scholarly journals On the Quantitative Low-Level Aerosol Measurements Using Ceilometer-Type Lidar

2009 ◽  
Vol 26 (11) ◽  
pp. 2340-2352 ◽  
Author(s):  
Anu-Maija Sundström ◽  
Timo Nousiainen ◽  
Tuukka Petäjä
Keyword(s):  
Size Distribution ◽  
Theoretical Calculations ◽  
Measurement Instrument ◽  
Aerosol Size Distribution ◽  
Lidar Measurement ◽  
Size Distributions ◽  
Absolute Accuracy ◽  
Particle Composition ◽  
Aerosol Measurement

Abstract The objective of this work is to investigate whether a commercial ceilometer-type lidar can be used as a quantitative aerosol measurement instrument. To this end, lidar backscattering measurements are compared with exact theoretical calculations of backscattering, which are based on in situ–measured size distributions and account for uncertainties in particle composition and shape. The results show that the differences between simulated and measured backscattering remain nearly constant and within the uncertainties involved. The differences are most plausibly explained by an error in the overlap function of the lidar and/or errors in the calibration of either the lidar or the in situ instruments used to measure the aerosol size distribution. Occasionally, large differences occur that are obviously connected to the unrepresentativeness of the in situ and lidar measurement volumes because of insufficient atmospheric mixing. The results imply that the absolute accuracy of the instrument investigated might be sufficient for quantitative aerosol measurements in some applications. A fix for the overlap function, however, would be desirable.

scholarly journals Evaluating model parameterizations of submicron aerosol scattering and absorption with in situ data from ARCTAS 2008

2016 ◽  
Vol 16 (14) ◽  
pp. 9435-9455 ◽  
Author(s):  
Matthew J. Alvarado ◽  
Chantelle R. Lonsdale ◽  
Helen L. Macintyre ◽  
Huisheng Bian ◽  
Mian Chin ◽  
...  
Keyword(s):  
Optical Properties ◽  
Size Distribution ◽  
Aerosol Size Distribution ◽  
Visible Radiation ◽  
Submicron Aerosol ◽  
In Situ Data ◽  
Aerosol Absorption ◽  
Aerosol Scattering ◽  
The Impact

Abstract. Accurate modeling of the scattering and absorption of ultraviolet and visible radiation by aerosols is essential for accurate simulations of atmospheric chemistry and climate. Closure studies using in situ measurements of aerosol scattering and absorption can be used to evaluate and improve models of aerosol optical properties without interference from model errors in aerosol emissions, transport, chemistry, or deposition rates. Here we evaluate the ability of four externally mixed, fixed size distribution parameterizations used in global models to simulate submicron aerosol scattering and absorption at three wavelengths using in situ data gathered during the 2008 Arctic Research of the Composition of the Troposphere from Aircraft and Satellites (ARCTAS) campaign. The four models are the NASA Global Modeling Initiative (GMI) Combo model, GEOS-Chem v9-02, the baseline configuration of a version of GEOS-Chem with online radiative transfer calculations (called GC-RT), and the Optical Properties of Aerosol and Clouds (OPAC v3.1) package. We also use the ARCTAS data to perform the first evaluation of the ability of the Aerosol Simulation Program (ASP v2.1) to simulate submicron aerosol scattering and absorption when in situ data on the aerosol size distribution are used, and examine the impact of different mixing rules for black carbon (BC) on the results. We find that the GMI model tends to overestimate submicron scattering and absorption at shorter wavelengths by 10–23 %, and that GMI has smaller absolute mean biases for submicron absorption than OPAC v3.1, GEOS-Chem v9-02, or GC-RT. However, the changes to the density and refractive index of BC in GC-RT improve the simulation of submicron aerosol absorption at all wavelengths relative to GEOS-Chem v9-02. Adding a variable size distribution, as in ASP v2.1, improves model performance for scattering but not for absorption, likely due to the assumption in ASP v2.1 that BC is present at a constant mass fraction throughout the aerosol size distribution. Using a core-shell mixing rule in ASP overestimates aerosol absorption, especially for the fresh biomass burning aerosol measured in ARCTAS-B, suggesting the need for modeling the time-varying mixing states of aerosols in future versions of ASP.

