scholarly journals Mechanical Modeling of Frozen Coarse-Grained Materials Incorporating Microscale Investigation

2021 ◽  
Vol 2021 ◽  
pp. 1-16
Author(s):  
Shan-Zhen Li ◽  
Liang Tang ◽  
Shuang Tian ◽  
Xian-Zhang Ling ◽  
Yang-Sheng Ye ◽  
...  
Keyword(s):  
Strain Softening ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Coarse Grained ◽  
Peak Strain ◽  
Compression Tests ◽  
Engineering Structures ◽  
Softening Behavior ◽  
Coarse Grained Material ◽  
Predicted Values

In the cold regions of China, coarse-grained materials are frequently encountered or used as backfilling materials in infrastructure construction, such as dams, highways, railways, and mineral engineering structures. Effects of confining pressure (0.2, 0.5, and 1 MPa) and frozen temperature (−2, −5, −10, and −15°C) on the stress-strain response and elastic modulus were investigated using triaxial compression tests. Moreover, the microscale structures of a coarse-grained material were obtained by X-ray computed tomography. The coarse-grained material specimens exhibited strain-softening and significant dilatancy behaviors during shearing. A modified model considering microstructures of the material was proposed to describe these phenomena. The predicted values coincided well with the experimental results obtained in this study and other literatures. The sensitivity analysis of parameters indicated that the model can simulate the initial hardening and post-peak strain-softening behavior of soils. And the transition of volume strain from contraction to dilatancy can also be described using this model. The results obtained in this study can provide a helpful reference for the analysis of frozen coarse-grained materials in geotechnical engineering.

scholarly journals Mechanical Properties of Grouted Crushed Coal with Different Grain Size Mixtures under Triaxial Compression

2018 ◽  
Vol 2018 ◽  
pp. 1-13 ◽  
Author(s):  
Yuhao Jin ◽  
Lijun Han ◽  
Qingbin Meng ◽  
Suresh Sanda ◽  
Haizhi Zang ◽  
...  
Keyword(s):  
Grain Size ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Peak Strain ◽  
Compression Tests ◽  
Reinforcement Effect ◽  
Confining Pressures ◽  
Mechanical Behaviours ◽  
Ultimate Failure ◽  
Different Grain Size

To have a better understanding of the reinforcement effect on the crushed zone after grouting in coal mining extraction work, a self-designed grouting apparatus was used to study the effects of the grain size mixtures (distribution) and the stress state on the mechanical behaviours of grouted crushed coal specimens. From the various grouting tests, triaxial compression tests and scanning electron microscopy (SEM) observations of grouted specimens with different grain size mixtures, it was found that, for the same grain size mixture, the peak (σp) and residual (σr) strengths of the grouted specimens increased with an increase in confining pressure. It was found that the average slope values of the σp-σ3 curves for the grouted specimens with different grain size mixtures were all larger than those of the σr-σ3 curves. It was observed that the peak strain (εp) of the grouted specimens with different grain size mixtures increased overall with increasing confining pressure. For constant confining pressure, the peak and residual strengths both gradually increased approximately linearly as the grain size mixtures varied from small to large, but at higher confining pressures, the influence of the grain size mixture on the peak (or residual) strength increased. These mechanical behaviours of the grouted crushed coal specimens were strongly dependent on the variation in the grain size mixtures and in the confining pressure, which can be explained by the crack evolution process within the grouted specimen under triaxial compression, to a certain extent. Ultimate failure of the grouted specimen occurred just after propagation and coalescence of the cracks through the entire grouted specimen. Moreover, there were three major microscopic diffusion modes for the grouts flowing in most of the crushed coal specimens. Based on these test results, it was found that the reinforcement effect of the grouted specimen related to the splitting grouting mode (occurring in most of the large specimens) seems to be better than that of the penetrating (filling) grouting mode (in most of the small specimens).

scholarly journals Strain-Softening Characteristics of Hydrate-Bearing Sediments and Modified Duncan–Chang Model

