scholarly journals Field Test Research on Red Clay Slope under Atmospheric Action

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Kaisheng Chen
Keyword(s):  
Internal Friction ◽  
Water Content ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Friction Angle ◽  
Internal Friction Angle ◽  
Red Clay ◽  
Failure Characteristics ◽  
Clay Slopes

By embedding water content sensors and pore water pressure sensors inside the red clay slope on-site in Guiyang, Guizhou, shear tests were performed on soil samples at different depths of the slope under different weather. The changes of water content, pore water pressure, and shear strength index of the slope inside the slope under the influence of the atmosphere were tracked and tested, and the failure characteristics and evolution of the red clay slope were analyzed. It is believed that the depth of influence of the atmosphere on red clay slopes is about 0.7 m, rainfall is the most direct climatic factor leading to the instability of red clay slopes, and the evaporation effect is an important prerequisite for the catastrophe of red clay slopes. The cohesion and internal friction angle of the slope soil have a good binary quadratic function relationship with the water content and density. The water content and density can be used to calculate the cohesion and internal friction angle. Failure characteristics of red clay slopes: the overall instability failure is less, mainly surface failure represented by gullies and weathering and spalling, and then gradually evolved into shallow instability failure represented by collapse and slump. The damage evolution law is as follows: splash corrosion and surface corrosion stage⟶ fracture development stage⟶ gully formation stage⟶ gully development through stage⟶ local collapse stage⟶ slope foot collapse stage.

Back-analysis of geophysical flows using three-dimensional runout model

2018 ◽  
Vol 55 (8) ◽  
pp. 1081-1094 ◽  
Author(s):  
R.C.H. Koo ◽  
J.S.H. Kwan ◽  
C. Lam ◽  
G.R. Goodwin ◽  
C.E. Choi ◽  
...  
Keyword(s):  
Finite Element ◽  
Internal Friction ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Three Dimensional ◽  
Friction Angle ◽  
Geophysical Flows ◽  
Internal Friction Angle ◽  
Case Histories

Predicting the mobility and delineating the extent of geophysical flows remains a challenge for engineers. The accuracy of predictions hinges on the reliability of input parameters of runout models. Currently, limited field data for landslide case histories are available for benchmarking the performance of runout models. Key rheological parameters, such as the equivalent internal friction angle, cannot be measured directly using laboratory experiments and must instead be determined through back-analyses. A series of dynamic back-analyses was carried out for notable landslide case histories in Hong Kong, accounting for the effects of pore-water pressure on the equivalent internal friction angle, using a three-dimensional finite-element mobility model. The recorded and simulated run-out distances, as well as lateral spreading, were compared. Results reveal that the back-analysed equivalent internal friction angles resulting from open-hillslope failures and from channelized geophysical flows range from 25° to 30° and 15° to 20°, respectively. This is attributed to incised geophysical flow channels having an elevated water head and higher degree of saturation compared to open-hillside slope surfaces, wherein the induced elevated pore-water pressure profoundly lowers the equivalent internal friction angle. The back-calculated values may be useful for finite-element-based design of mitigation measures.

scholarly journals Evaluation of Sand-Shell Mixture Behaviour for Breakwater Foundation

2016 ◽  
Author(s):  
Abbass Tavallali ◽  
Justine Mollaert
Keyword(s):  
Internal Friction ◽  
Relative Density ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Friction Angle ◽  
Internal Friction Angle ◽  
Triaxial Tests ◽  
Direct Shear Tests ◽  
Different Depths ◽  
Sand Material

The available sand material for a breakwater foundation is mixed with shells. The shell percentage of the sand material is variable and percentages up to even 50% are observed. It is essential to evaluate the properties and the behaviour of the sand-shell mixture as this will form the improved breakwater foundation. In reality the backfilled sand of the breakwater foundation has different relative densities in different depths. In this study the mechanical properties of the sand-shell mixture for different relative densities are evaluated. For different relative densities of sand-shell mixture the direct shear tests and the consolidated undrained triaxial tests are carried out on some samples. The results of the experiments showed that the samples with higher relative density show a higher internal friction angle. However, for the samples with even low relative density, an internal friction angle of less than 32° is not observed. The volume variation of the samples with different relative densities are monitored. Samples with low relative density showed a contraction behaviour; resulting in an increase of the pore water pressure, a reduction of the effective strength and finally the samples become susceptible to liquefaction. While the samples with high relative density showed a dilatancy behaviour.

scholarly journals Experimental study on the mechanical properties of Guiyang red clay considering the meso micro damage mechanism and stress path

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Yanzhao Zhang ◽  
Shuangying Zuo ◽  
Rita Yi Man Li ◽  
Yunchuan Mo ◽  
Guosheng Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Soil Sample ◽  
Pore Water ◽  
Shear Failure ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Strain Curve ◽  
Friction Angle ◽  
Red Clay ◽  
Stress Strain

