scholarly journals Investigation of Performance and Rotor Tip Flow Field in a Low Speed Research Compressor with Circumferential Groove Casing Treatment at Varying Tip Clearance

2017 ◽  
Vol 2017 ◽  
pp. 1-14 ◽  
Author(s):  
Matthias Rolfes ◽  
Martin Lange ◽  
Ronald Mailach
Keyword(s):  
Flow Field ◽  
Operating Conditions ◽  
Single Stage ◽  
Tip Clearance ◽  
Experimental Investigations ◽  
Low Speed ◽  
Pressure Transducers ◽  
Casing Treatment ◽  
Operating Range ◽  
Circumferential Groove

Experimental investigations in a single-stage low speed axial research compressor are presented. The influence of four different rotor tip clearances on the overall compressor performance and on the rotor tip flow field is investigated in configurations with and without circumferential groove casing treatments. Piezo-resistive pressure transducers are used to capture the unsteady flow field in the rotor tip region. The investigated casing groove is effectively working at the three largest investigated tip clearance sizes. The largest achieved operating range increase by the groove is 6.9%. The groove can delay the upstream movement of the flow interface between leakage flow and main flow and thus increase the stable operating range. Rotating instabilities are shown to exist at large tip clearance sizes in throttled operating conditions. Their amplitudes can be damped by the casing groove. No modal activities could be detected in the current single-stage compressor build.

Experimental and Numerical Investigation of a Circumferential Groove Casing Treatment in a Low Speed Axial Research Compressor at Different Tip Clearances

2017 ◽  
Author(s):  
Matthias Rolfes ◽  
Martin Lange ◽  
Konrad Vogeler ◽  
Ronald Mailach
Keyword(s):  
Total Pressure ◽  
Solid Wall ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Chord Length ◽  
Single Stage ◽  
Tip Clearance ◽  
Low Speed ◽  
Operating Range ◽  
Circumferential Groove

The demand of increasing pressure ratios for modern high pressure compressors leads to decreasing blade heights in the last stages. As tip clearances cannot be reduced to any amount and minimum values might be necessary for safety reasons, the tip clearance ratios of the last stages can reach values notably higher than current norms. This can be intensified by a compressor running in transient operations where thermal differences can lead to further growing clearances. For decades, the detrimental effects of large clearances on an axial compressor’s operating range and efficiency are known and investigated. The ability of circumferential casing grooves in the rotor casing to improve the compressor’s operating range has also been in the focus of research for many years. Their simplicity and ease of installation are one reason for their continuing popularity nowadays, where advanced methods to increase the operating range of an axial compressor are known. In a previous paper [1], three different circumferential groove casing treatments were investigated in a single stage environment in the Low Speed Axial Research Compressor at TU Dresden. One of these grooves was able to notably improve the operating range and the efficiency of the single stage compressor at very large rotor tip clearances (5% of chord length). In this paper, the results of tests with this particular groove type in a three stage environment in the Low Speed Axial Research Compressor are presented. Two different rotor tip clearance sizes of 1.2% and 5% of tip chord length were investigated. At the small tip clearance, the grooves are almost neutral. Only small reductions in total pressure ratio and efficiency compared to the solid wall can be observed. If the compressor runs with large tip clearances it notably benefits from the casing grooves. Both, total pressure and efficiency can be improved by the grooves in a similar extent as in single stage tests. Five-hole probe measurements and unsteady wall pressure measurements show the influence of the groove on the flow field. With the help of numerical investigations the different behavior of the grooves at the two tip clearance sizes will be discussed.

Experimental and Numerical Investigation of a Circumferential Groove Casing Treatment in a Low-Speed Axial Research Compressor at Different Tip Clearances

2017 ◽  
Vol 139 (12) ◽  
Author(s):  
Matthias Rolfes ◽  
Martin Lange ◽  
Konrad Vogeler ◽  
Ronald Mailach
Keyword(s):  
Total Pressure ◽  
Solid Wall ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Chord Length ◽  
Single Stage ◽  
Low Speed ◽  
Casing Treatment ◽  
Operating Range ◽  
Circumferential Groove

