scholarly journals Safety Analysis of Solar Module under Partial Shading

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Wei He ◽  
Fengshou Liu ◽  
Jie Ji ◽  
Shengyao Zhang ◽  
Hongbing Chen
Keyword(s):  
Solar Cells ◽  
Power Dissipation ◽  
Hot Spot ◽  
Single Cells ◽  
Short Circuit ◽  
Heating Power ◽  
Maximum Point ◽  
Solar Module ◽  
Partial Shading ◽  
Efficient Alternative

Hot spot often occurs in a module when the qualities of solar cells mismatch and bypass diodes are proved to be an efficient alternative to reduce the effect of hot spot. However, these principles choosing a diode are based on the parameters of bypass diodes and PV cells without consideration of the maximum heating power of the shaded cell, which may cause serious consequences. On this basis, this paper presents a new approach to investigate partially shaded cells in different numbers of PV cells and different shading scenarios, including inhomogeneous illumination among solar cells and incomplete shading in one cell, which innovatively combines the same cells or divides one affected cell into many small single cells and then combines the same ones, and analyzes the shaded cell. The results indicate that the maximum power dissipation of the shaded cell occurs at short-circuit conditions. With the number of solar cells increasing, the shaded cell transfers from generating power to dissipating power and there is a maximum point of power dissipation in different shading situations that may lead to severe hot spot. Adding up the heat converted from solar energy, the heating power can be higher. In this case, some improvements about bypass diodes are proposed to reduce hot spot.

Microcavity tandem solar cells with a short circuit current higher than single cells

2013 ◽  
Vol 114 ◽  
pp. 59-64 ◽  
Author(s):  
Yang-Eun Lee ◽  
Sei-Yong Kim ◽  
Won-Ik Jeong ◽  
Jang-Joo Kim
Keyword(s):  
Solar Cells ◽  
Single Cells ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Tandem Solar Cells

scholarly journals Design, Electrical, and Optical Modelling of Bulk Heterojunction Polymer Solar Cell

2018 ◽  
Vol 2018 ◽  
pp. 1-6
Author(s):  
Muhammad Ali ◽  
Ahmed Shuja ◽  
Ahsan Baig ◽  
Erum Jamil ◽  
Muhammad Amjad
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Polymer Solar Cell ◽  
Bulk Heterojunction ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Clean Energy ◽  
Open Circuit ◽  
Solar Module ◽  
Donor And Acceptor

The energy scenario today is focused on the development and usage of solar cells, especially in the paradigm of clean energy. To readily create electron and hole pairs, solar cells utilize either photoactive or photosensitive components. A bulk heterojunction (BHJ) is a nanolayer consisting of donor and acceptor components with a large interpenetrated acceptor and donor contact area. In this context, a mix of P3HT and PCBM offers novelty for its use as an acceptor as well as a donor. In the work presented here, we address the mechanism of modelling and characterization of a BHJ-based polymer solar cell. Here, a new design of BHJ polymer solar cells have been designed, modelled, using Silvaco TCAD in the Organic Solar module, and matched with an already assembled device having similar features. Using this model, we have been able to estimate key parameters for the modelled devices, such as the short-circuit current density, open-circuit voltage, and fill factor with less than 0.25 error index compared to the fabricated counterpart, paving the way for fabless polymer solar cell design and optimization.

scholarly journals Analysis of the hard and soft shading impact on photovoltaic module performance using solar module tester

2019 ◽  
Vol 10 (2) ◽  
pp. 1014
Author(s):  
Mustafa Hamid Al-Jumaili ◽  
Ahmed Subhi Abdalkafor ◽  
Mohammed Qasim Taha
Keyword(s):  
Output Power ◽  
Solar Irradiance ◽  
Short Circuit ◽  
Renewable Energy Sources ◽  
Short Circuit Current ◽  
Small Scale ◽  
Photovoltaic Module ◽  
Solar Module ◽  
Partial Shading ◽  
Usual Condition

Solar cells are a major alternate source of sustainable energy in the usual condition of depleting non- renewable energy sources. Nowadays, this source is getting more and more important due to its use in large and small-scale installations. One of the major causes of energy losses in photovoltaic (PV) modules is the shading. It can happen due to clouds passing, near trees, and/or neighboring structures. Generally, there are two types of PV module Shading which are either partial shading or complete shading. Both have a significant impact on the solar module output power. This paper is an attempt of carrying out a study of the electrical characteristics of a solar module with various percentages of simulated shading. The solar module tester (SMT) simulator was used in this study. The study approved the direct correlation between short-circuit current and solar irradiance. The advantage of using SMT is its stable irradiance in comparison to the practical unstable solar irradiance within the same period. The results of both methods of shading simulation show that shading has a significant impact on the performance of solar panel in terms of efficiency, fill factor and output power. For better performance, solar panels should install in shading free places as much as its possible.

