Innovative Electrochemical Processing for Copper Removal from Carbon Saturated Iron Melt Using Na2S-FeS Molten Sulfide

2021 ◽  
Author(s):  
Zhihao Lu ◽  
Chengjun Liu ◽  
Yeguang Wang
Keyword(s):  
Copper Removal ◽  
Electrochemical Processing ◽  
Carbon Saturated Iron

scholarly journals Novel PVDF-PVP Hollow Fiber Membrane Augmented with TiO2 Nanoparticles: Preparation, Characterization and Application for Copper Removal from Leachate

Nanomaterials ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 399
Author(s):  
Mohammed Umar Abba ◽  
Hasfalina Che Man ◽  
Raba’ah Syahidah Azis ◽  
Aida Isma Idris ◽  
Muhammad Hazwan Hamzah ◽  
...  
Keyword(s):  
Contact Angle ◽  
Adsorption Capacity ◽  
Tio2 Nanoparticles ◽  
Polyvinylidene Fluoride ◽  
Negative Impact ◽  
Hollow Fiber Membrane ◽  
Copper Removal ◽  
Fiber Membrane ◽  
Copper Adsorption ◽  
Phase Inversion Technique

High proportion of copper has become a global challenge owing to its negative impact on the environment and public health complications. The present study focuses on the fabrication of a polyvinylidene fluoride (PVDF)-polyvinyl pyrrolidone (PVP) fiber membrane incorporated with varying loading (0, 0.5, 1.0, 1.5, and 2.0 wt%) of titanium dioxide (TiO2) nanoparticles via phase inversion technique to achieve hydrophilicity along with high selectivity for copper removal. The developed fibers were characterized based on scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), permeability, porosity, zeta potential, and contact angle. The improved membrane (with 1.0 wt% TiO2) concentration recorded the maximum flux (223 L/m2·h) and copper rejection (98.18%). Similarly, 1.0 wt% concentration of TiO2 nanoparticles made the membrane matrix more hydrophilic with the least contact angle of 50.01°. The maximum copper adsorption capacity of 69.68 mg/g was attained at 1.0 wt% TiO2 concentration. The experimental data of adsorption capacity were best fitted to the Freundlich isotherm model with R2 value of 0.99573. The hybrid membrane developed in this study has considerably eliminated copper from leachate and the concentration of copper in the permeate was substantially reduced to 0.044 mg/L, which is below standard discharge threshold.

scholarly journals Evaluate of head loss, sediment value and copper removal in sand media (rapid sand filter)

2014 ◽  
Vol 3 (2) ◽  
pp. 276-286 ◽  
Author(s):  
Daneshi Navab ◽  
Banejad Hossein ◽  
Pirtag Hamedany Reza ◽  
Daneshi Vahab ◽  
Farokhi Maedeh
Keyword(s):  
Water Resources ◽  
Copper Concentration ◽  
Technology Development ◽  
Wastewater Treatment Plants ◽  
Single Layer ◽  
Head Loss ◽  
Copper Removal ◽  
Time Interval ◽  
Water And Wastewater Treatment ◽  
Sand Filter

Along with the technology development and increasing consumption of water resources, we are experiencing low qualities in the mentioned resources. Copper brings about serious environment al pollution, threatening human health and ecosystem. This metal found variously in water resources and industrial activities. Therefore, it needs to treat the water resources from these excessive amounts. Different methods have used for this reason but the most used method during recent years has been the absorption by economic absorbers such as sand. Rapid sand filters usually used in water and wastewater treatment plants for water clarification. In this research, a single layer gravity rapid sand filter has used to reduce different concentrations of copper. sediment value and head loss arising in filter media is simulated by using combination of Carman-Kozeny, Rose and Gregory models in different discharges of rapid sand filter. Results have shown that with increasing in discharge and decreasing in input copper concentration, arriving time to given head loss, is increasing. In addition, results demonstrated that with increasing in copper concentration in influent, removal efficiency is decreasing somewhat. Results of this research can applied in an appropriate design of rapid sand filter to copper removal, a prediction of rapid sand filter ability to copper removal and an estimation of arising head loss during filter work thus evaluating of time interval backwash. DOI: http://dx.doi.org/10.3126/ije.v3i2.10641 International Journal of the Environment Vol.3(2) 2014: 276-286

