scholarly journals Mechanical Bed for Investigating Sleep-Inducing Vibration

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Hitoshi Kimura ◽  
Akisue Kuramoto ◽  
Yuma Inui ◽  
Norio Inou

In running cars or trains, passengers often feel sleepy. Our study focuses on this physiological phenomenon. If a machine can reproduce this phenomenon, it is feasible to put a person, such as an insomnia patient or an infant, to sleep without any harmful effects. The results of our previous study suggest that low-frequency vibration induces sleep. This report describes a new mechanical bed for inducing sleep and discusses the effects of different vibration conditions. The new bed has two active DOFs in the vertical and horizontal directions to examine the anisotropy of sensation. The bed includes three main parts: a vertical driver unit, a horizontal driver unit, and a unique 2-DOF counterweight system to reduce driving force and noise. With regard to motion accuracy, the maximum motion error in the vertical direction lifting 75 kg load was only 0.06 mm with a 5.0 mm amplitude of a 0.5 Hz sinusoidal wave. The results of excitation experiments with 10 subjects showed a significant difference in sleep latency between the conditions with vibration and without vibration. Furthermore, the average latency with insensible vibration (amplitude = 2.4 mm) was shorter than that with sensible vibration (amplitude = 7.5 mm). These results suggest the ability of appropriate vibration to induce sleep.

2021 ◽  
Author(s):  
Ramy Hussein ◽  
Ahmad Sadek ◽  
Mohamed Elbestawi ◽  
Helmi Attia

Abstract In this paper, the tool wear mechanism in low-frequency vibration-assisted drilling (LF-VAD) of carbon fiber reinforced polymer (CFRP)/Ti6Al4V stacks has been proposed using variably machining parameters. Based on the kinematics analysis, the effect of vibration amplitude on the chip formation, uncut chip thickness, chip radian, and axial velocity was presented. Subsequently, the effect of LF-VAD on the cutting temperature, tool wear, delamination, and geometrical accuracy was presented for different vibration amplitude. The LF-VAD with the utilization of minimum quantity lubricant (MQL) resulted in a successful drilling process of 50 holes, with a 63 % reduction of the cutting temperature. For the rake face, LF-VAD reduced the adhered height of Ti6Al4V by 80 % at low cutting speed and reduced the crater depth by 33 % at the high cutting speed. On the other hand, LF-VAD reduced the flank wear land by 53 %. Furthermore, LF-VAD showed a significant enhancement on the CFRP delamination, geometrical accuracy, and burr formation.


Author(s):  
Rajesh Govindan ◽  
Suraj Prakash Harsha

In this paper, the dynamic characteristics of the human body were investigated by developing a 3-D finite element model based on 50th percentile anthropometric data for a 54 kg Indian male subject in standing position by considering human body segments as an ellipsoid. The finite element modal analysis is carried out to extract several low-frequency vibration modes and its vibration mode shapes were presented in this paper. The results show that the lowest natural frequency of the standing passenger model occurs in the fore-and-aft direction. The second natural frequency occurs in the lateral direction and the first order natural frequency of the standing passenger model in the vertical direction occurs at 5.379 Hz. The model will be helpful to predict the vibration response of human body under various vibration environment encounters in the railway vehicle.


2021 ◽  
Vol 12 (3) ◽  
pp. 452-458
Author(s):  
O. I. Dotsenko ◽  
А. М. Mischenko ◽  
G. V. Taradina

