scholarly journals Formation and Properties of the Ta-Y2O3, Ta-ZrO2, and Ta-TaC Nanocomposites

2018 ◽  
Vol 2018 ◽  
pp. 1-12
Author(s):  
J. Jakubowicz ◽  
M. Sopata ◽  
G. Adamek ◽  
P. Siwak ◽  
T. Kachlicki
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Mechanical Alloying ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Ceramic Composites ◽  
Ceramic Phase ◽  
Plasma Sintering ◽  
Average Grain Size ◽  
Bulk Nanocrystalline

The nanocrystalline tantalum-ceramic composites were made using mechanical alloying followed by pulse plasma sintering (PPS). The tantalum acts as a matrix, to which the ceramic reinforced phase in the concentration of 5, 10, 20, and 40 wt.% was introduced. Oxides (Y2O3 and ZrO2) and carbides (TaC) were used as the ceramic phase. The mechanical alloying results in the formation of nanocrystalline grains. The subsequent hot pressing in the mode of PPS results in the consolidation of powders and formation of bulk nanocomposites. All the bulk composites have the average grain size from 40 nm to 100 nm, whereas, for comparison, the bulk nanocrystalline pure tantalum has the average grain size of approximately 170 nm. The ceramic phase refines the grain size in the Ta nanocomposites. The mechanical properties were studied using the nanoindentation tests. The nanocomposites exhibit uniform load-displacement curves indicating good integrity and homogeneity of the samples. Out of the investigated components, the Ta-10 wt.% TaC one has the highest hardness and a very high Young’s modulus (1398 HV and 336 GPa, resp.). For the Ta-oxide composites, Ta-20 wt.% Y2O3 has the highest mechanical properties (1165 HV hardness and 231 GPa Young’s modulus).

Mechanical properties of FeAlSi powders prepared by mechanical alloying from different initial feedstock materials

2019 ◽  
Vol 107 (2) ◽  
pp. 207 ◽  
Author(s):  
Jaroslav Čech ◽  
Petr Haušild ◽  
Miroslav Karlík ◽  
Veronika Kadlecová ◽  
Jiří Čapek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Alloying ◽  
Young’S Modulus ◽  
Milling Time ◽  
Young's Modulus ◽  
Element Model ◽  
X Ray Diffraction ◽  
X Ray ◽  
Powder Particles ◽  
Complete Homogenization

FeAl20Si20 (wt.%) powders prepared by mechanical alloying from different initial feedstock materials (Fe, Al, Si, FeAl27) were investigated in this study. Scanning electron microscopy, X-ray diffraction and nanoindentation techniques were used to analyze microstructure, phase composition and mechanical properties (hardness and Young’s modulus). Finite element model was developed to account for the decrease in measured values of mechanical properties of powder particles with increasing penetration depth caused by surrounding soft resin used for embedding powder particles. Progressive homogenization of the powders’ microstructure and an increase of hardness and Young’s modulus with milling time were observed and the time for complete homogenization was estimated.

Fabrication of Titanium / Biodegradable-Polymer FGM for Medical Application

2009 ◽  
Vol 631-632 ◽  
pp. 199-204 ◽  
Author(s):  
Yoshimi Watanabe ◽  
Yoshimi Iwasa ◽  
Hisashi Sato ◽  
Akira Teramoto ◽  
Koji Abe
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Medical Application ◽  
Hot Water ◽  
Porous Ti ◽  
Ti Alloys ◽  
Plasma Sintering ◽  
Biodegradable Poly ◽  
Spark Plasma

Ti and Ti alloys are widely used as metallic implants, because of their good mechanical properties and nontoxic behavior. However, they have problems as the implant-materials, namely, high Young’s modulus comparing that of bone and low bonding ability with bone. There is a need to develop the Ti and Ti alloys with lower Young’s modulus and good bonding ability. In previous study, Ti composite containing biodegradable poly-L-lactic-acid (PLLA) fiber has been fabricated to improve these problems. However, this composite has low strength because of the imperfect sintering of Ti matrix. To improve its strength, sintering of Ti matrix should be completed. In this study, Ti-NaCl composite material was fabricated by spark plasma sintering (SPS) method using powder mixture of Ti and NaCl to complete the sintering of Ti matrix. To obtain porous Ti samples, Ti-NaCl composite were put into hot water of 100 oC. The porous Ti was dipped into PLLA melt in order to introduce PLLA into the pores of porous Ti. Finally, Ti-PLLA composite was obtained, and PLLA plays a role as reinforcement of Ti matrix. It was found that the Ti-PLLA composite has gradient structure and mechanical properties.