scholarly journals Methodology for determining rom size distribution

2014 ◽  
Vol 67 (4) ◽  
pp. 405-412
Author(s):  
Christiane Ribeiro da Silva ◽  
Vládia C. G. de Souza ◽  
Jair C. Koppe
Keyword(s):  
Size Distribution ◽  
Distribution Curve ◽  
Size Distributions ◽  
Sampling Protocol ◽  
Product Size ◽  
Operational Conditions ◽  
Specific Protocol ◽  
Open Side ◽  
Ore Dressing

A methodology to determine the size distribution curve of the ROM was developed in a Brazilian iron ore mine. The size of the larger fragments was determined taking photographs and setting the scale of the images to analyze their dimensions (length of their edges and areas). This was implemented according to a specific protocol of sampling that involves split and homogenization stages in situ of a considerable quantity of ore (about 259 metric tonnes). During the sampling process, larger fragments were separated and smaller size material was screened. The methodology was developed initially in order to preview the performance of a primary gyratory crusher that is fed directly from trucks. Operational conditions of the equipment such as closed and open-side settings could be adjusted previously, obtaining different product size distributions. Variability of size of the fragments affects subsequent stages of crushing and can increase circulating load in the circuit. This leads to a decrease of productivity or recovery of the ore dressing. The results showed insignificant errors of accuracy and reproducibility of the sampling protocol when applied to friable itabirite rocks.

scholarly journals Combining airborne in situ and ground-based lidar measurements for attribution of aerosol layers

2018 ◽  
Author(s):  
Anna Nikandrova ◽  
Ksenia Tabakova ◽  
Antti Manninen ◽  
Riikka Väänänen ◽  
Tuukka Petäjä ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Size Distribution ◽  
Aerosol Size Distribution ◽  
Long Range Transport ◽  
Back Trajectories ◽  
Clear Sky ◽  
Temporal And Spatial Variability ◽  
Range Transport ◽  
Temporal And Spatial

Abstract. Understanding the distribution of aerosol layers is important for determining long range transport and aerosol radiative forcing. In this study we combine airborne in situ measurements of aerosol with data obtained by a ground-based High Spectral Resolution Lidar (HSRL) and radiosonde profiles to investigate the temporal and vertical variability of aerosol properties in the lower troposphere. The HSRL was deployed in Hyytiälä, Southern Finland, from January to September 2014 as a part of the US DoE ARM (Atmospheric Radiation Measurement) mobile facility during the BAECC (Biogenic Aerosols – Effects on Cloud and Climate) Campaign. Two flight campaigns took place in April and August 2014 with instruments measuring the aerosol size distribution from 10 nm to 10 µm at altitudes up to 3800 m. Two case studies from the flight campaigns, when several aerosol layers were identified, were selected for further investigation: one clear sky case, and one partly cloudy case. During the clear sky case, turbulent mixing ensured low temporal and spatial variability in the measured aerosol size distribution in the boundary layer whereas mixing was not as homogeneous in the boundary layer during the partly cloudy case. The elevated layers exhibited greater temporal and spatial variability in aerosol size distribution, indicating a lack of mixing. New particle formation was observed in the boundary layer during the clear sky case, and nucleation mode particles were also seen in the elevated layers that were not mixing with the boundary layer. Interpreting local measurements of elevated layers in terms of long-range transport can be achieved using back trajectories from Lagrangian models, but care should be taken in selecting appropriate arrival heights, since the modelled and observed layer heights did not always coincide. We conclude that higher confidence in attributing elevated aerosol layers with their air mass origin is attained when back trajectories are combined with lidar and radiosonde profiles.

Determination of atmospheric aerosol particle size distribution and visibility using a mobile laboratory

1982 ◽  
Vol 60 (8) ◽  
pp. 1101-1107
Author(s):  
C. V. Mathai ◽  
A. W. Harrison
Keyword(s):  
Particle Size ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Atmospheric Aerosols ◽  
Suspended Particle ◽  
Aerosol Size Distribution ◽  
Size Distributions ◽  
Mobile Laboratory ◽  
Mean Values ◽  
The City

