Formation of Nano-Adsorption Layer and Its Effects on Nanofluid Spray Heat Transfer Performance

2015 ◽  
Vol 137 (2) ◽  
Author(s):  
Tong-Bou Chang
Keyword(s):  
Heat Transfer ◽  
Layer Thickness ◽  
Adsorption Layer ◽  
Heat Transfer Performance ◽  
Cooling System ◽  
Heated Surface ◽  
Spray Cooling ◽  
Working Fluid ◽  
Transfer Performance ◽  
Test Pieces

For spray cooling using nanofluid as the working fluid, a nano-adsorption layer is formed on the heated surface and affects the heat transfer performance of the cooling system. This study performs an experimental investigation into the formation of this nano-adsorption layer and its subsequent effects on the spray heat transfer performance of a cooling system using Al2O3–water nanofluid as the working fluid. The experiments consider four different nanoparticle volume fractions (i.e., 0 vol. %, 0.001 vol. %, 0.025 vol. %, and 0.05 vol. %) and two different surface roughnesses (i.e., 0.1 μm and 1.0 μm). The experimental results show that the 0.001 vol. % nanofluid yields the optimal heat transfer performance since most of the nanoparticles rebound from the heated surface directly on impact or are washed away by subsequently arriving droplets. The surface compositions of the spray-cooled specimens are examined using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). The results reveal that for all of the nanofluids, a nano-adsorption layer is formed on the surface of the spray-cooled test pieces. Moreover, the layer thickness increases with an increasing nanoparticle concentration. A greater nano-adsorption layer thickness not only results in a higher thermal resistance but also reduces the effect of the surface roughness in enhancing the heat transfer performance. In addition, the nano-adsorption layer absorbs the nanofluid droplets under the effects of capillary forces, and therefore reduces the contact angle, which induces a hydrophilic surface property.

scholarly journals Augmentation of the Heat Transfer Performance of a Sinusoidal Corrugated Enclosure by Employing Hybrid Nanofluid

2014 ◽  
Vol 6 ◽  
pp. 147059 ◽  
Author(s):  
Behrouz Takabi ◽  
Saeed Salehi
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Heated Surface ◽  
Pure Water ◽  
Maximum Error ◽  
Temperature Fields ◽  
Working Fluid ◽  
Hybrid Nanofluid ◽  
Transfer Performance ◽  
Lower Temperature

This paper numerically examines laminar natural convection in a sinusoidal corrugated enclosure with a discrete heat source on the bottom wall, filled by pure water, Al2O3/water nanofluid, and Al2O3-Cu/water hybrid nanofluid which is a new advanced nanofluid with two kinds of nanoparticle materials. The effects of Rayleigh number (103≤Ra≤106) and water, nanofluid, and hybrid nanofluid (in volume concentration of 0% ≤ ϕ ≤ 2%) as the working fluid on temperature fields and heat transfer performance of the enclosure are investigated. The finite volume discretization method is employed to solve the set of governing equations. The results indicate that for all Rayleigh numbers been studied, employing hybrid nanofluid improves the heat transfer rate compared to nanofluid and water, which results in a better cooling performance of the enclosure and lower temperature of the heated surface. The rate of this enhancement is considerably more at higher values of Ra and volume concentrations. Furthermore, by applying the modeling results, two correlations are developed to estimate the average Nusselt number. The results reveal that the modeling data are in very good agreement with the predicted data. The maximum error for nanofluid and hybrid nanofluid was around 11% and 12%, respectively.

scholarly journals A Review on Development of Liquid Cooling System for Central Processing Unit (CPU)

2020 ◽  
Vol 78 (2) ◽  
pp. 98-113
Author(s):  
Muhammad Arif Harun ◽  
Nor Azwadi Che Sidik
Keyword(s):  
Heat Transfer ◽  
Heat Generation ◽  
Heat Transfer Performance ◽  
Cooling System ◽  
Electronic Devices ◽  
Working Fluid ◽  
Transfer Performance ◽  
Liquid Cooling ◽  
Cooling Performance ◽  
Liquid Cooling System

