Experimental and Numerical Investigation of a Circumferential Groove Casing Treatment in a Low-Speed Axial Research Compressor at Different Tip Clearances

2017 ◽  
Vol 139 (12) ◽  
Author(s):  
Matthias Rolfes ◽  
Martin Lange ◽  
Konrad Vogeler ◽  
Ronald Mailach
Keyword(s):  
Total Pressure ◽  
Solid Wall ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Chord Length ◽  
Single Stage ◽  
Low Speed ◽  
Casing Treatment ◽  
Operating Range ◽  
Circumferential Groove

The demand of increasing pressure ratios for modern high pressure compressors leads to decreasing blade heights in the last stages. As tip clearances (TC) cannot be reduced to any amount and minimum values might be necessary for safety reasons, the TC ratios of the last stages can reach values notably higher than current norms. This can be intensified by a compressor running in transient operations where thermal differences can lead to further growing clearances. For decades, the detrimental effects of large clearances on an axial compressor's operating range and efficiency are known and investigated. The ability of circumferential casing grooves in the rotor casing to improve the compressor's operating range has also been in the focus of research for many years. Their simplicity and ease of installation are one reason for their continuing popularity nowadays, where advanced methods to increase the operating range of an axial compressor are known. In the authors' previous paper, three different circumferential groove casing treatments were investigated in a single-stage environment in the low-speed axial research compressor at TU Dresden. One of these grooves was able to notably improve the operating range and the efficiency of the single stage compressor at very large rotor TC (5% of chord length). In this paper, the results of tests with this particular groove type in a three stage environment in the low-speed axial research compressor are presented. Two different rotor TC sizes of 1.2% and 5% of tip chord length were investigated. At the small TC, the grooves are almost neutral. Only small reductions in total pressure ratio and efficiency compared to the solid wall can be observed. If the compressor runs with large TC, it notably benefits from the casing grooves. Both, total pressure and efficiency can be improved by the grooves in a similar extent as in single stage tests. Five-hole probe measurements and unsteady wall pressure measurements show the influence of the groove on the flow field. With the help of numerical investigations, the different behavior of the grooves at the two TC sizes will be discussed.

Experimental and Numerical Investigation of a Circumferential Groove Casing Treatment in a Low Speed Axial Research Compressor at Different Tip Clearances

2017 ◽  
Author(s):  
Matthias Rolfes ◽  
Martin Lange ◽  
Konrad Vogeler ◽  
Ronald Mailach
Keyword(s):  
Total Pressure ◽  
Solid Wall ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Chord Length ◽  
Single Stage ◽  
Tip Clearance ◽  
Low Speed ◽  
Operating Range ◽  
Circumferential Groove

The demand of increasing pressure ratios for modern high pressure compressors leads to decreasing blade heights in the last stages. As tip clearances cannot be reduced to any amount and minimum values might be necessary for safety reasons, the tip clearance ratios of the last stages can reach values notably higher than current norms. This can be intensified by a compressor running in transient operations where thermal differences can lead to further growing clearances. For decades, the detrimental effects of large clearances on an axial compressor’s operating range and efficiency are known and investigated. The ability of circumferential casing grooves in the rotor casing to improve the compressor’s operating range has also been in the focus of research for many years. Their simplicity and ease of installation are one reason for their continuing popularity nowadays, where advanced methods to increase the operating range of an axial compressor are known. In a previous paper [1], three different circumferential groove casing treatments were investigated in a single stage environment in the Low Speed Axial Research Compressor at TU Dresden. One of these grooves was able to notably improve the operating range and the efficiency of the single stage compressor at very large rotor tip clearances (5% of chord length). In this paper, the results of tests with this particular groove type in a three stage environment in the Low Speed Axial Research Compressor are presented. Two different rotor tip clearance sizes of 1.2% and 5% of tip chord length were investigated. At the small tip clearance, the grooves are almost neutral. Only small reductions in total pressure ratio and efficiency compared to the solid wall can be observed. If the compressor runs with large tip clearances it notably benefits from the casing grooves. Both, total pressure and efficiency can be improved by the grooves in a similar extent as in single stage tests. Five-hole probe measurements and unsteady wall pressure measurements show the influence of the groove on the flow field. With the help of numerical investigations the different behavior of the grooves at the two tip clearance sizes will be discussed.

