scholarly journals Model Tests on Y-Shaped Piles under Compressive and Lateral Loading in Saturated Sand

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Lian-wei Ren ◽  
Quan-wei Yang ◽  
Gang-qiang Kong ◽  
Zhi-lin Dun ◽  
Xin-yu Wang
Keyword(s):  
Bearing Capacity ◽  
Ground Improvement ◽  
Coastal Region ◽  
Bending Moment ◽  
Model Tests ◽  
Saturated Sand ◽  
Soil Pressure ◽  
Cross Sectional ◽  
Side Resistance ◽  
New Type

Y-shaped piles are a new type of pile whose cross-section is like the letter Y: they are often used in ground improvement for road or train subgrades in the eastern coastal region of China. To investigate the bearing behaviour of Y-shaped piles in saturated sand, a series of model tests under compressive and horizontal load for Y-shaped piles, C 1 circular pile (the same cross-sectional area of Y-shaped pile), and C 2 circular pile (the same perimeter of Y-shaped pile) were carried out. Comparative analysis was conducted on bearing capacity, axial force and side resistance distribution, load sharing ratio, bending moment, and lateral soil pressure distribution along the embedded length. The results show that the bearing capacity of a Y-shaped pile does not increase in proportion, and the shaft resistance is weakened to some extent in saturated sand; Y-shaped pile can effectively improve the compressive bearing capacity for the same amount of concrete. The lateral bearing capacity of a Y-shaped pile has directionality, and hanging a circular section into a Y-shaped section may improve the horizontal bearing capacity for the same amount concrete, but cannot give full play to the advantage of the larger side area for horizontal bearing capacity in saturated sand.

scholarly journals An Experimental Study of Horizontal Bearing Capacity of Vertical Steel Floral Tube Micropiles with Double Grouting

2018 ◽  
Vol 2018 ◽  
pp. 1-11
Author(s):  
Kaiyang Wang ◽  
Yanjun Shang
Keyword(s):  
Bearing Capacity ◽  
Large Scale ◽  
Slip Surface ◽  
Bending Moment ◽  
Shear Capacity ◽  
Soil Reinforcement ◽  
Scale Model ◽  
Soil Pressure ◽  
Floral Tube ◽  
Grouting Pressure

This paper examines the performance of a novel technology, vertical steel floral tube micropiles with double grouting. It is the combination of micropile technology and double grouting technology. A large-scale model tank was applied to impart horizontal bearing capacity, and the slope soil pressure and flexural performance of the micropile were investigated under four experimental conditions. The peak grouting pressure during the double grouting process was defined as the fracturing pressure of the double grouting, and it was positively correlated to the interval time between first grouting and secondary grouting. Compared with traditional grouting, double grouting increased the horizontal bearing capacity of the single micropile with the vertical steel floral tube by 24.42%. The horizontal bearing capacity was also 20.25% higher for the structure with three micropiles, compared with a 3-fold value of horizontal sliding resistance. In the test, the maximum bending moment acting on the pile above the sliding surface was located 2.0–2.5 m away from the pile top, and the largest negative bending moment acting on the pile below the slip surface was located 4.0 m away from the pile top. The ultimate bending moment of the single pile increased by 12.8 kN·m with double grouting, and the bending resistance increased by 96.2%. The experimental results showed that the double grouting technology significantly improved the horizontal bearing capacity of the micropile with the steel floral tube, and the soil reinforcement performance between piles was more pronounced. Also, the shear capacity and the flexural capacity were significantly improved compared with the original technology.