Utilization of Electrochemical Techniques for Copper Removal, Speciation, and Analysis in Aqueous Systems

2019 ◽  
Vol 28 (18) ◽  
pp. 59-68 ◽  
Author(s):  
Jewel A. Gomes ◽  
Kamrul Islam ◽  
Mohammad R. Islam ◽  
George Irwin ◽  
Paul Bernazzani ◽  
...  
Keyword(s):  
Electrochemical Techniques ◽  
Copper Removal ◽  
Aqueous Systems

Effects of Alkaline Nano-SiO2 Abrasive on Planarization of 300mm Copper Patterned Wafer

2013 ◽  
Vol 634-638 ◽  
pp. 2949-2954
Author(s):  
Xin Liang Tang ◽  
Yu Ling Liu ◽  
Hong Yuan Zhang ◽  
Jie Bao
Keyword(s):  
Removal Rate ◽  
Chemical Mechanical Planarization ◽  
Initial Step ◽  
Step Height ◽  
Copper Removal ◽  
Copper Wafers

Silica abrasive plays an important role in chemical mechanical planarization (CMP) of copper. In this paper, effect of different silica abrasive concentrations on copper removal rate and planarization performance of copper was investigated. The results show that the copper removal rate was increased as the concentration of silica abrasive increase. However, excessive abrasive will lead to a decreased copper removal rate. The initial step height values of the multilayer copper wafers were all about 2500Å, and after being polished for 30s, the remaining values of step height of slurry A, B, C and D were 717 Å, 906 Å, 1222 Å and 1493 Å. It indicates that alkaline copper slurries with different abrasive concentrations all had a good planarization performance on copper patterned wafer CMP. As the abrasive concentration increased, the planarization capability was enhanced.

The application of wetland technology for copper removal from distillery wastewater: a case study

2009 ◽  
Vol 60 (11) ◽  
pp. 2759-2766 ◽  
Author(s):  
C. Murphy ◽  
P. Hawes ◽  
D. J. Cooper
Keyword(s):  
Metal Removal ◽  
Copper Removal ◽  
Ionic Form ◽  
Reed Beds ◽  
Organic Species ◽  
Treatment Processes ◽  
Distillery Wastewater ◽  
Reed Bed ◽  
Performance Results

The ability of reed beds to remove significant levels of metals from effluent streams is well cited in the literature. Various methods of removal have been postulated and demonstrated including physical methods such as filtration and settlement, precipitation when the metal is present as a salt and adsorption to organic species or take up by macrophytes when the metal is in a soluble or ionic form. Consequently, reed beds have been used in a variety of applications for metal removal in water treatment processes. The distillation process for whisky generates an effluent containing a significant amount of copper which is scoured from the copper stills during the process and cleaning operations. High soluble copper concentrations can breach discharge consents. A horizontal subsurface flow reed bed system has been designed and installed for copper removal at a distillery in Scotland. This paper presents the findings of the literature search, outlines the design of the bed and reviews the performance results.

Fly ash based geopolymer for heavy metal removal: A case study on copper removal

2015 ◽  
Vol 3 (3) ◽  
pp. 1669-1677 ◽  
Author(s):  
Mohammad S. Al-Harahsheh ◽  
Kamel Al Zboon ◽  
Leema Al-Makhadmeh ◽  
Muhannad Hararah ◽  
Mehaysen Mahasneh
Keyword(s):  
Heavy Metal ◽  
Fly Ash ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Copper Removal
Sign in / Sign up

Export Citation Format

Share Document