The early signs of vibration effects on the human body are microcirculation and transcapillary metabolism disorders, accompanied by disruption of the supply to and utilization of oxygen in the tissues and organs. However, there are few experimental studies aimed at finding targets of vibration in cells and determining the action mechanism of vibration. In in vitro experiments, human erythrocytes in buffer solution were exposed to low-frequency vibration (frequency range 8–32 Hz, amplitudes 0.5–0.9 mm) for 3 hours. The dynamics of the accumulation of membrane-bound catalase and hemoglobin and the distribution of ligand hemoglobin in the membrane-bound fraction were studied as the indicators of functional activity of cells. The choice of these indicators is justified by the participation of catalase and hemoglobin in O2-dependent cellular reactions as a part of protein complexes. Since pО2 is a trigger of conformational transitions in the hemoglobin molecule, simultaneously with oxygen transport, hemoglobin signals to different metabolic systems about oxygen conditions in the environment. The studies revealed that in the conditions of vibration, the activity of membrane-associated catalase increased by 40–50% in the frequency range of 12–24 Hz (amplitude 0.5 ± 0.04 mm), by 20–30% in the amplitude of 0.9 mm, but after about 100–120 min exposure the enzyme activity decreased even below the control level. There was a dose-dependent accumulation of membrane-bound hemoglobin during exposure to vibration. In the membrane-bound fraction of hemoglobin, oxyhemoglobin had the highest content (60–80%), while the content of methemoglobin varied 5–20%. During vibrations in the frequency range 12–28 Hz, 0.5 mm, we recorded 10–30% increase in oxyhemoglobin. With increase in the vibration amplitude (0.9 mm) in the frequency range of 16–32 Hz, constant content of oxyhemoglobin was noted at the beginning of the experiment, which tended to decrease during the last exposure time. Frequency of 32 Hz caused increase in the deoxyhemoglobin content in the membrane-bound fraction. The content of methemoglobin (metHb) in erythrocytes significantly increased during exposure to the frequency range of 12–24 Hz, with the amplitude of 0.5 mm (1.3–2.4 times). During the exposure to frequencies of 28 and 32 Hz, we observed the transition of methemoglobin to hemichrome. The content of methemoglobin in the cells was lower and decreased at the end of the experiment when the vibration amplitude was 0.9 mm. In these experimental conditions, no increase in hemichrome content in the membrane-bound fraction was recorded. Therefore, the degree of binding of catalase and hemoglobin with the membrane of erythrocytes that were exposed to vibration and the changes in the content of ligand forms in the composition of membrane-bound hemoglobin are dose-dependent. Low-frequency vibration initiates O2-dependent processes in erythrocytes. Targets of such an influence are nanobubbles of dissolved air (babstons), retained on the surface of erythrocytes due to Coulomb interactions, capable of coagulation and increase in size under the action of vibration. At first, the consequences of these processes are increase in oxygen content in the surface of erythrocytes, and then decrease as a result of degassing. Thus, increase in oxygen content on the surface initiates redox reactions, whereas decrease in oxygen content leads to reconstruction of metabolic processes oriented at overcoming hypoxia.


Author(s):  
Minghuan Wang ◽  
Yaobin Zhang ◽  
Xufeng Xu ◽  
Guoda Chen ◽  
Adam T Clare ◽  
...  

Ribbed holes can serve to increase the efficiency of the heat exchangers and improve the performance of industrial equipment. Increasing demand for small ribbed holes is a key driver in manufacturing technology research. Electrochemical machining has been shown to be a promising method for this. In this paper, an intermittent low-frequency vibration tool is used to demonstrate significant improvement to the geometry of internal ribbed holes. The process stability, material removal rates, and uniformity of features along the flow direction are improved. Firstly, a 3D model of the flow field within the interelectrode gap was developed to calculate and governing flow regime in the interelectrode gap. The simulation demonstrated that the fluid velocity fluctuates periodically and this enhances electrolyte flushing in the interelectrode gap during the machining process. Then, experimental tests for the manufacture of spiral ribs on small holes (Ø1.5 mm and 20–40 mm depth) are also demonstrated with accompanying variation of the tool vibration amplitude and frequency, respectively. Results show that groove depth was most greatly influenced by the vibration amplitude and that better uniformity could be obtained at higher vibration frequencies. The groove depth increased by 15% over nonvibrating control tests with enhanced uniformity.