scholarly journals Investigation of Performance and Rotor Tip Flow Field in a Low Speed Research Compressor with Circumferential Groove Casing Treatment at Varying Tip Clearance

2017 ◽  
Vol 2017 ◽  
pp. 1-14 ◽  
Author(s):  
Matthias Rolfes ◽  
Martin Lange ◽  
Ronald Mailach
Keyword(s):  
Flow Field ◽  
Operating Conditions ◽  
Single Stage ◽  
Tip Clearance ◽  
Experimental Investigations ◽  
Low Speed ◽  
Pressure Transducers ◽  
Casing Treatment ◽  
Operating Range ◽  
Circumferential Groove

Experimental investigations in a single-stage low speed axial research compressor are presented. The influence of four different rotor tip clearances on the overall compressor performance and on the rotor tip flow field is investigated in configurations with and without circumferential groove casing treatments. Piezo-resistive pressure transducers are used to capture the unsteady flow field in the rotor tip region. The investigated casing groove is effectively working at the three largest investigated tip clearance sizes. The largest achieved operating range increase by the groove is 6.9%. The groove can delay the upstream movement of the flow interface between leakage flow and main flow and thus increase the stable operating range. Rotating instabilities are shown to exist at large tip clearance sizes in throttled operating conditions. Their amplitudes can be damped by the casing groove. No modal activities could be detected in the current single-stage compressor build.

Experimental Investigation of the Steady and Unsteady Flow Field in a Single Stage Low Pressure Axial Compressor With a Circumferential Groove Casing Treatment

2010 ◽  
Author(s):  
N. Van de Wyer ◽  
B. Farkas ◽  
J. Desset ◽  
J. F. Brouckaert ◽  
J.-F. Thomas ◽  
...  
Keyword(s):  
Experimental Investigation ◽  
Flow Field ◽  
Unsteady Flow ◽  
Axial Compressor ◽  
Low Pressure ◽  
Fast Response ◽  
Single Stage ◽  
Compressor Stage ◽  
Casing Treatment ◽  
Circumferential Groove

This paper deals with the experimental investigation of the influence of a circumferential groove casing treatment on the performance and stability margin of a single stage low pressure axial compressor. The design of the compressor stage is representative of a booster stage for the new counter-rotating turbofan engine architecture and is characterized by unusually high loading and flow coefficients. The choice of the circumferential groove is described on the basis of a numerical parametric study on the number of grooves, the axial position, the depth and width of the groove. The experiments were performed at a Reynolds number corresponding to cruise conditions in the von Karman Institute closed loop high speed compressor test rig R4. The detailed performance characterization of the compressor stage with casing treatment was mapped at four operating points from choke to stall at design speed. The compressor stall limit was determined at several other off-design speeds. Detailed steady and unsteady measurements were performed to determine the flow field characteristics of the rotor and of the complete stage. Conventional pressure, temperature and directional probes were used along with fast response pressure sensors in the rotor casing and in the groove. Simultaneous traverses with a fast response total pressure probe were used to map the unsteady flow field at the rotor exit allowing an experimental capture of the tip leakage vortex path and extension through the rotor passage. A comparison of the flow features with and without casing treatment was performed and the results are discussed against 3D viscous computational predictions. The casing treatment did not present any improvement of the compressor stall margin but no significant performance degradation was observed either. The CFD predictions showed a good agreement with the measurements and their analysis supported the experimental results.