Mechanical Properties and Machinability of Si3N4/hBN Composites Prepared by Pressureless Sintering

2006 ◽  
Vol 510-511 ◽  
pp. 1014-1017 ◽  
Author(s):  
Won Seung Cho ◽  
Ki Ju Lee ◽  
Myeong Woo Cho ◽  
Jae Hyung Lee ◽  
Woon Suk Hwang
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Ceramic Composites ◽  
Pressureless Sintering ◽  
Si3n4 Ceramic ◽  
Cutting Resistance ◽  
Axis Parallel ◽  
Si3n4 Ceramics

The effects of hBN content on microstructure, mechanical properties, and machinability of the pressureless-sintered Si3N4 ceramics were investigated. Flexural strength, Young’s modulus, and hardness decreased with increasing h-BN content. The mechanical properties are decreased mainly because of increased porosity of composite, and the much lower Young's modulus of BN compared to that of Si3N4. Pressureless-sintered Si3N4/hBN composites exhibit strong texture of BN grains oriented with the c-axis parallel to the cold-pressing direction. Cutting resistance of Si3N4 ceramic composites with more than 10 vol% hBN decreased with increasing hBN content, demonstrating a good machinability of the composites. The residual pores can be attributed to improved machinability of pessureless-sintered Si3N4-BN composite.

Effect of Sintering Temperature on Microstructure and Mechanical Properties of Nanocrystalline Aluminum 5083 Alloy

2015 ◽  
Vol 782 ◽  
pp. 113-118
Author(s):  
Ying Mei Teng ◽  
Zhao Hui Zhang ◽  
Zi Zhou Yuan
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Compressive Strength ◽  
Sintering Temperature ◽  
Initial Pressure ◽  
Fine Grain ◽  
Microstructure And Mechanical Properties ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Bulk Nanocrystalline

The bulk nanocrystalline (NC) aluminum (Al) 5083 was synthesized by spark plasma sintering (SPS) technique with low initial pressure of 1 MPa, high holding pressure of 300 MPa and holding time of 4 min at different sintering temperatures, using surface passivated nanopowders. The effect of sintering temperature on microstructure and mechanical properties of the bulk NC Al 5083 were investigated. Results indicate that the density, grain size, the hardness and the compressive strength of the bulk NC Al 5083 increase with an increase in sintering temperature. The mechanical properties of the material are greatly improved due to the fine grain size. The bulk NC Al 5083 sintered at 723 K has the highest micro-hardness of 2.37 GPa and the best compressive strength of 845 MPa.

Densification Behaviour and Mechanical Properties on MgO Doped Zirconia Toughened Alumina (ZTA) Prepared by Two-Stage Sintering

2021 ◽  
Vol 1030 ◽  
pp. 3-10
Author(s):  
Teow Hsien Loong ◽  
Ananthan Soosai ◽  
Suresh Muniandy
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Grain Size ◽  
Total Hip Arthroplasty ◽  
Young’S Modulus ◽  
Vickers Hardness ◽  
Young's Modulus ◽  
Two Stage ◽  
Positive Effect ◽  
Zirconia Toughened Alumina