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Mengqiu Yan ◽  
Rongtao Yan ◽  
Haihao Yu
Keyword(s):  
Strain Softening ◽  
Triaxial Compression ◽  
Compression Tests ◽  
Empirical Formulas ◽  
Softening Behavior ◽  
Initial Modulus ◽  
Hydrate Saturation ◽  
Hydrate Bearing Sediments ◽  
Triaxial Compression Tests ◽  
Chang Model

Marine hydrate exploitation may trigger the seabed geological disaster, such as seafloor collapse and landslide. It is critically important to understand the mechanical properties of hydrate-bearing sediment. Strain-softening observation is a typical behavior of hydrate-bearing sediment (HBS) and exhibits more significant at higher hydrate saturation. This paper performed a series of triaxial compression tests on methane hydrate-bearing sand to analyze the influence rule and mechanism of hydrate saturation on the strain-softening characteristic, stiffness, and strength and introduced the strain-softening index to quantificationally characterize the strain-softening behaviors of HBS with different hydrate saturations. Based on the analyses on the mechanical behavior of HBS, the Duncan–Chang model is extended to address the stress-strain curves of HBS. Two empirical formulas with hydrate saturation embedded are used to characterize the enhanced initial modulus and strength for HBS, respectively. To address the strain-softening behavior of HBS, the modified Duncan–Chang model introduced a damage factor into the strength of HBS. To validate the modified Duncan–Chang model, four different triaxial compression tests are simulated. The good consistence between simulated result and experimental data demonstrates that the modified Duncan–Chang model is capable of reflecting the influence of hydrate saturation not only on the stiffness and strength but also on the strain-softening characteristics of HBS.

scholarly journals Study on Mechanical Properties of the Basalt Fiber-Rubber Granular Concrete under Triaxial Stress Condition and Its Application

2020 ◽  
Vol 10 (23) ◽  
pp. 8540
Author(s):  
Duohua Wu ◽  
Zhiwen Li ◽  
Juli Li ◽  
Bo Peng ◽  
Hui Shen
Keyword(s):  
Mechanical Properties ◽  
Strain Softening ◽  
Yield Criterion ◽  
Triaxial Compression ◽  
High Stress ◽  
Basalt Fiber ◽  
Peak Strain ◽  
Compression Tests ◽  
Basalt Fibers ◽  
Supporting Structures

To reduce the failure probability of rigid supporting structures caused by large deformation of deeply buried high-stress soft rock roadways, the mechanical properties and failure features of basalt fiber-rubber granular concrete (BFRGC) are investigated based on triaxial compression tests. The post-peak strain softening equations of BFRGC, based on the Mohr–Coulomb yield criterion, are deduced and then compiled in the finite-difference software (FLAC3D) to simulate the post-peak strain-softening process of BFRGC. Combined with practical engineering, the supporting effects of BFRGC with different proportions are evaluated by FLAC3D. The results of compression tests show that the yield strength of the BFRGC increases significantly when the mass percentage of basalt fiber is 0.4%. Moreover, mixing basalt fibers into both the plain concrete and rubber concrete can effectively restrain the development of the fractures under three-dimensional stress. The numerical results show that when the mass fractions of basalt fibers and rubber particles are 0.4% and 5–10%, respectively, both the plastic zone in the surrounding rocks and the deformation of the rigid supporting structures decrease obviously. It is indicated that the optimal ratio of BFRGC can effectively reduce the stress concentration around the roadway and improve the overall bearing capacity of the supporting structures.

scholarly journals Experimental Study on Failure Mechanical Properties of Two Kinds of Seafloor Massive Sulfides

Minerals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1144
Author(s):  
Huan Dai ◽  
Yan Li ◽  
Mengdan Li
Keyword(s):  
Mechanical Properties ◽  
Strain Softening ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Small Scale ◽  
Peak Strain ◽  
Massive Sulfides ◽  
Splitting Test ◽  
Two Samples ◽  
Significant Difference