As part of an ongoing general research program on the effects of atmospheric aerosols on visibility and its dependence on aerosol size distributions in Calgary, this paper presents the results of a comparative study of particle size distribution and visibility in residential (NW) and industrial (SE) sections of the city using a mobile laboratory. The study was conducted in the period October–December, 1979. An active scattering aerosol spectrometer measured the size distributions and the corresponding visibilities were deduced from scattering coefficients measured with an integrating nephelometer.The results of this transit study show significantly higher suspended particle concentrations and reduced visibilities in the SE than in the NW. The mean values of the visibilities are 44 and 97 km for the SE and the NW respectively. The exponent of R (particle radius) in the power law aerosol size distribution has a mean value of −3.36 ± 0.24 in the SE compared with the corresponding value of −3.89 ± 0.39 for the NW. These results arc in good agreement with the observations of Alberta Environment; however, they are in contradiction with a recent report published by the City of Calgary.

scholarly journals An investigation of processes controlling the evolution of the boundary layer aerosol size distribution properties at the Swedish background station Aspvreten

2004 ◽  
Vol 4 (4) ◽  
pp. 4507-4543 ◽  
Author(s):  
P. Tunved ◽  
J. Ström ◽  
H.-C. Hansson
Keyword(s):  
Size Distribution ◽  
Wet Deposition ◽  
Source Area ◽  
Aerosol Size Distribution ◽  
Back Trajectory ◽  
Main Process ◽  
Size Distributions ◽  
Back Trajectory Analysis ◽  
The One ◽  
Precipitating Clouds

Abstract. Aerosol size distributions have been measured at the Swedish background station Aspvreten (58.8° N, 17.4° E). Different states of the aerosol were determined using a novel application of cluster analysis. The analysis resulted in eight different clusters capturing the different stages of the aerosol lifecycle. The aerosol was interpreted as belonging to fresh, intermediate and aged type of size distribution and different magnitudes thereof. With aid of back trajectory analysis we present statistics concerning the relation of source area and different meteorological parameters using a non-lagrangian approach. Source area is argued to be important although not sufficient to describe the observed aerosol properties. Especially processing by clouds and precipitation is shown to be crucial for the evolution of the aerosol size distribution. As much as 60% of the observed size distributions present features likely related to cloud processes or wet deposition. The lifetime properties of different sized aerosols are discussed by means of measured variability. Processing by non-precipitating clouds most obviously affect aerosols in the size range 100 nm and larger. This indicates an approximate limit for activation in clouds to 100 nm in this type of environment. The aerosol lifecycle is discussed. Size distributions bearing signs of recent new particle formation (~30% of the observed size distributions) represent the first stage in the lifecycle. Aging may proceed in two directions: either growth by condensation and coagulation or processing by non-precipitating clouds. In both cases mass is accumulated. Wet removal is the main process capable of removing aerosol mass. Wet deposition is argued to be an important mechanism in reaching a state where nucleation may occur (i.e. sufficiently low aerosol surface area) in environments similar to the one studied.

scholarly journals Quantifying aerosol size distributions and their temporal variability in the Southern Great Plains, USA

2019 ◽  
Vol 19 (18) ◽  
pp. 11985-12006 ◽  
Author(s):  
Peter J. Marinescu ◽  
Ezra J. T. Levin ◽  
Don Collins ◽  
Sonia M. Kreidenweis ◽  
Susan C. van den Heever
Keyword(s):  
Size Distribution ◽  
Great Plains ◽  
Diurnal Cycle ◽  
Particle Formation ◽  
Aerosol Size Distribution ◽  
Size Distributions ◽  
New Particle Formation ◽  
Scanning Mobility Particle Sizer ◽  
Southern Great Plains ◽  
Particle Sizer