The effect of doping small amounts of Magnesium Oxide ranging between 0 to 1 vol% on Zirconia Toughened Alumina (ZTA) composites which is one of main biomaterial used for production of total hip arthroplasty were investigated. The samples were produced via conventional two-stage sintering with T1 varies between 1450°C and 1550°C with heating rate of 20°C/min. The samples were then rapid cooled to T2 set at 1400°C with holding time of 12 hours. The microstructural and mechanical properties of the two-stage sintered ZTA are then investigated to determine the feasibility of MgO addition. Combination of two-stage sintering at T1 above 1500 and also small amount of MgO up to 0.5 vol% were shown to have positive effect on ZTA which exhibited improvement on its grain size, mechanical properties such as Vickers hardness, Young’s modulus and fracture toughness compared to undoped ZTA composites. The sample with 0.5 vol% MgO addition sintered at T1 of 1500°C and T2 1400°C was able to achieve Vickers hardness of 19.6 GPa, Young’s modulus of 408 GPa and fracture toughness of 6.8 MPam1/2 without significant grain growth compared to undoped ZTA composites.

Thermal Cycling Effect on Mechanical Properties, Grain Size and Residual Stress in Alumina and Yttria-Stabilized Tetragonal Zirconia

2014 ◽  
Vol 875-877 ◽  
pp. 1642-1646
Author(s):  
Jing Zhang
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Grain Size ◽  
Thermal Cycling ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Tetragonal Zirconia ◽  
Thermal Cycles ◽  
Optical Applications ◽  
Increasing Temperature

Alumina and zirconia are important materials for energy and optical applications. In this study, the effect of thermal cycling on grain size and residual stress was reported. Residual stress was measured using X-ray diffraction (XRD) sin2ψ method for the as-received and the samples after thermal cycling up to 900 cycles. For alumina, the measured residual stress is approximately 96 MPa in tensile for the as-received material, and increases to its highest value of 480 MPa after 650 thermal cycles. The residual stress decreases from 480 MPa to 96 MPa in tensile with increased thermal cycling from 650 to 900 cycles. The crystallized grain size calculated from the diffraction pattern shows that the mean crystallized grain size is about 93 nm for the as-received and increases to 232 nm after 650 thermal cycles. This result is consistent with the enlarged grain size observed by scanning electron microscopy for the alumina after 650 thermal cycles reported earlier. With continued thermal cycling up to 900 cycles, the crystallized grain size is greatly reduced to 104 nm. It suggests that evolution of the crystallized grain size is correlated with the residual stress. For yttria-stabilized tetragonal zirconia (Y-TZP), the mechanical properties at room temperature, are consistent with the property values provided by the manufacturer. The Young’s modulus of shows a non-linear inverse relationship with increasing temperature. The degradation of the Young’s modulus mostly occurs prior to 400 °C and to a less extent in the temperature range of 400 °C up to 850 °C. The Vickers hardness number for the as-received Y-TZP material decreases to a very small extent after 560 thermal cycles and increases approximately 2%, after 1200 thermal cycles. This is consistent with the trend of the Young’s modulus for thermal-cycled specimens.

Mechanical Properties of ECAE Nanocrystalline Copper and Nickel

2005 ◽  
Vol 23 ◽  
pp. 183-186 ◽  
Author(s):  
S. Bansal ◽  
A.M. Saxena ◽  
T. Hartwig ◽  
Rao R. Tummala
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Grain Size ◽  
Tensile Strength ◽  
High Purity ◽  
Bulk Sample ◽  
Nanocrystalline Copper ◽  
Average Grain Size ◽  
Angular Extrusion ◽  
Bulk Nanocrystalline

Bulk nanocrystalline copper and nickel (average grain size ~ 50 nm) with high purity and density were synthesized by equichannel angular extrusion (ECAE). Both nanohardness and microhardness measurements revealed a significant increase in hardness of the bulk sample. The tensile strength of these materials has been found to be 5-6 times higher than conventional forms and our experiments show that Cu is extremely stable up to temperatures of 100 oC and Ni to temperatures of 250 oC. The fracture toughness, measured by the value of JIC for nc-copper and nickel have been found to be 21.66 KJ/m2 and 12.13 KJ/m2, respectively which are high for these strength levels.

