scholarly journals Augmentation of the Heat Transfer Performance of a Sinusoidal Corrugated Enclosure by Employing Hybrid Nanofluid

2014 ◽  
Vol 6 ◽  
pp. 147059 ◽  
Author(s):  
Behrouz Takabi ◽  
Saeed Salehi
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Heated Surface ◽  
Pure Water ◽  
Maximum Error ◽  
Temperature Fields ◽  
Working Fluid ◽  
Hybrid Nanofluid ◽  
Transfer Performance ◽  
Lower Temperature

This paper numerically examines laminar natural convection in a sinusoidal corrugated enclosure with a discrete heat source on the bottom wall, filled by pure water, Al2O3/water nanofluid, and Al2O3-Cu/water hybrid nanofluid which is a new advanced nanofluid with two kinds of nanoparticle materials. The effects of Rayleigh number (103≤Ra≤106) and water, nanofluid, and hybrid nanofluid (in volume concentration of 0% ≤ ϕ ≤ 2%) as the working fluid on temperature fields and heat transfer performance of the enclosure are investigated. The finite volume discretization method is employed to solve the set of governing equations. The results indicate that for all Rayleigh numbers been studied, employing hybrid nanofluid improves the heat transfer rate compared to nanofluid and water, which results in a better cooling performance of the enclosure and lower temperature of the heated surface. The rate of this enhancement is considerably more at higher values of Ra and volume concentrations. Furthermore, by applying the modeling results, two correlations are developed to estimate the average Nusselt number. The results reveal that the modeling data are in very good agreement with the predicted data. The maximum error for nanofluid and hybrid nanofluid was around 11% and 12%, respectively.

EXPERIMENTAL STUDY ON THERMAL TRANSPORT PHENOMENON OF NANOFLUIDS AS WORKING FLUID IN HEAT EXCHANGER

2014 ◽  
Vol 22 (01) ◽  
pp. 1450005 ◽  
Author(s):  
SHUICHI TORII
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Horizontal Tube ◽  
Constant Heat Flux ◽  
Working Fluid ◽  
Transfer Performance ◽  
Nanoparticles Concentration ◽  
Transfer Behavior

This paper aims to study the convective heat transfer behavior of aqueous suspensions of nanoparticles flowing through a horizontal tube heated under constant heat flux condition. Consideration is given to the effects of particle concentration and Reynolds number on heat transfer enhancement and the possibility of nanofluids as the working fluid in various heat exchangers. It is found that (i) significant enhancement of heat transfer performance due to suspension of nanoparticles in the circular tube flow is observed in comparison with pure water as the working fluid, (ii) enhancement is intensified with an increase in the Reynolds number and the nanoparticles concentration, and (iii) substantial amplification of heat transfer performance is not attributed purely to the enhancement of thermal conductivity due to suspension of nanoparticles.

Experimental Investigation of Oscillating Heat Pipe With Hybrid Fluids of Liquid Metal and Water

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Tingting Hao ◽  
Hongbin Ma ◽  
Xuehu Ma
Keyword(s):  
Heat Transfer ◽  
Liquid Metal ◽  
Heat Pipe ◽  
Heat Input ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Experimental Results ◽  
Working Fluid ◽  
Transfer Performance ◽  
Oscillating Heat Pipe

A new oscillating heat pipe (OHP) charged with hybrid fluids can improve thermal performance. The key difference in this OHP is that it uses room temperature liquid metal (Galinstan consisting of gallium, indium, and tin) and water as the working fluid. The OHP was fabricated on a copper plate with six turns and a 3 × 3 mm2 cross section. The OHP with hybrid fluids as the working fluid was investigated through visual observation and thermal measurement. Liquid metal was successfully driven to flow through the OHP by the pressure difference between the evaporator and the condenser without external force. Experimental results show that while added liquid metal can increase the heat transport capability, liquid metal oscillation amplitude decreases as the filling ratio of liquid metal increases. Visualization of experimental results show that liquid metal oscillation position and velocity increase as the heat input increases. Oscillating motion of liquid metal in the OHP significantly increases the heat transfer performance at high heat input. The lowest thermal resistance of 0.076 °C/W was achieved in the hybrid fluids-filled OHP with a heat input of 420 W. We experimentally demonstrated a 13% higher heat transfer performance using liquid metal as the working fluid compared to an OHP charged with pure water.

