scholarly journals Composite Plate Phased Array Structural Health Monitoring Signal Reconstruction Based on Orthogonal Matching Pursuit Algorithm

2017 ◽  
Vol 2017 ◽  
pp. 1-7 ◽  
Author(s):  
Yajie Sun ◽  
Feihong Gu ◽  
Sai Ji ◽  
Lihua Wang
Keyword(s):  
Structural Health Monitoring ◽  
Health Monitoring ◽  
Phased Array ◽  
Matching Pursuit ◽  
Sampling Rate ◽  
Sampling Theorem ◽  
Structural Health ◽  
Array Technology ◽  
Ultrasonic Phased Array ◽  
Matching Pursuit Algorithm

In order to ensure the safety of composite components, structural health monitoring is needed to detect structural performance in real-time at the early stage of damage occurred. This is difficult to detect complex components with single sensor detection technology, so that ultrasonic phased array technology using multisensor detection will be selected. Ultrasonic phased array technology can scan the structure in all directions and angles without moving or less moving the probe and becomes the first choice of structural health monitoring. However, a large amount of data will be generated when using ultrasonic phased array with Nyquist sampling theorem for structural health monitoring and is difficult to storage, transmission, and processing. Besides, traditional Nyquist sampling cannot satisfy the sampling of large amounts of data without distortion, so a more efficient acquisition technique must be chosen. Compressive sensing theory can ensure that if the signal is sparse, it can be sampled in low sampling rate which is much less than two times of the sampling rate as defined by Nyquist sampling theorem for a large number of data and reconstructed in high probability. Then, the experiment result indicated that the orthogonal matching pursuit algorithm can reconstruct the signal completely and accurately.

Research on Parallel PZT Phased Array Based Structural Health Monitoring in CFPR

2013 ◽  
Vol 753-755 ◽  
pp. 2343-2346
Author(s):  
Ya Jie Sun ◽  
Yong Hong Zhang ◽  
Hui Qiang Tang ◽  
Cheng Shan Qian ◽  
Shen Fang Yuan
Keyword(s):  
Time Delay ◽  
Structural Health Monitoring ◽  
Health Monitoring ◽  
Lamb Wave ◽  
Phased Array ◽  
Signal Amplitude ◽  
Gray Scale ◽  
One Dimensional ◽  
Structural Health ◽  
Damage Location

Phased array theroy can controll the Lamb wave beem steering in certain range by adding the time delay to the signals. Phased array theory is used to identify the damge in the structure. One dimensional PZT array is restricted in monitoring distance. Two parellel PZT sensors arrays are utilized to monitor the CFPR structure to extend the monitoring distance and to improve the precision of the damage locatilization. The experiment is done on the CFPR structure by using two parellel PZT arrays to detect the damage in the structure. The results of the experiment is shown on the mapped image. Gray-scale in the mapped image from dark to light corresponds to the signal amplitude from low to high. The highlight of the mapped image is the damage location in the structure. The monitoring results in the CFPR structure by two parellel PZT arrays is accurate and identical.

An Impact-Based Experimental Setup for Evaluation of Rapid Electromechanical Impedance-Based Structural Health Monitoring

2020 ◽  
Author(s):  
Mohammad Alshaikh Ali ◽  
Eric C. Nolan ◽  
Steven R. Anton ◽  
Mohsen Safaei
Keyword(s):  
Structural Health Monitoring ◽  
Health Monitoring ◽  
Sampling Rate ◽  
Frequency Resolution ◽  
Experimental Setup ◽  
Frequency Bandwidth ◽  
Electromechanical Impedance ◽  
Excitation Signal ◽  
Structural Health ◽  
The Impact