Abstract. A quality-controlled, 5-year dataset of aerosol number size distributions (particles with diameters (Dp) from 7 nm through 14 µm) was developed using observations from a scanning mobility particle sizer, aerodynamic particle sizer, and a condensation particle counter at the Department of Energy's Southern Great Plains (SGP) site. This dataset was used for two purposes. First, typical characteristics of the aerosol size distribution (number, surface area, and volume) were calculated for the SGP site, both for the entire dataset and on a seasonal basis, and size distribution lognormal fit parameters are provided. While the median size distributions generally had similar shapes (four lognormal modes) in all the seasons, there were some significant differences between seasons. These differences were most significant in the smallest particles (Dp<30 nm) and largest particles (Dp>800 nm). Second, power spectral analysis was conducted on this long-term dataset to determine key temporal cycles of total aerosol concentrations, as well as aerosol concentrations in specified size ranges. The strongest cyclic signal was associated with a diurnal cycle in total aerosol number concentrations that was driven by the number concentrations of the smallest particles (Dp<30 nm). This diurnal cycle in the smallest particles occurred in all seasons in ∼50 % of the observations, suggesting a persistent influence of new particle formation events on the number concentrations observed at the SGP site. This finding is in contrast with earlier studies that suggest new particle formation is observed primarily in the springtime at this site. The timing of peak concentrations associated with this diurnal cycle was shifted by several hours depending on the season, which was consistent with seasonal differences in insolation and boundary layer processes. Significant diurnal cycles in number concentrations were also found for particles with Dp between 140 and 800 nm, with peak concentrations occurring in the overnight hours, which were primarily associated with both nitrate and organic aerosol cycles. Weaker cyclic signals were observed for longer timescales (days to weeks) and are hypothesized to be related to the timescales of synoptic weather variability. The strongest periodic signals (3.5–5 and 7 d cycles) for these longer timescales varied depending on the season, with no cyclic signals and the lowest variability in the summer.

scholarly journals Performance Assessment of Portable Optical Particle Spectrometer (POPS)

Sensors ◽  
2020 ◽  
Vol 20 (21) ◽  
pp. 6294
Author(s):  
Fan Mei ◽  
Gavin McMeeking ◽  
Mikhail Pekour ◽  
Ru-Shan Gao ◽  
Gourihar Kulkarni ◽  
...  
Keyword(s):  
High Sensitivity ◽  
Apparent Size ◽  
Aerosol Size Distribution ◽  
Size Distributions ◽  
Flow Temperature ◽  
Atmospheric Research ◽  
Miniaturized Instrumentation ◽  
Aerial Systems ◽  
Laser Heater

Accurate representation of atmospheric aerosol properties is a long-standing problem in atmospheric research. Modern pilotless aerial systems provide a new platform for atmospheric in situ measurement. However, small airborne platforms require miniaturized instrumentation due to apparent size, power, and weight limitations. A Portable Optical Particle Spectrometer (POPS) is an emerged instrument to measure ambient aerosol size distribution with high time and size resolution, designed for deployment on a small unmanned aerial system (UAS) or tethered balloon system (TBS) platforms. This study evaluates the performance of a POPS with an upgraded laser heater and additional temperature sensors in the aerosol pathway. POPS maintains its performance under different environmental conditions as long as the laser temperature remains above 25 °C and the aerosol flow temperature inside the optical chamber is 15 °C higher than the ambient temperature. The comparison between POPS and an Ultra-High Sensitivity Aerosol Spectrometer (UHSAS) suggests that the coincidence error is less than 25% when the number concentration is less than 4000 cm−3. The size distributions measured by both of them remained unaffected up to 15,000 cm−3. While both instruments’ sizing accuracy is affected by the aerosol chemical composition and morphology, the influence is more profound on the POPS.

scholarly journals Evaluating Model Parameterizations of Submicron Aerosol Scattering and Absorption with In Situ Data from ARCTAS 2008

2016 ◽  
Author(s):  
M. J. Alvarado ◽  
C. R. Lonsdale ◽  
H. L. Macintyre ◽  
H. Bian ◽  
M. Chin ◽  
...  
Keyword(s):  
Optical Properties ◽  
Size Distribution ◽  
Aerosol Size Distribution ◽  
Visible Radiation ◽  
Submicron Aerosol ◽  
In Situ Data ◽  
Aerosol Absorption ◽  
Aerosol Scattering ◽  
The Impact