Electronic devices are becoming more efficient while getting a smaller size and compact design thus increase heat generation significantly. High heat generation from high technology electronic devices are needed to be cool down or control its temperature to prevent overheating problems. Due to the high cooling performance of liquid cooling, the electronic cooling system is shifting from an air-cooling system to a liquid cooling system. In the past few decades, numerous methods proposed by researchers for the central process unit (CPU) cooling using the liquid system either active cooling or passive cooling system. Other than physical configuration such as heat sink design, different configurations of working fluids are widely been studied by most of the researchers. Different working fluids have different heat transfer performance. Furthermore, a recent study has come out more interesting finding using nanofluid which can enhance heat transfer performance of liquid cooling. Nanofluid is a working fluid that has nanoparticles disperse in the base fluid which can increase the thermal properties of the based fluid. In this paper, comprehensive literature on the type of working fluid used in the respective system and methods of liquid cooling system for CPU including its cooling performance. Furthermore, this review paper discussed the different configuration of the liquid block and also the working fluid that had been used in the CPU cooling system.

Experimental investigation into spray cooling heat transfer performance of Al2O3-water nanofluid with different subcooling degrees

2021 ◽  
pp. 095440892110378
Author(s):  
Tong-Bou Chang ◽  
Tsung-Han Lin ◽  
Jhong-Wei Huang
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Heat Transfer Performance ◽  
Gradual Increase ◽  
Heated Surface ◽  
Operating Time ◽  
Spray Cooling ◽  
Transfer Performance ◽  
The Heat Transfer Coefficient

This study investigated the spray cooling heat transfer performance of Al2O3-water nanofluid given four different subcooling degrees (0 °C, 10 °C, 20 °C, and 30 °C). The results showed that the subcooled nanofluids were ranked in order of a reducing spray cooling heat transfer performance as follows: 20 °C, 10 °C, 0 °C, and 30 °C. On average, the heat transfer coefficient obtained using the nanofluid with 20 °C subcooling was around 8.3%, 8.6%, and 15.6% higher than that obtained with 10 °C, 0 °C, and 30 °C subcooling, respectively. However, the heat transfer performance decreased with an increasing spray operating time. The scanning electron microscopy observations showed that the reduction in the heat transfer coefficient was the result of a gradual increase in the thickness of the nano-adsorption layer on the heated surface as the spray operating time increased.

EXPERIMENTAL STUDY ON THERMAL TRANSPORT PHENOMENON OF NANOFLUIDS AS WORKING FLUID IN HEAT EXCHANGER

2014 ◽  
Vol 22 (01) ◽  
pp. 1450005 ◽  
Author(s):  
SHUICHI TORII
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Horizontal Tube ◽  
Constant Heat Flux ◽  
Working Fluid ◽  
Transfer Performance ◽  
Nanoparticles Concentration ◽  
Transfer Behavior

This paper aims to study the convective heat transfer behavior of aqueous suspensions of nanoparticles flowing through a horizontal tube heated under constant heat flux condition. Consideration is given to the effects of particle concentration and Reynolds number on heat transfer enhancement and the possibility of nanofluids as the working fluid in various heat exchangers. It is found that (i) significant enhancement of heat transfer performance due to suspension of nanoparticles in the circular tube flow is observed in comparison with pure water as the working fluid, (ii) enhancement is intensified with an increase in the Reynolds number and the nanoparticles concentration, and (iii) substantial amplification of heat transfer performance is not attributed purely to the enhancement of thermal conductivity due to suspension of nanoparticles.

scholarly journals Numerical study of flow patterns and heat transfer in mini twisted oval tubes