Remarkable hydrostatic pressures have a significant effect on the failure mechanical properties of seafloor minerals, which also affects the selection and development of mining excavation tools. In this paper, a Brazilian splitting test and triaxial compression test were adopted to investigate the strength and deformation behavior of two kinds of seafloor massive sulfides (SMS) samples at a small-scale size. Based on the mineralogical characterization of the studied samples, the mechanical properties were preliminarily correlated with their internal structures and mineral compositions. Results indicate that there is a significant difference in the triaxial compression deformation properties between the two kinds of SMS samples and the geotechnical data are controlled by mineral type and composition, including porosity. In general, the triaxial compression process of the two kinds of samples included initial compaction, elastic stage, yield stage, failure stage and residual stage, and shows strain softening characteristics after the peak. With the increase in confining pressure, the strain-softening behavior of the white sample is mitigated and gradually changes into strain-hardening. The peak strength and peak strain of the two samples increased linearly with the increase in confining pressure within the confining pressure range of these tests, and the failure pattern of the specimens also changed from a typical brittle failure to a ductile failure. The results of this study provide data to support further understanding of different kinds of SMS, and are of great significance in the design of efficient SMS exploitation equipment.

scholarly journals Researches on the Constitutive Models of Artificial Frozen Silt in Underground Engineering

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Yugui Yang ◽  
Feng Gao ◽  
Hongmei Cheng ◽  
Yuanming Lai ◽  
Xiangxiang Zhang
Keyword(s):  
Mechanical Characteristic ◽  
Stress Level ◽  
Strain Softening ◽  
Triaxial Compression ◽  
High Stress ◽  
Constitutive Models ◽  
Confining Pressure ◽  
Frozen Soil ◽  
Conventional Triaxial Compression ◽  
Shear Process

The researches on the mechanical characteristic and constitutive models of frozen soil have important meanings in structural design of deep frozen soil wall. In the present study, the triaxial compression and creep tests have been carried out, and the mechanical characteristic of frozen silt is obtained. The experiment results show that the deformation characteristic of frozen silt is related to confining pressure under conventional triaxial compression condition. The frozen silt presents strain softening in shear process; with increase of confining pressure, the strain softening characteristic gradually decreases. The creep curves of frozen silt present the decaying and the stable creep stages under low stress level; however, under high stress level, once the strain increases to a critical value, the creep strain velocity gradually increases and the specimen quickly happens to destroy. To reproduce the deformation behavior, the disturbed state elastoplastic and new creep constitutive models of frozen silt are developed. The comparisons between experimental results and calculated results from constitutive models show that the proposed constitutive models could describe the conventional triaxial compression and creep deformation behaviors of frozen silt.

scholarly journals Triaxial Testing of Geosynthetics Reinforced Tailings with Different Reinforced Layers

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1943
Author(s):  
Fu Yi ◽  
Changbo Du
Keyword(s):  
Triaxial Compression ◽  
Friction Angle ◽  
Confining Pressure ◽  
Test Results ◽  
Compression Tests ◽  
Strength Index ◽  
Stress Strain ◽  
High Confining Pressure ◽  
Zhang Model ◽  
Triaxial Compression Tests

To evaluate the shear properties of geotextile-reinforced tailings, triaxial compression tests were performed on geogrids and geotextiles with zero, one, two, and four reinforced layers. The stress–strain characteristics and reinforcement effects of the reinforced tailings with different layers were analyzed. According to the test results, the geogrid stress–strain curves show hardening characteristics, whereas the geotextile stress–strain curves have strain-softening properties. With more reinforced layers, the hardening or softening characteristics become more prominent. We demonstrate that the stress–strain curves of geogrids and geotextile reinforced tailings under different reinforced layers can be fitted by the Duncan–Zhang model, which indicates that the pseudo-cohesion of shear strength index increases linearly whereas the friction angle remains primarily unchanged with the increase in reinforced layers. In addition, we observed that, although the strength of the reinforced tailings increases substantially, the reinforcement effect is more significant at a low confining pressure than at a high confining pressure. On the contrary, the triaxial specimen strength decreases with the increase in the number of reinforced layers. Our findings can provide valuable input toward the design and application of reinforced engineering.