The demand of increasing pressure ratios for modern high pressure compressors leads to decreasing blade heights in the last stages. As tip clearances (TC) cannot be reduced to any amount and minimum values might be necessary for safety reasons, the TC ratios of the last stages can reach values notably higher than current norms. This can be intensified by a compressor running in transient operations where thermal differences can lead to further growing clearances. For decades, the detrimental effects of large clearances on an axial compressor's operating range and efficiency are known and investigated. The ability of circumferential casing grooves in the rotor casing to improve the compressor's operating range has also been in the focus of research for many years. Their simplicity and ease of installation are one reason for their continuing popularity nowadays, where advanced methods to increase the operating range of an axial compressor are known. In the authors' previous paper, three different circumferential groove casing treatments were investigated in a single-stage environment in the low-speed axial research compressor at TU Dresden. One of these grooves was able to notably improve the operating range and the efficiency of the single stage compressor at very large rotor TC (5% of chord length). In this paper, the results of tests with this particular groove type in a three stage environment in the low-speed axial research compressor are presented. Two different rotor TC sizes of 1.2% and 5% of tip chord length were investigated. At the small TC, the grooves are almost neutral. Only small reductions in total pressure ratio and efficiency compared to the solid wall can be observed. If the compressor runs with large TC, it notably benefits from the casing grooves. Both, total pressure and efficiency can be improved by the grooves in a similar extent as in single stage tests. Five-hole probe measurements and unsteady wall pressure measurements show the influence of the groove on the flow field. With the help of numerical investigations, the different behavior of the grooves at the two TC sizes will be discussed.

Experimental Investigation of the Steady and Unsteady Flow Field in a Single Stage Low Pressure Axial Compressor With a Circumferential Groove Casing Treatment

2010 ◽  
Author(s):  
N. Van de Wyer ◽  
B. Farkas ◽  
J. Desset ◽  
J. F. Brouckaert ◽  
J.-F. Thomas ◽  
...  
Keyword(s):  
Experimental Investigation ◽  
Flow Field ◽  
Unsteady Flow ◽  
Axial Compressor ◽  
Low Pressure ◽  
Fast Response ◽  
Single Stage ◽  
Compressor Stage ◽  
Casing Treatment ◽  
Circumferential Groove

This paper deals with the experimental investigation of the influence of a circumferential groove casing treatment on the performance and stability margin of a single stage low pressure axial compressor. The design of the compressor stage is representative of a booster stage for the new counter-rotating turbofan engine architecture and is characterized by unusually high loading and flow coefficients. The choice of the circumferential groove is described on the basis of a numerical parametric study on the number of grooves, the axial position, the depth and width of the groove. The experiments were performed at a Reynolds number corresponding to cruise conditions in the von Karman Institute closed loop high speed compressor test rig R4. The detailed performance characterization of the compressor stage with casing treatment was mapped at four operating points from choke to stall at design speed. The compressor stall limit was determined at several other off-design speeds. Detailed steady and unsteady measurements were performed to determine the flow field characteristics of the rotor and of the complete stage. Conventional pressure, temperature and directional probes were used along with fast response pressure sensors in the rotor casing and in the groove. Simultaneous traverses with a fast response total pressure probe were used to map the unsteady flow field at the rotor exit allowing an experimental capture of the tip leakage vortex path and extension through the rotor passage. A comparison of the flow features with and without casing treatment was performed and the results are discussed against 3D viscous computational predictions. The casing treatment did not present any improvement of the compressor stall margin but no significant performance degradation was observed either. The CFD predictions showed a good agreement with the measurements and their analysis supported the experimental results.

Numerically Understand the Combined Effect of Tip Clearance and Circumferential Grooves Casing Treatment on the Performance of Single Stage Transonic Axial Flow Compressor

2015 ◽  
Author(s):  
Mitesh Goswami ◽  
Dilipkumar Bhanudasji Alone ◽  
Harish S. Choksi
Keyword(s):  
Axial Flow ◽  
Single Stage ◽  
Tip Clearance ◽  
Combined Effect ◽  
Stall Margin ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Circumferential Groove ◽  
Flow Compressor ◽  
Stage Efficiency

This paper deals with the numerical studies on the combined effect of tip clearance and axisymmetric circumferential grooves casing treatment (CGCT) on the overall performance and stall margin of a single stage transonic axial flow compressor. Steady state numerical analysis was carried out by solving three dimensional Reynolds-averaged-Navier-Stokes (RANS) Equations using the Shear Stress Transport (SST) k-ω Turbulence Model. The numerical stall inception point was identified from the last converged point by the convergence criteria, and the stall margin was numerically predicted. Additionally, the stall margin and the isentropic peak stage efficiencies of the circumferential casing grooves with various tip clearances were compared and evaluated in order to explore the influence of the tip clearance. Results obtained were compared with those obtained on the baseline compressor with the smooth casing (SC). Further computational studies were conducted to study the role of the tip leakage flow in axial compressor in triggering the stall. The relationship between the tip clearance flow, flow field and surge margin extension from circumferential groove casing treatment with various rotor tip clearances were studied numerically. The application of the circumferential groove casing treatment with varying clearance leads to significant improvement in the operating stability of compressor with slight reduction in the isentropic peak stage efficiency for small tip clearances, whereas there was slight increment in the isentropic peak stage efficiency at higher tip clearance of 2.5 mm.