Lock-in Thermography-Based Local Efficiency Analysis of Solar Cells

2012 ◽  
Author(s):  
Otwin Breitenstein
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Efficiency Analysis ◽  
Open Circuit ◽  
Local Defect ◽  
Whole Cell ◽  
Local Efficiency ◽  
Cell Efficiency ◽  
Lock In ◽  
Efficiency Data

Abstract The electronic properties of solar cells, particularly multicrystalline silicon-based ones, are distributed spatially inhomogeneous, where regions of poor quality may degrade the performance of the whole cell. These inhomogeneities mostly affect the dark current-voltage (I-V) characteristic, which decisively affects the efficiency. Since the grid distributes the local voltage homogeneously across the cell and leads to lateral balancing currents, local light beam-induced current methods alone cannot be used to image local cell efficiency parameters. Lock-in thermography (LIT) is the method of choice for imaging inhomogeneities of the dark I-V characteristic. This contribution introduces a novel method for evaluating a number of LIT images taken at different applied biases. By pixel-wise fitting the data to a two diode model and taking into account local series resistance and short circuit current density data, realistically simulated images of the other cell efficiency parameters (open circuit voltage, fill factor, and efficiency) are obtained. Moreover, simulated local and global dark and illuminated I-V characteristics are obtained, also for various illumination intensities. These local efficiency data are expectation values, which would hold if a homogeneous solar cell had the properties of the selected region of the inhomogeneous cell. Alternatively, also local efficiency data holding for the cell working at its own maximum power point may be generated. The amount of degradation of different cell efficiency parameters in some local defect positions is an indication how dangerous these defects are for degrading this parameter of the whole cell. The method allows to virtually 'cut out' certain defects for checking their influence on the global characteristics. Thus, by applying this method, a detailed local efficiency analysis of locally inhomogeneous solar cells is possible. It can be reliably predicted how a cell would improve if certain defects could be avoided. This method is implemented in a software code, which is available.

Determining the exciton diffusion length of copper phthalocyanine in operating planar-heterojunction organic solar cells

2020 ◽  
Vol 89 (3) ◽  
pp. 30201 ◽  
Author(s):  
Xi Guan ◽  
Shiyu Wang ◽  
Wenxing Liu ◽  
Dashan Qin ◽  
Dayan Ban
Keyword(s):  
Solar Cells ◽  
Organic Solar Cells ◽  
Diffusion Length ◽  
Copper Phthalocyanine ◽  
Short Circuit ◽  
Thick Layer ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Exciton Diffusion ◽  
Exciton Diffusion Length

Organic solar cells based on planar copper phthalocyanine (CuPc)/C60 heterojunction have been characterized, in which a 2 nm-thick layer of bathocuproine (BCP) is inserted into the CuPc layer. The thin layer of BCP allows hole current to tunnel it through but blocks the exciton diffusion, thereby altering the steady-state exciton profile in the CuPc zone (zone 1) sandwiched between BCP and C60. The short-circuit current density (JSC) of device is limited by the hole-exciton scattering effect at the BCP/CuPc (zone 1) interface. Based on the variation of JSC with the width of zone 1, the exciton diffusion length of CuPc is deduced to be 12.5–15 nm. The current research provides an easy and helpful method to determine the exciton diffusion lengths of organic electron donors.

scholarly journals High performance tandem organic solar cells via a strongly infrared-absorbing narrow bandgap acceptor

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Zhenrong Jia ◽  
Shucheng Qin ◽  
Lei Meng ◽  
Qing Ma ◽  
Indunil Angunawela ◽  
...  
Keyword(s):  
Solar Cells ◽  
Power Conversion Efficiency ◽  
Conversion Efficiency ◽  
Organic Solar Cells ◽  
High Performance ◽  
Short Circuit ◽  
Power Conversion ◽  
High Power Conversion Efficiency ◽  
Device Structure ◽  
Narrow Bandgap

AbstractTandem organic solar cells are based on the device structure monolithically connecting two solar cells to broaden overall absorption spectrum and utilize the photon energy more efficiently. Herein, we demonstrate a simple strategy of inserting a double bond between the central core and end groups of the small molecule acceptor Y6 to extend its conjugation length and absorption range. As a result, a new narrow bandgap acceptor BTPV-4F was synthesized with an optical bandgap of 1.21 eV. The single-junction devices based on BTPV-4F as acceptor achieved a power conversion efficiency of over 13.4% with a high short-circuit current density of 28.9 mA cm−2. With adopting BTPV-4F as the rear cell acceptor material, the resulting tandem devices reached a high power conversion efficiency of over 16.4% with good photostability. The results indicate that BTPV-4F is an efficient infrared-absorbing narrow bandgap acceptor and has great potential to be applied into tandem organic solar cells.