Densification, Microstructure, and Behavior of Hydroxyapatite Ceramics Sintered by Using Spark Plasma Sintering

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Shufeng Li ◽  
Hiroshi Izui ◽  
Michiharu Okano
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Young’S Modulus ◽  
Spark Plasma Sintering ◽  
Young's Modulus ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Temperature And Pressure

This paper discusses the dependence of the mechanical properties and microstructure of sintered hydroxyapatite (HA) on the sintering temperature and pressure. A set of specimens was prepared from as-received HA powder and sintered by using a spark plasma sintering (SPS) process. The sintering pressures were set at 22.3MPa, 44.6MPa, and 66.9MPa, and sintering was performed in the temperature range from 800°Cto1000°C at each pressure. Mechanisms underlying the interrelated temperature-mechanical and pressure-mechanical properties of dense HA were investigated. The effects of temperature and pressure on the flexural strength, Young’s modulus, fracture toughness, relative density, activation energy, phase stability, and microstructure were assessed. The relative density and grain size increased with an increase in the temperature. The flexural strength and Young’s modulus increased with an increase in the temperature, giving maximum values of 131.5MPa and 75.6GPa, respectively, at a critical temperature of 950°C and 44.6MPa, and the fracture toughness was 1.4MPam1∕2 at 1000°C at 44.6MPa. Increasing the sintering pressure led to acceleration of the densification of HA.

The hardness and Young's modulus of bulk YBa2Cu3O7−x (1:2:3) and YBa2Cu4O8 (1:2:4) as determined by ultra low load indentation

1991 ◽  
Vol 6 (12) ◽  
pp. 2519-2522 ◽  
Author(s):  
B.N. Lucas ◽  
W.C. Oliver ◽  
R.K. Williams ◽  
J. Brynestad ◽  
M.E. O'Hern
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Young’S Modulus ◽  
Thermal Stresses ◽  
Young's Modulus ◽  
Thermal Expansion Data ◽  
Spatially Resolved ◽  
Bulk Superconductors ◽  
Current Densities ◽  
Critical Grain Size

Using a highly-spatially-resolved mechanical properties microprobe, the Young's modulus and hardness of bulk YBa2Cu3O7−x (1:2:3) and YBa2Cu4O8 (1:2:4) have been determined. The Young's modulus of a superconductor is an important parameter in determining critical grain sizes above which microcracking will occur due to anisotropic thermal stresses that arise during processing. This phenomenon of microcracking has been determined to cause a decrease in the attainable critical current densities in bulk superconductors. The mechanical properties data for these two materials show that the Young's modulus of 1:2:3 is approximately 35% greater than the modulus of 1:2:4. This along with available anisotropic thermal expansion data for 1:2:3 and 1:2:4 suggests that the critical grain size for 1:2:4 is about 7 times greater than the critical grain size for microcracking in 1:2:3.

Young’s Modulus of Polysilicon Thin Film Evaluated by Finite Element Analysis

2007 ◽  
Vol 353-358 ◽  
pp. 2227-2230
Author(s):  
Kazuto Tanaka ◽  
Kohji Minoshima ◽  
Takehiro Imoto
Keyword(s):  
Thin Film ◽  
Grain Size ◽  
Finite Element ◽  
Young’S Modulus ◽  
Crystal Orientation ◽  
Young's Modulus ◽  
Fem Analysis ◽  
Front Surface ◽  
Element Analysis ◽  
Average Grain Size

To analyze the effect of the crystal orientations and the grain size on the Young's modulus of thin polysilicon microelements, two-dimensional finite element models in plain strain condition were developed using a Voronoi structure. The number of grains in a model of a 10 μm square area was changed from 23 to 1200. The grain size and the crystal orientation of the film were analyzed by means of an electron back-scattering diffraction pattern (EBSP) method. The average grain size of the front surface of the thin film was about 0.69 μm, which is almost equal to the grain size of the Voronoi model having 300 grains. From the results of EBSP analysis, the specimen had no oriented structure. Therefore, random crystal orientation was given to each grain of the FEM models. When the number of grains increased, the Young's modulus converged on about 171 GPa and its scatter caused by the different sets of the random orientation was reduced. The Young's modulus obtained by the FEM analysis was larger than the value obtained by the tensile tests.

Sign in / Sign up

Export Citation Format

Share Document