Combined Effects of Forward Sweep and Tip Clearance on the Performance of Axial Flow Compressor Stage

2009 ◽  
Author(s):  
P. V. Ramakrishna ◽  
M. Govardhan
Keyword(s):  
Total Pressure ◽  
Axial Compressor ◽  
Axial Flow ◽  
Pressure Rise ◽  
Tip Clearance ◽  
Numerical Work ◽  
Low Speed ◽  
Operating Range ◽  
Axial Flow Compressor ◽  
Flow Compressor

There are a number of performance indices for a turbomachine on the basis of which its strength is evaluated. In the case of axial compressors, pressure ratio, efficiency and stall margin are few such indices which are of major concern in the design phase as well as in the evaluation of performance of the machine. In the process of improving the blade design, 3D blade stacking, where the aerofoil sections constituting the blade are moved in relation to the flow. Tilting the blade sections to the flow direction (blade sweep) would increase the operating range of an axial compressor due to modifications in the pressure and velocity fields on the suction surface. On the other hand, blade tip gap, though finite, has great influence on the performance of a turbomachine. The present work investigates the combined effect of these two factors on various flow characteristics in a low speed axial flow compressor. The objective of the present paper is thereby confined to study the collective effects of sweep and tip clearance without attempting to suggest an outright new design. In the present numerical work, the performance of Tip Chordline Sweeping (TCS) and Axial Sweeping (AXS) of low speed axial compressor rotor blades are studied. For this, 15 computational domains were modeled for five rotor sweep configurations and three different clearance levels for each rotor. Through the results, 20°AXS rotor is found to be distinctive among all the rotors with highest pressure rise, higher operating range and less tip clearance loss characteristics. TCS rotors produced improved total pressure rise at the low flow coefficients when the tip gap is increased. Hence there is a chance that an “optimum” tip gap exists for the TCS rotors in terms of total pressure coefficient and operating range, while AXS rotors are at their best with the minimum possible clearance.

scholarly journals Stability Enhancement of a Single-Stage Transonic Axial Compressor Using Inclined Oblique Slots

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2346
Author(s):  
Tien-Dung Vuong ◽  
Kwang-Yong Kim
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Single Stage ◽  
Rotor Blades ◽  
Navier Stokes ◽  
Optimized Design ◽  
Stall Margin ◽  
Casing Treatment ◽  
Transonic Axial Compressor

A casing treatment using inclined oblique slots (INOS) is proposed to improve the stability of the single-stage transonic axial compressor, NASA Stage 37, during operation. The slots are installed on the casing of the rotor blades. The aerodynamic performance was estimated using three-dimensional steady Reynolds-Averaged Navier-Stokes analysis. The results showed that the slots effectively increased the stall margin of the compressor with slight reductions in the pressure ratio and adiabatic efficiency. Three geometric parameters were tested in a parametric study. A single-objective optimization to maximize the stall margin was carried out using a Genetic Algorithm coupled with a surrogate model created by a radial basis neural network. The optimized design increased the stall margin by 37.1% compared to that of the smooth casing with little impacts on the efficiency and pressure ratio.

A Study of Influences of Inlet Total Pressure Distortions On Clearance Flow in an Axial Compressor

2021 ◽  
Author(s):  
Guoming Zhu ◽  
Xiaolan Liu ◽  
Bo Yang ◽  
Moru Song
Keyword(s):  
Total Pressure ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Leading Edge ◽  
Stall Margin ◽  
Flow Cells ◽  
Static Pressure Distribution ◽  
Speed Flow ◽  
Clearance Flow ◽  
The Stability

