper, ferrofluid is inserted to improve the torque density, utilizing the magnet tolerance. When inserting ferrofluid into the magnet tolerance, it is important to fix the magnet because conventional adhesives are not used, and it is important that the ferrofluid does not act as a leakage path within the insertion space. In this study, a new rotor configuration using a plastic barrier that satisfies these considerations was introduced. The analysis was conducted through finite element analysis (FEA), and this technique was verified by comparing the simulation results and the experimental results through a dynamo test. It was confirmed that the no-load back electromotive force in the final model increased through ferrofluid injection.

Torque imporvement of IPM motors with skewing magnetic designs

2021 ◽  
pp. 3-10
Author(s):  
Dinh Hai Linh
Keyword(s):  
Permanent Magnet ◽  
High Speed ◽  
Torque Ripple ◽  
Maintenance Cost ◽  
Permanent Magnet Motor ◽  
Element Analysis ◽  
Speed Range ◽  
Interior Permanent Magnet ◽  
Interior Permanent Magnet Motor ◽  
Wide Speed Range

In this paper, a type interior permanent magnet synchronous motor designs is proposed for sport scooter application to improve constant torque wide speed performance. Interior Permanent Magnet machines are widely used in automotive applications for their wide-speed range operation and low maintenance cost. An existing permanent magnet motor (commercial QS Motor) is 3 kW-3000 rpm. In order to improve torque and power in wide speed range, a IPM electric motor 5.5 kW -5000 rpm can run up to 100 km/h: An Step-Skewing Interior Permanent Magnet motor alternatives is designed and optimized in detail with optimal magnetic segment V shape. The electromagnetic charateristics of Interior Permanent Magnet motors with V shape are compared with the reference Surface Permanent Magnet motor for the same geometry parameter requirements. Detailed loss and efficiency result is also analyzed at rate and maximum speeds. A prototype motor is manufactured, and initial experimental tests are performed. Detailed comparison between Finite Element Analysis and test data are also presented. It is shown that it is possible to have an optimized Interior Permanent Magnet motor for such high-speed traction application. This paper will figure out optimal angle of magnetic V shape for maximum torque and minimum torque ripple.

scholarly journals Performances analysis of interior permanent magnet motors having different rotor iron pole shapes

2021 ◽  
Vol 12 (4) ◽  
pp. 1999
Author(s):  
Ahlam Luaibi Shuraiji ◽  
Buraq Abdulhadi Awad
Keyword(s):  
Permanent Magnet ◽  
Torque Ripple ◽  
High Energy ◽  
Electromagnetic Torque ◽  
Permanent Magnet Motors ◽  
Element Analysis ◽  
Magnet Material ◽  
Interior Permanent Magnet ◽  
Rotor Pole ◽  
Permanent Magnet Material

<p><span lang="EN-US">Interior permanent magnet motors (IPMMs) have been increasing in popularity, since the emergence of permanent magnet material with high energy products, i.e. rare earth permanent magnet material. This paper analyses the performances of IPMMs having different rotor iron pole shapes including eccentric, sinusoidal and sinusoidal with 3th order harmonic injected rotor pole arc shapes IPMMs. Cogging torque, static torque, torque ripple, torque-speed and power-speed curves of the mentioned motors have been compared. It must be noted that the mentioned motors have been designed with the same stator, PM shape and the same dimensions, in order to highlight the effect of the rotor pole arc shape on the performance of the such motors. Two-dimensional (2D) finite element analysis (FEA) has been utilized to design and analyze the mentioned machines. It has been found that rotor iron pole shape of the IPM has notably influence on the machine performance, practically on output electromagnetic torque and its ripple. The highest value of average electromagnetic torque as well as torque capability in the constant torque reign is delivered by 3th order harmonic injected rotor pole arc shapes machine, while the lowest torque ripple is obtained by the sinusoidal rotor pole arc machine.</span></p>

scholarly journals Investigation of a New Flux-Modulated Permanent Magnet Brushless Motor for EVs

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Ying Fan ◽  
Lingling Gu ◽  
Yong Luo ◽  
Xuedong Han ◽  
Ming Cheng
Keyword(s):  
High Speed ◽  
Simple Structure ◽  
Static Characteristics ◽  
Direct Drive ◽  
Element Analysis ◽  
Torque Density ◽  
Brushless Motor ◽  
Design Requirements ◽  
High Torque ◽  
Compact Design

This paper presents a flux-modulated direct drive (FMDD) motor. The key is to integrate the magnetic gear with the PM motor while removing the gear inner-rotor. Hence, the proposed FMDD motor can achieve the low-speed high-torque output and high-speed compact design requirements as well as high-torque density with a simple structure. The output power equation is analytically derived. By using finite element analysis (FEA), the static characteristics of the proposed motor are obtained. Based on these characteristics, the system mathematical model can be established. Hence, the evaluation of system performances is conducted by computer simulation using the Matlab/Simulink. A prototype is designed and built for experimentation. Experimental results are given to verify the theoretical analysis and simulation.

scholarly journals Design and Analysis of Outer Rotor Permanent-Magnet Vernier Machines with Overhang Structure for In-Wheel Direct-Drive Application

Energies ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1238 ◽  
Author(s):  
Dong Yu ◽  
Xiaoyan Huang ◽  
Lijian Wu ◽  
Youtong Fang
Keyword(s):  
Permanent Magnet ◽  
Magnetic Composite ◽  
Direct Drive ◽  
Soft Magnetic ◽  
Axial Flux ◽  
Element Analysis ◽  
Torque Density ◽  
Outer Rotor ◽  
Flux Modulation ◽  
Conventional Machine

This paper presents a novel outer rotor permanent-magnet vernier machine (PMVM) for in-wheel direct-drive application. The overhang structures of the rotor and flux modulation pole (FMP) are introduced. The soft magnetic composite (SMC) was adopted in the FMP overhang to allow more axial flux. The 3-D finite element analysis (FEA) was carried out to prove that the proposed machine can effectively utilize the end winding space to enhance the air-gap flux density. Hence the PMVM can offer 27.3% and 14.5% higher torque density than the conventional machine with no overhang structure and the machine with only rotor overhang structure, respectively. Nevertheless, the efficiency of the proposed machine is slightly lower than the conventional ones due to the extra losses from the overhang structures.

Sign in / Sign up

Export Citation Format

Share Document