Heat Transfer Enhancement of Horizontal Oscillating Heat Pipes With Micro-/Nanostructured Surface

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
Tingting Hao ◽  
Huiwen Yu ◽  
Xuehu Ma ◽  
Zhong Lan
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Capillary Flow ◽  
Pure Water ◽  
Heat Pipes ◽  
Contact Angles ◽  
Horizontal Direction ◽  
Working Fluid ◽  
Transfer Performance ◽  
Nanostructured Surface

Abstract For oscillating heat pipes (OHPs) with low turn number (<9) positioned in the horizontal direction, the working fluid could not easily flow back to the evaporator due to the absence of gravity. Based on this, copper OHP with superhydrophilic micro-/nanostructured surface was investigated to enhance the heat transfer performance by introducing additional capillary force. OHPs with six turns were fabricated with bare copper and micro-/nanostructured inner surfaces for comparison. Pure water was used as the working fluid. Contact angles of water on the copper and superhydrophilic surfaces were 36.7 and 0 deg, respectively. The filling ratios of water were 50%, 65%, and 80%, respectively. Thermal resistance and liquid slug oscillations of OHPs were investigated at the heat input ranging from 100 to 380 W. Experimental results showed that OHPs with the superhydrophilic micro-/nanostructured surface showed an enhanced heat transfer performance due to the micro-/nanostructure-induced capillary flow in the horizontal direction. The optimum filling ratio was 65% in this work. The superhydrophilic micro-/nanostructured surface could significantly facilitate the backflow of the working fluid to the evaporator section and accelerate oscillating motions of liquid slugs. With the increasing of 0–70% in slug oscillating amplitude and 0–100% in slug oscillating velocity, micro-/nanostructured OHPs improved the heat transfer performance by up to 10% compared with the copper OHPs due to the wicking effect.

An Investigation of Flat-Plate Oscillating Heat Pipes

2010 ◽  
Author(s):  
Peng Cheng ◽  
Scott Thompson ◽  
Joe Boswell ◽  
Hongbin Ma
Keyword(s):  
Heat Transfer ◽  
Thermal Resistance ◽  
Flat Plate ◽  
Heat Transfer Performance ◽  
Operating Temperature ◽  
Pure Water ◽  
Heat Pipes ◽  
Copper Plate ◽  
Working Fluid ◽  
Transfer Performance

The heat transfer performance of flat-plate oscillating heat pipes (FP-OHPs) was investigated experimentally and theoretically. Two layers of channels were created by machining grooves on both sides of copper plate, in order to increase the channel number per unit volume. The channels had rectangular cross-sections with hydraulic diameters ranging from 0.762 mm to 1.389 mm. Acetone, water and diamond/acetone, gold/water and diamond/water nanofluids were tested as working fluids. It was found that the FP-OHP’s thermal resistance depended on the power input and operating temperature. The FP-OHP charged with pure water achieved a thermal resistance of 0.078°C/W while removing 560 W with a heat flux of 86.8 W/cm2. The thermal resistance was further decreased when nanofluid was used as the working fluid. A mathematical model predicting the heat transfer performance was developed to predict the effects of channel dimension, heating mode, working fluid and operating temperature on the thermal performance of the FP-OHP. Results presented here will assist in optimization of the FP-OHP and provide a better understanding of heat transfer mechanisms occurring in an OHPs.

Formation of Nano-Adsorption Layer and Its Effects on Nanofluid Spray Heat Transfer Performance

2015 ◽  
Vol 137 (2) ◽  
Author(s):  
Tong-Bou Chang
Keyword(s):  
Heat Transfer ◽  
Layer Thickness ◽  
Adsorption Layer ◽  
Heat Transfer Performance ◽  
Cooling System ◽  
Heated Surface ◽  
Spray Cooling ◽  
Working Fluid ◽  
Transfer Performance ◽  
Test Pieces