Experimental Investigation of Circumferential Groove Casing Treatments for Large Tip Clearances in a Low Speed Axial Research Compressor

2015 ◽  
Author(s):  
Matthias Rolfes ◽  
Martin Lange ◽  
Konrad Vogeler
Keyword(s):  
Tip Clearance ◽  
Negative Effects ◽  
Low Speed ◽  
Operating Range ◽  
Circumferential Groove ◽  
Groove Configurations ◽  
And Performance ◽  
Casing Treatments ◽  
Operating Points ◽  
Probe Measurements

In high pressure compressors large tip clearances can occur in the rear stages especially during transient operation. This can lead to a reduced operating range and performance of the compressor. One simple means to reduce the negative effects of a rotor tip clearance increase can be circumferential groove casing treatments. Their ability to improve the operating range of a compressor is well-known for several decades. In this paper, an experimental study to investigate the influence of three different circumferential groove casing treatments on a low speed axial research compressor with very large rotor tip clearances (5% of annulus height) is presented. Two single-groove and one double-groove casing treatments have been tested. The grooves are positioned from 31% to 69% axial chord. The compressor characteristics of the smooth wall and the three groove configurations are discussed as well as selected five-hole probe measurements of the flow field downstream the rotor. It can be shown that all grooves are able to improve the operating range of the compressor. Furthermore, an improvement of efficiency due to the casing grooves can also be observed in certain operating points.

Self-Regulating Casing Treatment for Axial Compressor Stability Enhancement

2011 ◽  
Author(s):  
Stephanie Weichert ◽  
Ivor Day ◽  
Chris Freeman
Keyword(s):  
High Pressure ◽  
Treatment Effectiveness ◽  
Axial Compressor ◽  
Operating Conditions ◽  
Tip Clearance ◽  
The Self ◽  
Optimized Design ◽  
Stall Margin ◽  
Casing Treatment ◽  
Operating Range

The operating range of an axial compressor is often restricted by a safety imposed stall margin. One possible way of regaining operating range is with the application of casing treatment. Of particular interest here is the type of casing treatment which extracts air from a high pressure location in the compressor and re-injects it through discrete loops into the rotor tip region. Existing re-circulation systems have the disadvantage of reducing compressor efficiency at design conditions because worked flow is unnecessarily re-circulated at these operating conditions. Re-circulation is really only needed near stall. This paper proposes a self-regulating casing treatment in which the re-circulated flow is minimized at compressor design conditions and maximized near stall. The self-regulating capability is achieved by taking advantage of changes which occur in the tip clearance velocity and pressure fields as the compressor is throttled toward stall. In the proof-of-concept work reported here, flow is extracted from the high pressure region over the rotor tips and re-injected just upstream of the same blade row. Parametric studies are reported in which the flow extraction and re-injection ports are optimized for location, shape and orientation. The optimized design is shown to compare favorably with a circumferential groove tested in the same compressor. The relationship between stall inception type and casing treatment effectiveness is also investigated. The self-regulating aspect of the new design works well: stall margin improvements from 2.2 to 6.0% are achieved for just 0.25% total air re-circulated near stall and half that near design conditions. The self-regulating capability is achieved by the selective location and orientation of the extraction hole; a simple model is discussed which predicts the optimum axial location.

Interaction of Rotor and Casing Treatment Flow in an Axial Single-Stage Transonic Compressor With Circumferential Grooves

2008 ◽  
Author(s):  
Martin W. Mu¨ller ◽  
Christoph Biela ◽  
Heinz-Peter Schiffer ◽  
Chunill Hah
Keyword(s):  
Flow Field ◽  
Pressure Sensors ◽  
Rotating Stall ◽  
Operating Conditions ◽  
Single Stage ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Casing Treatment ◽  
Tip Leakage ◽  
Transonic Compressor