scholarly journals Numerical Investigation of Graphene as a Back Surface Field Layer on the Performance of Cadmium Telluride Solar Cell

Molecules ◽  
2021 ◽  
Vol 26 (11) ◽  
pp. 3275
Author(s):  
Devendra KC ◽  
Deb Kumar Shah ◽  
M. Shaheer Akhtar ◽  
Mira Park ◽  
Chong Yeal Kim ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Doping Concentration ◽  
Carrier Lifetime ◽  
Short Circuit ◽  
Back Surface ◽  
Back Surface Field ◽  
Cdte Solar Cell ◽  
Cdte Solar Cells ◽  
Surface Field

This paper numerically explores the possibility of ultrathin layering and high efficiency of graphene as a back surface field (BSF) based on a CdTe solar cell by Personal computer one-dimensional (PC1D) simulation. CdTe solar cells have been characterized and studied by varying the carrier lifetime, doping concentration, thickness, and bandgap of the graphene layer. With simulation results, the highest short-circuit current (Isc = 2.09 A), power conversion efficiency (h = 15%), and quantum efficiency (QE ~ 85%) were achieved at a carrier lifetime of 1 × 103 ms and a doping concentration of 1 × 1017 cm−3 of graphene as a BSF layer-based CdTe solar cell. The thickness of the graphene BSF layer (1 mm) was proven the ultrathin, optimal, and obtainable for the fabrication of high-performance CdTe solar cells, confirming the suitability of graphene material as a BSF. This simulation confirmed that a CdTe solar cell with the proposed graphene as the BSF layer might be highly efficient with optimized parameters for fabrication.

scholarly journals The Influence of the Thickness of Compact TiO2 Electron Transport Layer on the Performance of Planar CH3NH3PbI3 Perovskite Solar Cells

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3295
Author(s):  
Andrzej Sławek ◽  
Zbigniew Starowicz ◽  
Marek Lipiński
Keyword(s):  
Solar Cells ◽  
Electron Transport ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Perovskite Solar Cells ◽  
Precursor Solution ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Transport Layer ◽  
Electron Transport Layer

In recent years, lead halide perovskites have attracted considerable attention from the scientific community due to their exceptional properties and fast-growing enhancement for solar energy harvesting efficiency. One of the fundamental aspects of the architecture of perovskite-based solar cells (PSCs) is the electron transport layer (ETL), which also acts as a barrier for holes. In this work, the influence of compact TiO2 ETL on the performance of planar heterojunction solar cells based on CH3NH3PbI3 perovskite was investigated. ETLs were deposited on fluorine-doped tin oxide (FTO) substrates from a titanium diisopropoxide bis(acetylacetonate) precursor solution using the spin-coating method with changing precursor concentration and centrifugation speed. It was found that the thickness and continuity of ETLs, investigated between 0 and 124 nm, strongly affect the photovoltaic performance of PSCs, in particular short-circuit current density (JSC). Optical and topographic properties of the compact TiO2 layers were investigated as well.

scholarly journals CdTe-Based Thin Film Solar Cells: Past, Present and Future

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1684
Author(s):  
Alessandro Romeo ◽  
Elisa Artegiani
Keyword(s):  
Thin Film ◽  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Early Years ◽  
Solar Cell Efficiency ◽  
Cell Efficiency

CdTe is a very robust and chemically stable material and for this reason its related solar cell thin film photovoltaic technology is now the only thin film technology in the first 10 top producers in the world. CdTe has an optimum band gap for the Schockley-Queisser limit and could deliver very high efficiencies as single junction device of more than 32%, with an open circuit voltage of 1 V and a short circuit current density exceeding 30 mA/cm2. CdTe solar cells were introduced at the beginning of the 70s and they have been studied and implemented particularly in the last 30 years. The strong improvement in efficiency in the last 5 years was obtained by a new redesign of the CdTe solar cell device reaching a single solar cell efficiency of 22.1% and a module efficiency of 19%. In this paper we describe the fabrication process following the history of the solar cell as it was developed in the early years up to the latest development and changes. Moreover the paper also presents future possible alternative absorbers and discusses the only apparently controversial environmental impacts of this fantastic technology.

Sign in / Sign up

Export Citation Format

Share Document