Abstract The rotating distortion generated by upstream wakes or low speed flow cells is a kind of phenomenon in the inlet of middle and rear stages of an axial compressor. Highly complex inflow can obviously affect the performance and the stability of these stages, and is needed to be considered during compressor design. In this paper, a series of unsteady computational fluid dynamics (CFD) simulations is conducted based on a model of an 1-1/2 stage axial compressor to investigate the effects of the distorted inflows near the casing on the compressor performance and the clearance flow. Detailed analysis of the flow field has been performed and interesting results are concluded. The distortions, such as total pressure distortion in circumferential and radial directions, can block the tip region so that the separation loss and the mixing loss in this area are increased, and the efficiency and the total pressure ratio are dropped correspondingly. Besides, the distortions can change the static pressure distribution near the leading edge of the rotor, and make the clearance flow spill out of the rotor edge more easily under near stall condition, especially in the cases with co-rotating distortions. This phenomenon can be used to explain why the stall margin is deteriorated with nonuniform inflows.

Stall Warning Using the Rotor Tip Pressure in a Transonic Axial Compressor With Circumferential Grooves

2018 ◽  
Author(s):  
Byeung Jun Lim ◽  
Tae Choon Park ◽  
Young Seok Kang
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Axial Compressor ◽  
Rotating Stall ◽  
Single Stage ◽  
Stall Inception ◽  
Casing Treatment ◽  
Stall Warning ◽  
Transonic Axial Compressor

In this study, characteristics of stall inception in a single-stage transonic axial compressor with circumferential grooves casing treatment were investigated experimentally. Additionally, the characteristic of increasing irregularity in the pressure inside circumferential grooves as the compressor approaches the stall limit was applied to the stall warning method. Spike-type rotating stall was observed in the single-stage transonic axial compressor with smooth casing. When circumferential grooves were applied, the stall inception was suppressed and the operating point of the compressor moved to lower flow rate than the stall limit. A spike-like disturbance was developed into a rotating stall cell and then the Helmholtz perturbation was overlapped on it at N = 80%. At N = 70 %, the Helmholtz perturbation was observed first and the amplitude of the wave gradually increased as mass flow rate decreased. At N = 60%, spike type stall inceptions were observed intermittently and then developed into continuous rotating stall at lower mass flow rate. Pressure measured at the bottom of circumferential grooves showed that the level of irregularity of pressure increased as flow rate decreased. Based on the characteristic of increasing irregularity of the pressure signals inside the circumferential grooves as stall approaches, an autocorrelation technique was applied to the stall warning. This technique could be used to provide warning against stall and estimate real-time stall margins in compressors with casing treatments.

Numerical Efforts of Aerodynamic Re-Design in a Single-Stage Transonic Axial Compressor: Part 1 — Stator Design

2017 ◽  
Author(s):  
Justin (Jongsik) Oh
Keyword(s):  
Pressure Ratio ◽  
Axial Compressor ◽  
Axial Flow ◽  
Single Stage ◽  
Design Flow ◽  
Design Parameters ◽  
Original Design ◽  
Circular Arc ◽  
Surge Margin ◽  
Flow Compressor

In many aerodynamic design parameters for the axial-flow compressor, three variables of tailored blading, blade lean and sweep were considered in the re-design efforts of a transonic single stage which had been designed in 1960’s NASA public domains. As Part 1, the re-design was limited to the stator vane only. For the original MCA (Multiple Circular Arc) blading, which had been applied at all radii, the CDA (Controlled Diffusion Airfoil) blading was introduced at midspan as the first variant, and the endwalls of hub and casing (or tip) were replaced with the DCA (Double Circular Arc) blading for the second variant. Aerodynamic performance was predicted through a series of CFD analysis at design speed, and the best aerodynamic improvement, in terms of pressure ratio/efficiency and operability, was found in the first variant of tailored blading. It was selected as a baseline for the next design efforts with blade lean, sweep and both combined. Among 12 variants, a case of positively and mildly leaned blades was found the most attractive one, relative to the original design, providing benefits of an 1.0% increase of pressure ratio at design flow, an 1.7% increase of efficiency at design flow, a 10.5% increase of the surge margin and a 32.3% increase of the choke margin.

Sign in / Sign up

Export Citation Format

Share Document