scholarly journals Experimental Investigation and Micromechanical Modeling of Elastoplastic Damage Behavior of Sandstone

Materials ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3414
Author(s):  
Chaojun Jia ◽  
Qiang Zhang ◽  
Susheng Wang
Keyword(s):  
Damage Evolution ◽  
Triaxial Compression ◽  
Damage Model ◽  
Confining Pressure ◽  
Micromechanical Modeling ◽  
Compression Tests ◽  
Integration Algorithm ◽  
Damage Behavior ◽  
Plastic Strain Increment ◽  
Elastoplastic Damage

The mechanical behavior of the sandstone at the dam site is important to the stability of the hydropower station to be built in Southwest China. A series of triaxial compression tests under different confining pressures were conducted in the laboratory. The critical stresses were determined and the relationship between the critical stress and confining pressure were analyzed. The Young’s modulus increases non-linearly with the confining pressure while the plastic strain increment Nϕ and the dilation angle ϕ showed a negative response. Scanning electron microscope (SEM) tests showed that the failure of the sandstone under compression is a coupled process of crack growth and frictional sliding. Based on the experimental results, a coupled elastoplastic damage model was proposed within the irreversible thermodynamic framework. The plastic deformation and damage evolution were described by using the micromechanical homogenization method. The plastic flow is inherently driven by the damage evolution. Furthermore, a numerical integration algorithm was developed to simulate the coupled elastoplastic damage behavior of sandstone. The main inelastic properties of the sandstone were well captured. The model will be implemented into the finite element method (FEM) to estimate the excavation damaged zones (EDZs) which can provide a reference for the design and construction of such a huge hydropower project.

scholarly journals Microcracking and the failure of polycrystalline ice under triaxial compression

1992 ◽  
Vol 38 (128) ◽  
pp. 65-76 ◽  
Author(s):  
P. Kalifa ◽  
G. Ouillon ◽  
P. Duval
Keyword(s):  
Triaxial Compression ◽  
Peak Stress ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Strain History ◽  
Compression Tests ◽  
Brittle Transition ◽  
Polycrystalline Ice ◽  
Strain Components

AbstractTriaxial and uniaxial compression tests have been carried out at –10°C on granular ice in order to study the role of microcracking on failure in the ductile-brittle transition zone. In the triaxial tests, the effect of confining pressure and strain rate on the crack population, as well as on strength and strain at the peak stress, was investigated. In the uniaxial tests, we measured the evolution of elastic and non-elastic components of deformation with the stress-strain history. The concept of effective stress, with a single scalar damage variable, was used to calculate the effect of microcracking on the strain components.

Mechanical Properties of Bentonite-Sand Mixtures Under Triaxial Stress Condition

1994 ◽  
Vol 353 ◽  
Author(s):  
M. Umedera ◽  
A. Fujiwara ◽  
N. Yasufuku ◽  
M. Hyodo ◽  
H. Murata
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Water Content ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Strength Properties ◽  
Compression Tests ◽  
Optimum Water Content ◽  
Triaxial Compression Tests ◽  
Optimum Water

AbstractA series of triaxial compression tests is being conducted under the drained condition on bentonite and sand mixtures, known as buffer, in saturated and optimum water content states to clarify the mechanical properties of the buffer.It was found that the mechanical properties of bentonite and sand mixtures are strongly influenced by water and bentonite contents: shear strength in a saturated state is less than that in an optimum water content state; shear strength decreases rapidly with increasing bentonite content. Strength properties are much dependent on confining pressure.

Sign in / Sign up

Export Citation Format

Share Document