Model Test Study on the Effect of Horizontal Load on the Vertical Bearing Capacity of Disk Pile

2011 ◽  
Vol 368-373 ◽  
pp. 2571-2574
Author(s):  
Cheng Yuan Lu ◽  
Jin Jin Li ◽  
Fan Li Meng
Keyword(s):  
Bearing Capacity ◽  
Bending Moment ◽  
Horizontal Displacement ◽  
Initial Time ◽  
Horizontal Load ◽  
Vertical Load ◽  
Soil Pressure ◽  
Test Study ◽  
Vertical Bearing ◽  
Vertical Bearing Capacity

A group of model tests were designed to study the effect of horizontal load on the vertical bearing capacity of disk pile. Three double-disk piles were used in the test, and the distance of the two disks is 5 times as the disk diameter. Drew a horizontal load H=100N/200N/300N on the top of pile1/2/3 respectively, and put on the vertical load stage by stage, then studied the differences of three piles’ bearing properties such as changes of the pile bending moment, the horizontal and vertical deformation on the top, and soil pressure around the pile. Experiment showed that when the horizontal load is quite small, the existence of horizontal load has little to do with vertical bearing capacity. When the load reached a certain level, the p-∆ effect under the vertical load will significantly affect the vertical bearing capacity of the pile. Especially during the initial time while there is a large horizontal displacement or rotation generated by the horizontal load, the pile’s bearing capacity is controlled by the horizontal displacement.

Experimental Study on Bearing Behavior of Large-Diameter Overlength Squeezed Branch Pile

2011 ◽  
Vol 243-249 ◽  
pp. 3244-3250
Author(s):  
Jin Lu Jia ◽  
Zhong Fu Wang ◽  
Jian Hua Zheng
Keyword(s):  
Bearing Capacity ◽  
Large Diameter ◽  
Load Ratio ◽  
The Body ◽  
Static Test ◽  
Force Transfer ◽  
Side Resistance ◽  
New Type ◽  
S Curve ◽  
Vertical Bearing

Squeezed branch pile is based on the traditional uniform pile in development of a new type of pile, with a high bearing capacity, settlement of small features widely used in the engineering. Based on the actual project site static test, analyzed the vertical bearing capacity characteristics of two adjacent squeezed branch piles; By means of testing of the pile stress gauge steel embedded in different parts of piles, the axial force transfer characteristics of the body, support plate side resistance drag and play characteristics of the squeezed branch pile were analyzed. The results showed that: the branch pile Q-S curve is slowly varying type, the three branch share of the load ratio increases with the pile top load increases and then decreases, load sharing ratio of 12% or so. The side resistance increased with the pile top displacement, the curve showed significant enhancement traits. Measured friction value of two test piles is too conservative under the existing norms, the actual measured value of 1.2～1.6 times of the standardized value.

scholarly journals INTERACTION DIAGRAMS AXIAL FORCE-BENDING MOMENT FOR FIRE EXPOSED STEEL-CONCRETE COMPOSITE SECTIONS

2016 ◽  
Author(s):  
Milivoje Milanovic ◽  
Meri Cvetkovska
Keyword(s):  
Bearing Capacity ◽  
Cross Section ◽  
Axial Force ◽  
Bending Moment ◽  
Cross Sectional ◽  
Load Bearing ◽  
Composite Columns ◽  
Interaction Diagram ◽  
Steel Sections ◽  
The Cross

The bearing capacity of the column cross section can be determined from the interaction diagram moment-axial force (M–N). Fire induced temperatures cause reduction of the load-bearing characteristics of the constitutive materials, steel and concrete, and this effect directly reflects on the reduction of the axial force and the bending moment that could be accepted by the column cross section, respectively the interaction diagram of the column cross section is changed. The load bearing capacity of the steel-concrete composite columns exposed to fire from all four sides and loaded by axial force and uni-axial or bi-axial bending moments, was estimated on the basis of the changes in the interaction diagrams moment-axial force amd the results are presented in this paper. Different types of composite columns made of totally or partially encased steel sections, or concrete filled hollow sections were analyzed and a detailed discussion on the effects of the shape of the cross section and the cross sectional dimensions are presented.