Abstract This work investigates the application of structural health monitoring (SHM) in a dynamic environment with the electromechanical impedance (EMI) method. Classically, the EMI method monitors civil or mechanical structures for damage in static environments. Advances in data acquisition (DAQ) now allow the possibility of rapid damage detection in dynamic environments. An impact-based experimental setup is developed to create a repeatable dynamic event through a collision between a pneumatically actuated striker bar and a static incident bar instrumented with a piezoelectric transducer. The EMI method is employed to detect the change of state at the interface of the two colliding bars. Experimental results prove the pneumatic launching system is capable of repeatable dynamic events, but the duration of contact is only 0.03 ms and the current DAQ system is incapable of detecting the event. A 3D printed programming material interface is placed at the location of impact to increase the duration of contact to approximately 1 ms. An excitation signal is created to continuously sweep a 0.5 ms chirp signal with a frequency bandwidth from 60–70 kHz (previously identified damage sensitive frequency bandwidth from static testing) for 7.5 seconds. Results indicate that due to the sampling rate and sweep time of the excitation signal, the frequency resolution is not adequate to properly assess if the impact is detected. Improvements in the DAQ hardware must be considered for future work.

Removing the Ambiguity in Lamb Wave-Based Damage Localization

2009 ◽  
Vol 413-414 ◽  
pp. 79-86 ◽  
Author(s):  
Pawel Malinowski ◽  
Tomasz Wandowski ◽  
Wiesław M. Ostachowicz
Keyword(s):  
Structural Health Monitoring ◽  
Health Monitoring ◽  
Phased Array ◽  
Lamb Waves ◽  
Theoretical Calculations ◽  
Signal To Noise Ratio ◽  
Damage Localization ◽  
Monitoring Method ◽  
Structural Health ◽  
Starting Point

The aim of this work is the investigation and improvement of a Structural Health Monitoring method based on Lamb waves propagation. This research concentrates on ambiguity in damage localization using attached piezoelectric transducers as sources and sensors of the elastic waves. A linear phased array is chosen as a starting point of the investigation. It has a great advantage in damage localization, namely it enables to amplify the wave reflected from damage, increasing the signal to noise ratio, and precisely indicates not only the distance to damage from the array but also the direction on which the damage lies. However it has also a great disadvantage which needs to be handled – the localization results are symmetric in relation to the line on which the transducers of linear phased array are placed. This obviously does not facilitate Structural Health Monitoring process and precise indication of damage placement. Therefore this investigation aims to improve this localization method by removing the ambiguity in results. In this work the placement of transducers forming a linear phased array is modified to achieve this goal. Several array modification are investigated and compared in order to determine the best solution. Presented research is based on theoretical calculations as well as laboratory experiments on prepared specimens. The measurements are conducted with a compact 13–channel SHM system controlled by a MATLAB® script.

2-D Directional Phased Array Using Piezoelectric Paint to Detect Damages in Isotropic Plates

2009 ◽  
Author(s):  
Byungseok Yoo ◽  
Darryll J. Pines ◽  
Ashish S. Purekar
Keyword(s):  
Structural Health Monitoring ◽  
Damage Detection ◽  
Health Monitoring ◽  
Ultrasonic Testing ◽  
Phased Array ◽  
Guided Wave ◽  
In Situ Monitoring ◽  
Mode Shapes ◽  
Detection Techniques ◽  
Structural Health

Research interests in structural health monitoring have increased due to in-situ monitoring of structural components to detect damage. This can secure personal safety and reduce maintenance effort for mechanical systems. Conventional damage detection techniques known as nondestructive evaluation (NDE) have been conducted to detect and locate damaged area in structures. Ultrasonic testing, using ultrasonic transducers or electromagnetic acoustic transducers, is one of the most widespread NDE techniques, based on monitoring changes in acoustic impedance. Although the ultrasonic testing has advantages such as high sensitivity to discontinuities and evaluation accuracy, it requires testing surface accessibility, close location to the damaged area, and decent skill and training of technicians. In recent years, modal analysis techniques to capture changes of mode shapes and natural frequency of structures have been investigated. However, the technique is relatively insensitive to small amount of damage such as an initial crack which can rapidly grow in structures under cyclic loadings. In addition, structural health monitoring based on guided waves has become a preferred damage detection approach due to its quick examination of large area and simple inspection mechanisms. There are many techniques used to analyze sensor signals to bring out features related to damage. A phased array coupled with the guided wave approach has been introduced to effectively analyze complicated guided wave signals. Phased array theory as a directional filtering technique is usually used in antenna applications. By using phased array signal processing, virtually steering the array to find the largest response of source, the desired signal component can be enhanced while unwanted information is eliminated.

Sign in / Sign up

Export Citation Format

Share Document