The influence of circumferential grooves on the tip flow field of an axial single-stage transonic compressor rotor has been examined experimentally and numerically. The compressor stage provides a strongly increased stall margin with only small penalties in efficiency when the casing treatment is applied. Due to the complex interactions of the grooves with the rotor flow, unsteady measurement techniques have been chosen as an attempt to identify the aerodynamic effects responsible for the operating range extension. Therefore, the casing treatment has been instrumented with piezoresistive pressure sensors in the land between the grooves providing high-resolution static wall pressure measurements at different operating conditions. Data acquisition worked at a sampling rate of 125kHz, providing around 23 static pressure values per blade passage at 11 axial positions at the nominal speed of 20,000 rpm. A comparable dataset, but with 14 sensors, was obtained for the smooth casing. The results show the fluctuation of the tip leakage vortex and shock-vortex-interactions as well as the changed situation with casing treatment. Ensemble-averaged data shows tip leakage vortex trajectories. At near stall conditions with the smooth casing, the vortex hits the front part of the adjacent blade, which indicates the possibility of a spill forward of low momentum fluid into the next passage. Standard deviation values prove a high fluctuation of the pressure field over the tip gap. When the casing treatment is applied, the vortex trajectory maintains alignment along the blade’s suction side, thus preventing the onset of rotating stall. Results are presented as a back-to-back comparison of the smooth casing versus the treated casing at three operating conditions: peak efficiency at a mass flow rate of m˙pe = 16.2kg/s, near stall of the smooth casing at m˙nssc = 14.0kg/s and near stall of the treated casing at m˙ns = 12.6kg/s. Steady and unsteady numerical simulations of the rotor-only flow field have been calculated with and without grooves. These calculations aim at a broad analysis of the occurring flow phenomena at the rotor tip. Tip leakage flow behaviour and vortex trajectories are discussed in detail by summarizing the congruent findings of both numerical and experimental investigations.

scholarly journals Flow Field Investigation in the Exit Region of a Radial Inflow Turbine Using LDV

1994 ◽  
Author(s):  
D. Muthuvel Murugan ◽  
Widen Tabakoff ◽  
Awatef Hamed
Keyword(s):  
Flow Field ◽  
Field Investigation ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Complex Flow ◽  
Tip Clearance Flow ◽  
Exit Region ◽  
Flow Investigation ◽  
Clearance Flow ◽  
Radial Inflow Turbine

Detailed flow investigation in the downstream region of a radial inflow turbine has been performed using a three component Laser Doppler Velocimetry. The flow velocities are measured in the exit region of the turbine at off-design operating conditions. The results are presented as contour and vector plots of mean velocities, flow angles and turbulent stresses. The measured parameters are correlated to the rotor blade rotation to observe any periodic nature of the flow. The measurements reveal a complex flow pattern near the tip region at the rotor exit due to the interaction of the tip clearance flow. The degree of swirl of the flow near the tip region at the rotor exit is observed to be high due to the gross under turning of the flow near the tip region. The effect of the rotor on the exit flow field is observed in the proximity of the rotor exit.

An Impact of Self-Recirculation Casing Treatment (SRCT) Configurations on Impeller Stall Margin and the Flow Field

2012 ◽  
Author(s):  
Yan Ma ◽  
Guang Xi ◽  
Guangkuan Wu
Keyword(s):  
Flow Field ◽  
High Speed ◽  
Operating Conditions ◽  
Centrifugal Impeller ◽  
Flow Angle ◽  
Stall Margin ◽  
Casing Treatment ◽  
Swirl Velocity ◽  
Inlet Swirl ◽  
Unsteady Simulation

The present paper describes an investigation of stall margin enhancement and a detailed analysis of the impeller flow field due to self-recirculation casing treatment (SRCT) configuration of a high-speed small-size centrifugal impeller. The influence of different SRCT configurations on the impeller flow field at near-stall condition has been analyzed, highlighting the improvement in stall flow ability. This paper also discusses the influence of the SRCT configurations on the inlet flow angle, inlet swirl velocity and loss distribution in the impeller passage to understand the mechanism of the SRCT configurations in enhancing the stall margin of the impeller. The variation of the bleed flow rate at different operating conditions is also presented in this paper. Finally, the time-averaged unsteady simulation results at near-stall point are presented and compared with steady-state solutions.

Tip Clearance Flow Induced Endwall Boundary Layer Separation in a Single–Stage Axial–Flow Low–Speed Compressor

2000 ◽  
Author(s):  
Horst Saathoff ◽  
Udo Stark
Keyword(s):  
Axial Flow ◽  
Boundary Layer Separation ◽  
Single Stage ◽  
Tip Clearance ◽  
Compressor Cascade ◽  
Tip Clearance Flow ◽  
Low Speed ◽  
Pressure Distributions ◽  
Oil Flow ◽  
Clearance Flow

The paper describes an investigation of the overtip end-wall flow in a single–stage axial–flow low–speed compressor utilizing an oil flow technique and a periodic multisampling pressure measurement technique. Representative oil flow pictures and ensemble averaged casingwall pressure distributions with standard deviations — supplemented by selected endwall oil flow pictures from a corresponding 2D compressor cascade — are shown and carefully analysed. The results enable the key features of the overtip endwall flow to be identified and changes with flow rate — or inlet angle — to be determined.

Sign in / Sign up

Export Citation Format

Share Document