Abstract. Accurate modeling of the scattering and absorption of ultraviolet and visible radiation by aerosols is essential for accurate simulations of atmospheric chemistry and climate. Closure studies using in situ measurements of aerosol scattering and absorption can be used to evaluate and improve models of aerosol optical properties without interference from model errors in aerosol emissions, transport, chemistry, or deposition rates. Here we evaluate the ability of four externally mixed, fixed size distribution parameterizations used in global models to simulate submicron aerosol scattering and absorption at three wavelengths using in situ data gathered during the 2008 Arctic Research of the Composition of the Troposphere from Aircraft and Satellites (ARCTAS) campaign. The four models are the NASA Global Modeling Initiative (GMI) Combo model, GEOS-Chem v9-02, the baseline configuration of a version of GEOS-Chem with online radiative transfer calculations (called GC-RT), and the Optical Properties of Aerosol and Clouds (OPAC v3.1) package. We also use the ARCTAS data to perform the first evaluation of the ability of the Aerosol Simulation Program (ASP v2.1) to simulate submicron aerosol scattering and absorption when in situ data on the aerosol size distribution is used, and examine the impact of different mixing rules for black carbon (BC) on the results. We find that the GMI model tends to overestimate submicron scattering and absorption at shorter wavelengths by 10–23 %, and that GMI has smaller absolute mean biases for submicron absorption than OPAC v3.1, GEOS-Chem v9-02, or GC-RT. However, the changes to the density and refractive index of BC in GC-RT improve the simulation of submicron aerosol absorption at all wavelengths relative to GEOS-Chem v9-02. Adding in situ size distribution information, as in ASP v2.1, improves model performance for scattering but not for absorption, likely due to the assumption in ASP v2.1 that BC is present at a constant mass fraction through out the aerosol size distribution. Using a core-shell mixing state in ASP overestimates aerosol absorption, especially for the fresh biomass burning aerosol measured in ARCTAS-B, suggesting the need for time-varying mixing states in future versions of ASP.

scholarly journals Microphysical properties of synoptic-scale polar stratospheric clouds: in situ measurements of unexpectedly large HNO<sub>3</sub>-containing particles in the Arctic vortex

2014 ◽  
Vol 14 (19) ◽  
pp. 10785-10801 ◽  
Author(s):  
S. Molleker ◽  
S. Borrmann ◽  
H. Schlager ◽  
B. Luo ◽  
W. Frey ◽  
...  
Keyword(s):  
Nitric Acid ◽  
Scattered Light ◽  
Stratospheric Ozone ◽  
The Arctic ◽  
Size Distributions ◽  
Synoptic Scale ◽  
Cloud Particle ◽  
Regular Feature ◽  
Particle Composition

Abstract. In January 2010 and December 2011, synoptic-scale polar stratospheric cloud (PSC) fields were probed during seven flights of the high-altitude research aircraft M-55 Geophysica within the RECONCILE (Reconciliation of essential process parameters for an enhanced predictability of Arctic stratospheric ozone loss and its climate interaction) and the ESSenCe (ESSenCe: ESA Sounder Campaign) projects. Particle size distributions in a diameter range between 0.46 and 40μm were recorded by four different optical in situ instruments. Three of these particle instruments are based on the detection of forward-scattered light by single particles. The fourth instrument is a grayscale optical array imaging probe. Optical particle diameters of up to 35μm were detected with particle number densities and total particle volumes exceeding previous Arctic measurements. Also, gas-phase and particle-bound NOy was measured, as well as water vapor concentrations. The optical characteristics of the clouds were measured by the remote sensing lidar MAL (Miniature Aerosol Lidar) and by the in situ backscatter sonde MAS (Multiwavelength Aerosol Scatterometer), showing the synoptic scale of the encountered PSCs. The particle mode below 2μm in size diameter has been identified as supercooled ternary solution (STS) droplets. The PSC particles in the size range above 2μm in diameter are considered to consist of nitric acid hydrates, and the particles' high HNO3 content was confirmed by the NOy instrument. Assuming a particle composition of nitric acid trihydrate (NAT), the optically measured size distributions result in particle-phase HNO3 mixing ratios exceeding available stratospheric values. Therefore the measurement uncertainties concerning probable overestimations of measured particle sizes and volumes are discussed in detail. We hypothesize that either a strong asphericity or an alternate particle composition (e.g., water ice coated with NAT) could explain our observations. In particular, with respect to the denitrification by sedimentation of large HNO3-containing particles, generally considered to be NAT, our new measurements raise questions concerning composition, shape and nucleation pathways. Answering these would improve the numerical simulation of PSC microphysical processes like cloud particle formation, growth and denitrification, which is necessary for better predictions of future polar ozone losses, especially under changing global climate conditions. Generally, it seems that the occurrence of large NAT particles – sometimes termed "NAT rocks" – are a regular feature of synoptic-scale PSCs in the Arctic.

Sign in / Sign up

Export Citation Format

Share Document