For spray cooling using nanofluid as the working fluid, a nano-adsorption layer is formed on the heated surface and affects the heat transfer performance of the cooling system. This study performs an experimental investigation into the formation of this nano-adsorption layer and its subsequent effects on the spray heat transfer performance of a cooling system using Al2O3–water nanofluid as the working fluid. The experiments consider four different nanoparticle volume fractions (i.e., 0 vol. %, 0.001 vol. %, 0.025 vol. %, and 0.05 vol. %) and two different surface roughnesses (i.e., 0.1 μm and 1.0 μm). The experimental results show that the 0.001 vol. % nanofluid yields the optimal heat transfer performance since most of the nanoparticles rebound from the heated surface directly on impact or are washed away by subsequently arriving droplets. The surface compositions of the spray-cooled specimens are examined using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). The results reveal that for all of the nanofluids, a nano-adsorption layer is formed on the surface of the spray-cooled test pieces. Moreover, the layer thickness increases with an increasing nanoparticle concentration. A greater nano-adsorption layer thickness not only results in a higher thermal resistance but also reduces the effect of the surface roughness in enhancing the heat transfer performance. In addition, the nano-adsorption layer absorbs the nanofluid droplets under the effects of capillary forces, and therefore reduces the contact angle, which induces a hydrophilic surface property.

Heat Transfer Augmentation of Aqueous Suspensions of Nanodiamonds in Turbulent Pipe Flow

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
Shuichi Torii ◽  
Wen-Jei Yang
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Horizontal Tube ◽  
Constant Heat Flux ◽  
Turbulent Pipe Flow ◽  
Working Fluid ◽  
Transfer Performance ◽  
Aqueous Suspensions

This paper aims to study the convective heat transfer behavior of aqueous suspensions of nanodiamond particles flowing through a horizontal tube heated under a constant heat flux condition. Consideration is given to the effects of particle concentration and Reynolds number on heat transfer enhancement. It is found that (i) significant enhancement of heat transfer performance due to suspension of nanodiamond particles in the circular tube flow is observed in comparison with pure water as the working fluid, (ii) the enhancement is intensified with an increase in the Reynolds number and the nanodiamond concentration, and (iii) substantial amplification of heat transfer performance is not attributed purely to the enhancement of thermal conductivity due to suspension of nanodiamond particles.

scholarly journals Conjugate heat transfer performance of stepped lid-driven cavity with Al2O3/water nanofluid under forced and mixed convection

2021 ◽  
Vol 3 (6) ◽  
Author(s):  
Naveen Janjanam ◽  
Rajesh Nimmagadda ◽  
Lazarus Godson Asirvatham ◽  
R. Harish ◽  
Somchai Wongwises
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Mixed Convection ◽  
Conjugate Heat Transfer ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Interface Temperature ◽  
Transfer Model ◽  
Transfer Performance ◽  
Driven Cavity

AbstractTwo-dimensional conjugate heat transfer performance of stepped lid-driven cavity was numerically investigated in the present study under forced and mixed convection in laminar regime. Pure water and Aluminium oxide (Al2O3)/water nanofluid with three different nanoparticle volume concentrations were considered. All the numerical simulations were performed in ANSYS FLUENT using homogeneous heat transfer model for Reynolds number, Re = 100 to 500 and Grashof number, Gr = 5000, 13,000 and 20,000. Effective thermal conductivity of the Al2O3/water nanofluid was evaluated by considering the Brownian motion of nanoparticles which results in 20.56% higher value for 3 vol.% Al2O3/water nanofluid in comparison with the lowest thermal conductivity value obtained in the present study. A solid region made up of silicon is present underneath the fluid region of the cavity in three geometrical configurations (forward step, backward step and no step) which results in conjugate heat transfer. For higher Re values (Re = 500), no much difference in the average Nusselt number (Nuavg) is observed between forced and mixed convection. Whereas, for Re = 100 and Gr = 20,000, Nuavg value of mixed convection is 24% higher than that of forced convection. Out of all the three configurations, at Re = 100, forward step with mixed convection results in higher heat transfer performance as the obtained interface temperature is lower than all other cases. Moreover, at Re = 500, 3 vol.% Al2O3/water nanofluid enhances the heat transfer performance by 23.63% in comparison with pure water for mixed convection with Gr = 20,000 in forward step.

scholarly journals Simulation approach on turbulent thermal performance factor of Al2O3-Cu/water hybrid nanofluid in circular and non-circular ducts