2019 ◽  
Vol 2019 ◽  
pp. 1-15 ◽  
Author(s):  
Vanliem Nguyen ◽  
Jianrun Zhang ◽  
Xiuzhi Yang

To improve the ride comfort of the off-road vibratory roller, the cab’s hydraulic mounts were analyzed to prevent vibration sources transmitting to the cab. However, the cab’s low-frequency shaking in the vertical direction and the direction of forward motion is still great. This study proposes an optimal fuzzy-PID control method for semi-active cab’s hydraulic mounts based on an off-road vehicle roller dynamic model to analyze the low-frequency performance of semi-active cab’s hydraulic mounts under the different operating conditions. In order to evaluate the ride comfort of the off-road vibratory roller with semi-active cab’s hydraulic mounts, the power spectral density (PSD) and the weighted root mean square (RMS) of acceleration responses of the vertical driver’s seat, cab’s pitch, and roll vibrations in the low-frequency range are chosen as objective functions. Contrastive analysis of low-frequency vibration characteristics of the off-road vibratory roller with passive cab’s hydraulic mounts, semi-active cab’s hydraulic mounts without optimization, and semi-active cab’s hydraulic mounts with optimization is, respectively, carried out. The research results show that the semi-active cab’s hydraulic mounts with optimization have an obvious effect on mitigating the cab shaking and improving the ride comfort in comparison with passive cab’s hydraulic mounts and semi-active cab’s hydraulic mounts without optimization.


Author(s):  
K. Hama

The lateral line organs of the sea eel consist of canal and pit organs which are different in function. The former is a low frequency vibration detector whereas the latter functions as an ion receptor as well as a mechano receptor.The fine structure of the sensory epithelia of both organs were studied by means of ordinary transmission electron microscope, high voltage electron microscope and of surface scanning electron microscope.The sensory cells of the canal organ are polarized in front-caudal direction and those of the pit organ are polarized in dorso-ventral direction. The sensory epithelia of both organs have thinner surface coats compared to the surrounding ordinary epithelial cells, which have very thick fuzzy coatings on the apical surface.


1992 ◽  
Vol 1 (4) ◽  
pp. 52-55 ◽  
Author(s):  
Gail L. MacLean ◽  
Andrew Stuart ◽  
Robert Stenstrom

Differences in real ear sound pressure levels (SPLs) with three portable stereo system (PSS) earphones (supraaural [Sony Model MDR-44], semiaural [Sony Model MDR-A15L], and insert [Sony Model MDR-E225]) were investigated. Twelve adult men served as subjects. Frequency response, high frequency average (HFA) output, peak output, peak output frequency, and overall RMS output for each PSS earphone were obtained with a probe tube microphone system (Fonix 6500 Hearing Aid Test System). Results indicated a significant difference in mean RMS outputs with nonsignificant differences in mean HFA outputs, peak outputs, and peak output frequencies among PSS earphones. Differences in mean overall RMS outputs were attributed to differences in low-frequency effects that were observed among the frequency responses of the three PSS earphones. It is suggested that one cannot assume equivalent real ear SPLs, with equivalent inputs, among different styles of PSS earphones.


Author(s):  
В. М. Мойсишин ◽  
M. V. Lyskanych ◽  
R. A. Zhovniruk ◽  
Ye. P. Majkovych

The purpose of the proposed article is to establish the causes of oscillations of drilling tool and the basic laws of the distribution of the total energy of the process of changing the axial dynamic force over frequencies of spectrum. Variable factors during experiments on the classical plan were the rigidity of drilling tool and the hardness of the rock. According to the results of research, the main power of the process of change of axial dynamic force during drilling of three roller cone bits is in the frequency range 0-32 Hz in which three harmonic frequency components are allocated which correspond to the theoretical values of low-frequency and gear oscillations of the chisel and proper oscillations of the bit. The experimental values of frequencies of harmonic components of energy and normalized spectrum as well as the magnitude of the dispersion of the axial dynamic force and its normalized values at these frequencies are presented. It has been found that with decreasing rigidity of the drilling tool maximum energy of axial dynamic force moves from the low-frequency oscillation region to the tooth oscillation area, intensifying the process of rock destruction and, at the same time, protecting the tool from the harmful effects of the vibrations of the bit. Reducing the rigidity of the drilling tool protects the bit from the harmful effects of the vibrations generated by the stand. The energy reductions in these fluctuations range from 47 to 77%.


Sign in / Sign up

Export Citation Format

Share Document