Load-Bearing Capacity of Direct Inlay-Retained Fibre-reinforced Composite Fixed Partial Dentures with Different Cross-Sectional Pontic Design

2017 ◽  
Vol 68 (1) ◽  
pp. 94-100
Author(s):  
Oana Tanculescu ◽  
Adrian Doloca ◽  
Raluca Maria Vieriu ◽  
Florentina Mocanu ◽  
Gabriela Ifteni ◽  
...  
Keyword(s):  
Bearing Capacity ◽  
Fracture Pattern ◽  
Load Bearing Capacity ◽  
Cross Sectional ◽  
Load Bearing ◽  
Reinforced Composite ◽  
Polyethylene Fibre

The load-bearing capacity and fracture pattern of direct inlay-retained FRC FDPs with two different cross-sectional designs of the ponticwere tested. The aim of the study was to evaluate a new fibre disposition. Two types of composites, Filtek Bulk Fill Posterior Restorative and Filtek Z250 (3M/ESPE, St. Paul, MN, USA), and one braided polyethylene fibre, Construct (Kerr, USA) were used. The results of the study suggested that the new tested disposition of the fibres prevented in some extend the delamination of the composite on buccal and facial sides of the pontic and increased the load-bearing capacity of the bridges.

scholarly journals Behavior Characteristics of Single Batter Pile under Vertical Load

2021 ◽  
Vol 11 (10) ◽  
pp. 4432
Author(s):  
Jiseong Kim ◽  
Seong-Kyu Yun ◽  
Minsu Kang ◽  
Gichun Kang
Keyword(s):  
Bearing Capacity ◽  
Relative Density ◽  
Model Test ◽  
Ground Surface ◽  
Bending Moment ◽  
Vertical Position ◽  
Vertical Load ◽  
Behavior Characteristics

The purpose of this study is to grasp the behavior characteristics of a single batter pile under vertical load by performing a model test. The changes in the resistance of the pile, the bending moment, etc. by the slope of the pile and the relative density of the ground were analyzed. According to the results of the test, when the relative density of the ground was medium and high, the bearing capacity kept increasing when the angle of the pile moved from a vertical position to 20°, and then decreased gradually after 20°. The bending moment of the pile increased as the relative density of the ground and the batter angle of the pile increased. The position of the maximum bending moment came closer to the ground surface as the batter angle of the pile further increased, and it occurred at a point of 5.2~6.7 times the diameter of the pile from the ground surface.

scholarly journals Near-Fault Seismic Response Analysis of Bridges Considering Girder Impact and Pier Size

Mathematics ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 704
Author(s):  
Wenjun An ◽  
Guquan Song ◽  
Shutong Chen
Keyword(s):  
Seismic Response ◽  
Bending Moment ◽  
Expansion Method ◽  
Response Analysis ◽  
Seismic Action ◽  
Transient Wave ◽  
Cross Sectional ◽  
Displacement Response ◽  
Near Fault ◽  
Continuous Girder Bridge

Given the influence of near-fault vertical seismic action, we established a girder-spring-damping-rod model of a double-span continuous girder bridge and used the transient wave function expansion method and indirect modal function method to calculate the seismic response of the bridge. We deduced the theoretical solution for the vertical and longitudinal contact force and displacement response of the bridge structure under the action of the near-fault vertical seismic excitation, and we analyzed the influence of the vertical separation of the bridge on the bending failure of the pier. Our results show that under the action of a near-fault vertical earthquake, pier-girder separation will significantly alter the bridge’s longitudinal displacement response, and that neglecting this separation may lead to the underestimation of the pier’s bending damage. Calculations of the bending moment at the bottom of the pier under different pier heights and cross-sectional diameters showed that the separation of the pier and the girder increases the bending moment at the pier’s base. Therefore, the reasonable design of the pier size and tensile support bearing in near-fault areas may help to reduce longitudinal damage to bridges.

Sign in / Sign up

Export Citation Format

Share Document