2021 ◽  
Vol 3 (3) ◽  
Author(s):  
Ing Jiat Kendrick Wong ◽  
Ngieng Tze Angnes Tiong
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Thermal Performance ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Hybrid Nanofluid ◽  
Performance Factor ◽  
Thermal Performance Factor ◽  
The Heat Transfer Coefficient

AbstractThis paper presents the numerical study of thermal performance factor of Al2O3-Cu/water hybrid nanofluid in circular and non-circular ducts (square and rectangular). Turbulent regime is studied with the Reynolds number ranges from 10000 to 100000. The heat transfer performance and flow behaviour of hybrid nanofluid are investigated, considering the nanofluid volume concentration between 0.1 and 2%. The thermal performance factor of hybrid nanofluid is evaluated in terms of performance evaluation criteria (PEC). This present numerical results are successfully validated with the data from the literature. The results indicate that the heat transfer coefficient and Nusselt number of Al2O3-Cu/water hybrid nanofluid are higher than those of Al2O3/water nanofluid and pure water. However, this heat transfer enhancement is achieved at the expense of an increased pressure drop. The heat transfer coefficient of 2% hybrid nanofluid is approximately 58.6% larger than the value of pure water at the Reynolds number of 10000. For the same concentration and Reynolds number, the pressure drop of hybrid nanofluid is 4.79 times higher than the pressure drop of water. The heat transfer performance is the best in the circular pipe compared to the non-circular ducts, but its pressure drop increment is also the largest. The hybrid nanofluid helps to improve the problem of low heat transfer characteristic in the non-circular ducts. In overall, the hybrid nanofluid flow in circular and non-circular ducts are reported to possess better thermal performance factor than that of water. The maximum attainable PEC is obtained by 2% hybrid nanofluid in the square duct at the Reynolds Number of 60000. This study can help to determine which geometry is efficient for the heat transfer application of hybrid nanofluid.

scholarly journals Numerical study of flow patterns and heat transfer in mini twisted oval tubes

2015 ◽  
Vol 26 (12) ◽  
pp. 1550140 ◽  
Author(s):  
Amin Ebrahimi ◽  
Ehsan Roohi
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Numerical Study ◽  
Critical Role ◽  
Reynolds Numbers ◽  
Flow Patterns ◽  
Working Fluid ◽  
Transfer Performance ◽  
Temperature Dependent ◽  
Overall Performance

Flow patterns and heat transfer inside mini twisted oval tubes (TOTs) heated by constant-temperature walls are numerically investigated. Different configurations of tubes are simulated using water as the working fluid with temperature-dependent thermo-physical properties at Reynolds numbers ranging between 500 and 1100. After validating the numerical method with the published correlations and available experimental results, the performance of TOTs is compared to a smooth circular tube. The overall performance of TOTs is evaluated by investigating the thermal-hydraulic performance and the results are analyzed in terms of the field synergy principle and entropy generation. Enhanced heat transfer performance for TOTs is observed at the expense of a higher pressure drop. Additionally, the secondary flow generated by the tube-wall twist is concluded to play a critical role in the augmentation of convective heat transfer, and consequently, better heat transfer performance. It is also observed that the improvement of synergy between velocity and temperature gradient and lower irreversibility cause heat transfer enhancement for TOTs.

Comparative Study of Cooling Performance of Automobile Radiator Using Al2O3-Water and Carbon Nanotube-Water Nanofluid

2014 ◽  
Vol 5 (1) ◽  
Author(s):  
Sandesh S. Chougule ◽  
S. K. Sahu
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Base Fluid ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Transfer Performance ◽  
Nanoparticle Concentration ◽  
Cooling Performance ◽  
Forced Convective Heat Transfer ◽  
Better Than

In the present study, the forced convective heat transfer performance of two different nanofluids, namely, Al2O3-water and CNT-water has been studied experimentally in an automobile radiator. Four different concentrations of nanofluid in the range of 0.15–1 vol. % were prepared by the additions nanoparticles into the water as base fluid. The coolant flow rate is varied in the range of 2 l/min–5 l/min. Nanocoolants exhibit enormous change in the heat transfer compared with the pure water. The heat transfer performance of CNT-water nanofluid was found to be better than Al2O3-water nanocoolant. Furthermore, the Nusselt number is found to increase with the increase in the nanoparticle concentration and nanofluid velocity.

Sign in / Sign up

Export Citation Format

Share Document