Abstract This study investigated the macroscopic physical and mechanical properties of Guiyang red clay during surcharge loading, lateral excavation and lateral unloading with axial loading, and clarified the failure mechanism of microstructure before and after shear under different stress paths of CTC, RTC and TC. Consolidated undrained triaxial shear permeability, SEM scanning, XRF fluorescence spectrum analysis and XRD diffraction tests were conducted to simulate the actual engineering conditions. The stress–strain curve, shear strength, pore water pressure variation rule and macroscopic failure mode of soil samples under different stress paths were analysed. In addition, Image Pro Plus 6.0 and PCAS were used to study the relationship between the macro mechanical properties and micro microstructure failure under different stress paths. The stress–strain curves from CTC, RTC and TC in CU tests were different, with the peak values of shear stress under the three stress paths being P-increasing, equal P-path and P-decreasing path. Moreover, the internal friction angle and cohesion of the increasing P path were higher than those of equal P path and decreasing P path, hence, the influence of stress paths on the cohesion is greater than that of internal friction angle. The pore water pressure is strongly dependent on the stress path, and the variation characteristics of pore water pressure are consistent with the change in the law of the stress–strain curve. Under the same confining pressure in the P-increasing path, the shear failure zone runs through the whole soil sample, and the shear failure zone is significant, whereas under the condition of the P-reducing path, the shear failure angle of soil sample is about 65°, 55° and 45°, and in the equal P path, the soil sample is dominated by the confining pressure, with no obvious microcrack on the surface of the soil sample. The difference is that the distribution of pores in the path of increasing P and equal P is directional, and the anisotropy rate is small, while the distribution of pores in soil samples with shear failure and before shear is random and the anisotropy rate is high.

Characterization of Shear Strength and Interface Friction of Organic Soil

2020 ◽  
Vol 857 ◽  
pp. 203-211
Author(s):  
Majid Hamed ◽  
Waleed S. Sidik ◽  
Hanifi Canakci ◽  
Fatih Celik ◽  
Romel N. Georgees
Keyword(s):  
Shear Stress ◽  
Shear Strength ◽  
Internal Friction ◽  
Moisture Content ◽  
Water Content ◽  
Friction Angle ◽  
Structural Materials ◽  
Organic Soil ◽  
Internal Friction Angle ◽  
Interface Friction

This study was undertaken to investigate some specific problems that limit a safe design and construction of structures on problematic soils. An experimental study was carried out to examine the influence of loading rate and moisture content on shear strength of organic soil. Influece of moisture content on interface friction between organic soil and structural materials was also attempted. A commonly used soil in Iraq was prepared at varying moisture contents of 39%, 57% and 75%. The experimental results showed that the increase in water content will decrease the shear stress and the internal friction angle. An increase of the shearing rate was found to decrease the shear stress and internal friction angle for all percetanges of water contents. Further, direct shear tests were carried out to detect the interface shear stress behavior between organic soil and structural materials. The results revealed that the increase in water content was shown to have significant negetavie effects on the interface internal friction and angle shear strength.

Aspects of the behaviour of compacted clayey soils on drying and wetting paths

2002 ◽  
Vol 39 (6) ◽  
pp. 1341-1357 ◽  
Author(s):  
Jean-Marie Fleureau ◽  
Jean-Claude Verbrugge ◽  
Pedro J Huergo ◽  
António Gomes Correia ◽  
Siba Kheirbek-Saoud
Keyword(s):  
Water Content ◽  
Pore Water ◽  
Unsaturated Soils ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Dry Density ◽  
Clayey Soils ◽  
Maximum Dry Density ◽  
Optimum Water Content ◽  
Optimum Water

A relatively large number of drying and wetting tests have been performed on clayey soils compacted at the standard or modified Proctor optimum water content and maximum density and compared with tests on normally consolidated or overconsolidated soils. The results show that drying and wetting paths on compacted soils are fairly linear and reversible in the void ratio or water content versus negative pore-water pressure planes. On the wet side of the optimum, the wetting paths are independent of the compaction water content and can be approached by compaction tests with measurement of the negative pore-water pressure. Correlations have been established between the liquid limit of the soils and such properties as the optimum water content and negative pore-water pressure, the maximum dry density, and the swelling or drying index. Although based on a limited number of tests, these correlations provide a fairly good basis to model the drying–wetting paths when all the necessary data are not available.Key words: compaction, unsaturated soils, clays, drying, wetting, Proctor conditions.

Experimental verification of the theory of consolidation for unsaturated soils

1995 ◽  
Vol 32 (5) ◽  
pp. 749-766 ◽  
Author(s):  
Harianto Rahardjo ◽  
Delwyn G. Fredlund
Keyword(s):  
Water Content ◽  
Pore Pressure ◽  
Pore Water ◽  
Unsaturated Soils ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Matric Suction ◽  
Water Volume ◽  
Loading Tests ◽  
Undrained Loading