2015 ◽  
Vol 26 (12) ◽  
pp. 1550140 ◽  
Author(s):  
Amin Ebrahimi ◽  
Ehsan Roohi
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Numerical Study ◽  
Critical Role ◽  
Reynolds Numbers ◽  
Flow Patterns ◽  
Working Fluid ◽  
Transfer Performance ◽  
Temperature Dependent ◽  
Overall Performance

Flow patterns and heat transfer inside mini twisted oval tubes (TOTs) heated by constant-temperature walls are numerically investigated. Different configurations of tubes are simulated using water as the working fluid with temperature-dependent thermo-physical properties at Reynolds numbers ranging between 500 and 1100. After validating the numerical method with the published correlations and available experimental results, the performance of TOTs is compared to a smooth circular tube. The overall performance of TOTs is evaluated by investigating the thermal-hydraulic performance and the results are analyzed in terms of the field synergy principle and entropy generation. Enhanced heat transfer performance for TOTs is observed at the expense of a higher pressure drop. Additionally, the secondary flow generated by the tube-wall twist is concluded to play a critical role in the augmentation of convective heat transfer, and consequently, better heat transfer performance. It is also observed that the improvement of synergy between velocity and temperature gradient and lower irreversibility cause heat transfer enhancement for TOTs.

scholarly journals Analysis of Wetting Characteristics on Microstructured Hydrophobic Surfaces for the Passive Containment Cooling System

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Wei Zhao ◽  
Xiang Zhang ◽  
Chunlai Tian ◽  
Zhan Gao
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Cooling System ◽  
Heat Removal ◽  
Interface State ◽  
Transfer Performance ◽  
Hydrophobic Property ◽  
High Mechanical Strength ◽  
Feasible Solutions ◽  
Baxter Model

As the heat transfer surface in the passive containment cooling system, the anticorrosion coating (AC) of steel containment vessel (CV) must meet the requirements on heat transfer performance. One of the wall surface ACs with simple structure, high mechanical strength, and well hydrophobic characteristics, which is conductive to form dropwise condensation, is significant for the heat removal of the CV. In this paper, the grooved structures on silicon wafers by lithographic methods are systematically prepared to investigate the effects of microstructures on the hydrophobic property of the surfaces. The results show that the hydrophobicity is dramatically improved in comparison with the conventional Wenzel and Cassie-Baxter model. In addition, the experimental results are successfully explained by the interface state effect. As a consequence, it is indicated that favorable hydrophobicity can be obtained even if the surface is with lower roughness and without any chemical modifications, which provides feasible solutions for improving the heat transfer performance of CV.

scholarly journals Enhanced heat transfer characteristics of conjugated air jet impingement on a finned heat sink

2017 ◽  
Vol 21 (1 Part A) ◽  
pp. 279-288 ◽  
Author(s):  
Shuxia Qiu ◽  
Peng Xu ◽  
Liping Geng ◽  
Arun Mujumdar ◽  
Zhouting Jiang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Heat Sink ◽  
Heat Transfer Performance ◽  
Cooling System ◽  
Flow Characteristics ◽  
Jet Impingement ◽  
Transfer Performance ◽  
Transfer Enhancement ◽  
Air Jet

Air jet impingement is one of the effective cooling techniques employed in micro-electronic industry. To enhance the heat transfer performance, a cooling system with air jet impingement on a finned heat sink is evaluated via the computational fluid dynamics method. A two-dimensional confined slot air impinging on a finned flat plate is modeled. The numerical model is validated by comparison of the computed Nusselt number distribution on the impingement target with published experimental results. The flow characteristics and heat transfer performance of jet impingement on both of smooth and finned heat sinks are compared. It is observed that jet impingement over finned target plate improves the cooling performance significantly. A dimensionless heat transfer enhancement factor is introduced to quantify the effect of jet flow Reynolds number on the finned surface. The effect of rectangular fin dimensions on impingement heat transfer rate is discussed in order to optimize the cooling system. Also, the computed flow and thermal fields of the air impingement system are examined to explore the physical mechanisms for heat transfer enhancement.

Sign in / Sign up

Export Citation Format

Share Document