Localized-Field Permanent Magnet Array for the Thick-Film Read Only Store

1966 ◽  
Vol 10 (4) ◽  
pp. 343-345 ◽  
Author(s):  
C. Johnson ◽  
R. C. Turnbull
Keyword(s):  
Permanent Magnet ◽  
Thick Film

Electrical Properties of Superconductive Thick Film Wires Obtained from a Melt Process

2021 ◽  
Vol 21 (9) ◽  
pp. 4944-4948
Author(s):  
Sang Heon Lee
Keyword(s):  
Magnetic Field ◽  
Transition Temperature ◽  
Electrical Properties ◽  
Critical Current Density ◽  
Permanent Magnet ◽  
Thick Film ◽  
Magnetic Force ◽  
Raw Materials ◽  
Surface Magnetism ◽  
Magnetic Cooling

YBaCuO superconductive thick film wires were fabricated by employing a melt process with a peak temperature of 1100 °C. Transition temperature and peak critical current density of these YBaCuO superconductive thick film wires were 90 K and 3.5 × 104 A/cm2, respectively. Their magnetic lev-itation force measured at a temperature of 77 K with a permanent magnet was 65.45 N during magnetic cooling. The repulsion force in the case of field cooling was 10.12 N. A permanent magnet with surface magnetism of 5.25 kG was used to cool down superconductive specimens, from which magnetic force of 15.62% of peak magnetic field was trapped. A single crystal YBaCuO superconductive thick film wire was obtained after coating powders of raw materials from a melt process employed for the fabrication of YBaCuO superconductive thick film wire.

Scanning Electron Microscopy in Hybrid Microelectronics

1976 ◽  
Vol 34 ◽  
pp. 456-457
Author(s):  
S. Khadpe ◽  
R. Faryniak
Keyword(s):  
Integrated Circuits ◽  
Thick Film ◽  
Integrated Circuit ◽  
Failure Modes ◽  
Three Dimensional ◽  
Circuit Components ◽  
Hybrid Microcircuit ◽  
Electrical Connections ◽  
Scanning Electron

The Scanning Electron Microscope (SEM) is an important tool in Thick Film Hybrid Microcircuits Manufacturing because of its large depth of focus and three dimensional capability. This paper discusses some of the important areas in which the SEM is used to monitor process control and component failure modes during the various stages of manufacture of a typical hybrid microcircuit.Figure 1 shows a thick film hybrid microcircuit used in a Motorola Paging Receiver. The circuit consists of thick film resistors and conductors screened and fired on a ceramic (aluminum oxide) substrate. Two integrated circuit dice are bonded to the conductors by means of conductive epoxy and electrical connections from each integrated circuit to the substrate are made by ultrasonically bonding 1 mil aluminum wires from the die pads to appropriate conductor pads on the substrate. In addition to the integrated circuits and the resistors, the circuit includes seven chip capacitors soldered onto the substrate. Some of the important considerations involved in the selection and reliability aspects of the hybrid circuit components are: (a) the quality of the substrate; (b) the surface structure of the thick film conductors; (c) the metallization characteristics of the integrated circuit; and (d) the quality of the wire bond interconnections.

NEW PERMANENT MAGNET DEVICES

1984 ◽  
Vol 45 (C1) ◽  
pp. C1-285-C1-291 ◽  
Author(s):  
R. Pauthenet
Keyword(s):  
Permanent Magnet

A novel analytical calculation of magnetic field in the slotted air gap of spoke-type permanent-magnet machines using conformal mapping

2020 ◽  
pp. 1-15
Author(s):  
Jianqi Li ◽  
Yu Zhou ◽  
Jianying Li
Keyword(s):  
Magnetic Field ◽  
Conformal Mapping ◽  
Permanent Magnet ◽  
Flux Density ◽  
Analytical Method ◽  
Electromotive Force ◽  
Analytical Calculation ◽  
Air Gap ◽  
Permanent Magnet Machines ◽  
Peak Value

This paper presented a novel analytical method for calculating magnetic field in the slotted air gap of spoke-type permanent-magnet machines using conformal mapping. Firstly, flux density without slots and complex relative air-gap permeance of slotted air gap are derived from conformal transformation separately. Secondly, they are combined in order to obtain normalized flux density taking account into the slots effect. The finite element (FE) results confirmed the validity of the analytical method for predicting magnetic field and back electromotive force (BEMF) in the slotted air gap of spoke-type permanent-magnet machines. In comparison with FE result, the analytical solution yields higher peak value of cogging torque.

Performance analysis of magnetic gear with Halbach array for high power and high speed

2020 ◽  
Vol 64 (1-4) ◽  
pp. 959-967
Author(s):  
Se-Yeong Kim ◽  
Tae-Woo Lee ◽  
Yon-Do Chun ◽  
Do-Kwan Hong
Keyword(s):  
Permanent Magnet ◽  
Eddy Current ◽  
High Power ◽  
High Speed ◽  
Torque Ripple ◽  
Eddy Current Loss ◽  
Element Analysis ◽  
Current Loss ◽  
Halbach Array ◽  
Magnetic Gear

In this study, we propose a non-contact 80 kW, 60,000 rpm coaxial magnetic gear (CMG) model for high speed and high power applications. Two models with the same power but different radial and axial sizes were optimized using response surface methodology. Both models employed a Halbach array to increase torque. Also, an edge fillet was applied to the radial magnetized permanent magnet to reduce torque ripple, and an axial gap was applied to the permanent magnet with a radial gap to reduce eddy current loss. The models were analyzed using 2-D and 3-D finite element analysis. The torque, torque ripple and eddy current loss were compared in both models according to the materials used, including Sm2Co17, NdFeBs (N42SH, N48SH). Also, the structural stability of the pole piece structure was investigated by forced vibration analysis. Critical speed results from rotordynamics analysis are also presented.

Analysis of structure factors affecting suspension force of permanent magnet system with variable magnetic flux path control

2020 ◽  
Vol 64 (1-4) ◽  
pp. 1495-1504
Author(s):  
Fangchao Xu ◽  
Yongquan Guo ◽  
Ran Zhou ◽  
Junjie Jin ◽  
Chuan Zhao ◽  
...  
Keyword(s):  
Magnetic Flux ◽  
Permanent Magnet ◽  
System Structure ◽  
Magnet System ◽  
Load Torque ◽  
Factors Affecting ◽  
Annular Gap ◽  
Path Control ◽  
Structure Factors ◽  
Flux Path

To solve the problem of reduction of suspension force of permanent magnet system with variable magnetic flux path control, according to the structure of the system, suspension principle of the permanent magnet system with variable magnetic flux path control and the generation principle of the load torque, the influence of the mechanical structure of the system on the suspension force is analyzed by changing part of parameters of the system structure. The results show that the existence of magnetic isolation plate is the main reason for the decrease of suspension force, the permanent magnet ring can be thickened to 11.91 mm, the annular gap can be reduced to 1 mm, thickness of the “F” shaped magnetizer can be increased to 9 mm to increase the suspension force.

Sign in / Sign up

Export Citation Format

Share Document