An experimental program was designed to study the behavior of unsaturated soils during undrained loading and consolidation. A Ko cylinder was designed and built for the testing program. Simultaneous measurements of pore-air and pore-water pressures could be made throughout a soil specimen using this Ko cylinder. Four types of tests were performed on a silty sand. These are (1) undrained loading tests where both the air and water are not allowed to drain, (2) constant water content tests where only the water phase is not allowed to drain, (3) consolidation tests where both the air and water phases are allowed to drain, and (4) increasing matric suction tests. Undrained loading tests or constant water content loading tests were conducted for measuring the pore pressure parameters for the unsaturated soil. Drained tests consisting of either consolidation tests or increasing matric suction tests were conducted to study the pore pressure distribution and volume change behavior throughout an unsaturated soil during a transient process. The experimental pore pressure parameters obtained from the undrained loadings and constant water content leadings agreed reasonably well with theory. The pore-air pressure was found to dissipate instantaneously when the air phase is continuous. The pore-water pressure dissipation during the consolidation test was found to be faster than the pore-water pressure decrease during the increasing matric suction test. The differing rates of dissipation were attributed to the different coefficients of water volume change for each of the tests. The water volume changes during the consolidation test were considerably smaller than the water volume changes during the increasing matric suction tests for the same increment of pressure change. Key words : consolidation, Ko loading, matric suction, pore-air pressures, pore-water pressures, unsaturated soils

scholarly journals Laboratory Experiment and Numerical Analysis on the Precursory Hydraulic Process of Rainfall-Induced Slope Failure

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Joon-Young Park ◽  
Young-Suk Song
Keyword(s):  
Numerical Modeling ◽  
Laboratory Test ◽  
Water Content ◽  
Pore Water ◽  
Slope Failure ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Volumetric Water Content ◽  
Wetting Front ◽  
Artificial Rainfall

A combined analysis involving a laboratory test and numerical modeling was performed to investigate the hydraulic processes leading to slope failure during rainfall. Through a laboratory landslide test in which artificial rainfall was applied to a homogeneous sandy slope, the timing and configurations of multiple slides were identified. In addition, volumetric water content was measured in real time through the use of monitoring sensors. The measured volumetric water content data were then used to validate the relevance of the numerical modeling results. The validated numerical modeling of the laboratory-scale slope failures provided insight into the hydraulic conditions that trigger landslides. According to the numerical modeling results, the miniaturized slope in the laboratory test was saturated in a manner so that the wetting front initially progresses downward and then the accumulated rainwater at the toe of the slope creates a water table that advances toward the crest. Furthermore, each of the five sequential failures that occurred during this experiment created slip surfaces where the pore-water pressure had achieved full saturation and an excessive pore-water pressure state. The findings of this study are expected to help understand the hydraulic prerequisites of landslide phenomena.

Study on the Effect of Water Content on Shearing Strength Parameters of Unsaturated Loess

2014 ◽  
Vol 638-640 ◽  
pp. 585-588 ◽  
Author(s):  
Si Zhong Qian
Keyword(s):  
Internal Friction ◽  
Water Content ◽  
Friction Angle ◽  
Internal Friction Angle ◽  
Direct Shear ◽  
Strength Parameters ◽  
Direct Shear Tests ◽  
Micro Particles ◽  
Shearing Strength ◽  
Unsaturated Loess

This paper experiments on typical Malan loess, performs consolidated quick direct shear tests under different water contents by conventional direct shear apparatus, then analyzes the effects of water content on shearing strength parameters, namely cohesion and internal friction angle. The results show that cohesion decreases linearly as the water content increasing, and the relation could be obtained by data fitting. However, internal friction angle keeps basically stable with the increase of water content. Finally, based on the force analysis for micro particles, the changing rules of cohesion and internal friction angle with water content were deeply explained.

scholarly journals Discussion on the Characteristics of Seismic Signals Due to Riverbank Landslides from Laboratory Tests

Water ◽  
2019 ◽  
Vol 12 (1) ◽  
pp. 83
Author(s):  
Zheng-Yi Feng ◽  
Chia-Ming Hsu ◽  
Shi-Hao Chen
Keyword(s):  
Water Content ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Water Levels ◽  
Seismic Signals ◽  
Transform Method ◽  
Frequency Distributions ◽  
Landslide Event ◽  
Self Potential

Floods and erosion often cause landslides of riverbanks and induce problems such as river blockage, shift of river center, or flooding from rising riverbeds. Instrumentation and monitoring are often used to explore landslide and erosion behavior of riverbanks. Therefore, this study identified landslide types and characteristics of their seismic signals due to toe erosion of riverbanks through riverbank models with various instrumentation sensors in a laboratory flume. To induce landslides in the riverbank model, a test was set up for water to flow through the toe of the riverbank model. Seismic signals of each landslide event were measured during the tests with accelerometers. Nonpolarized electrodes were installed for observing the self-potential changes during the test. Water content and pore water pressure gauges were installed in the riverbank model. In addition, water levels were recorded. The Hilbert–Huang transform method was used to analyze the characteristics of seismic signals caused by water flow and riverbank landslides. Time points, landslide frequency distributions, and the characteristics of several landslide events in the riverbank models were estimated using the seismic signals. This study identified three types of landslides: single, intermittent, and successive. Moreover, changes in self-potential signals, pore water pressure, and water content during the tests were examined and were found to correspond to the landslide process of the riverbank model.

Sign in / Sign up

Export Citation Format

Share Document