Physical–mechanical evaluation of a microhybrid and a nanofilled composite light activated by quartz-halogen tungsten and light-emitting diode

2018 ◽  
Vol 53 (7) ◽  
pp. 981-990
Author(s):  
Fernanda P Ritto ◽  
Eduardo Moreira da Silva ◽  
Hélio Rodrigues Sampaio-Filho ◽  
Raimundo A Lacerda ◽  
Márcio AP Borges ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Nuclear Magnetic Resonance ◽  
Light Emitting Diode ◽  
Degree Of Conversion ◽  
Dental Composite ◽  
Polymerization Shrinkage ◽  
Light Emitting ◽  
Scanning Electron

The aim of this study was to characterize organic and disperse phase of a microhybrid (Mh – Filtek Z250) and a nanofilled (Nf – Filtek Z350) dental composite and analyze the influence of two LCUs (QHT-quartz-halogen tungsten and LED – light-emitting diode) on its physical–mechanical properties (degree of conversion, polymerization shrinkage, Vickers hardness and diametral tensile strength). Surface morphology was studied by scanning electron microscopy. The disperse phase content was measured using thermogravimetric analysis (TGA) and the organic fractions were qualitatively analyzed by nuclear magnetic resonance spectroscopy. Physical–mechanical properties were analyzed varying dental composite and LCU: Mh-QHT, Nf-QHT, Mh-LED and Nf-LED. The degree of conversion was evaluated using Raman spectrophotometry and polymerization shrinkage was measured by water picnometry. Mechanical behavior was analyzed by Vickers microhardness and diametral tensile testing. Scanning electron microscopy analysis showed similar microstructure of the materials mainly composed with different-sized particles dispersed within methacrylate matrix. Thermogravimetric analysis shows 80.13% of inorganic fraction for microhybrid composite and 75.29% for nanofilled. Nuclear magnetic resonance analysis showed similar organic structure for composites and did not show the presence of the monomer TEGDMA. Different light sources did not influence the tested properties, but considering different composites, nanofilled showed the highest degree of conversion (Gr 2:77%, Gr 4: 79.4%). The study shows that when the optimum radiant exposure (24 J/cm2) was used for polymerization of composites, regardless of the polymerization source, the properties of these resin materials showed satisfactory and similar results in relation to the conversion of polymers, polymerization shrinkage and mechanical behavior.

Scanning Electron Microscopy Cathodoluminescence Studies of Piezoelectric Fields in an InGaN Multiple Quantum Well Light Emitting Diode

2004 ◽  
Vol 831 ◽  
Author(s):  
Kristin L. Bunker ◽  
Roberto Garcia ◽  
Phillip E. Russell
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Quantum Well ◽  
Light Emitting Diode ◽  
Multiple Quantum Well ◽  
Multiple Quantum ◽  
Light Emitting ◽  
Piezoelectric Field ◽  
Piezoelectric Fields ◽  
Scanning Electron

ABSTRACTScanning Electron Microscopy (SEM)-based Cathodoluminescence (CL) experiments were used to study the influence of piezoelectric fields on the optical and electrical properties of a commercial InGaN-based Multiple Quantum Well (MQW) Light Emitting Diode (LED). The existence and direction of a piezoelectric field in the InGaN-based LED was determined with voltage dependent SEM-CL experiments. The CL emission peak showed a blueshift followed by a redshift with increasing reverse bias due to the full compensation of the piezoelectric field. It was determined that the piezoelectric field points in the [000–1] direction and the magnitude was estimated to be approximately 1.0±0.2 MV/cm. SEM-CL carrier generation density variation and electroluminescence experiments were used to confirm the existence of a piezoelectric field in the InGaN-based MQW LED.

Electron Microscopic Observation of the Longitudinal Organization of Poly (p-Phenylene Terephthalamide) Fibers

1982 ◽  
Vol 40 ◽  
pp. 680-681
Author(s):  
Li Li-Sheng ◽  
L.F. Allard ◽  
W.C. Bigelow
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Microscopic Observation ◽  
Electron Microscopic Observation ◽  
Electron Microscopic ◽  
Aromatic Polyamides ◽  
Radial Arrangement ◽  
Scanning Electron ◽  
Better Than

The aromatic polyamides form a class of fibers having mechanical properties which are much better than those of aliphatic polyamides. Currently, the accepted morphology of these fibers as proposed by M.G. Dobb, et al. is a radial arrangement of pleated sheets, with the plane of the pleats parallel to the axis of the fiber. We have recently obtained evidence which supports a different morphology of this type of fiber, using ultramicrotomy and ion-thinning techniques to prepare specimens for transmission and scanning electron microscopy.

scholarly journals Analysis of PLA Composite Filaments Reinforced with Lignin and Polymerised-Lignin-Treated NFC

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2174
Author(s):  
Diana Gregor-Svetec ◽  
Mirjam Leskovšek ◽  
Blaž Leskovar ◽  
Urška Stanković Elesini ◽  
Urška Vrabič-Brodnjak
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Glassy State ◽  
Nanofibrillated Cellulose ◽  
Dynamic Mechanical Properties ◽  
Initial Modulus ◽  
Surface Modified ◽  
Scanning Electron

Polylactic acid (PLA) is one of the most suitable materials for 3D printing. Blending with nanoparticles improves some of its properties, broadening its application possibilities. The article presents a study of composite PLA matrix filaments with added unmodified and lignin/polymerised lignin surface-modified nanofibrillated cellulose (NFC). The influence of untreated and surface-modified NFC on morphological, mechanical, technological, infrared spectroscopic, and dynamic mechanical properties was evaluated for different groups of samples. As determined by the stereo and scanning electron microscopy, the unmodified and surface-modified NFCs with lignin and polymerised lignin were present in the form of plate-shaped agglomerates. The addition of NFC slightly reduced the filaments’ tensile strength, stretchability, and ability to absorb energy, while in contrast, the initial modulus slightly improved. By adding NFC to the PLA matrix, the bending storage modulus (E’) decreased slightly at lower temperatures, especially in the PLA samples with 3 wt% and 5 wt% NFC. When NFC was modified with lignin and polymerised lignin, an increase in E’ was noticed, especially in the glassy state.

scholarly journals Corrosion Behavior and Mechanical Properties of a Nanocomposite Superhydrophobic Coating

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 652
Author(s):  
Divine Sebastian ◽  
Chun-Wei Yao ◽  
Lutfun Nipa ◽  
Ian Lian ◽  
Gary Twu
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Atomic Force Microscopy ◽  
Nanocomposite Coating ◽  
Superhydrophobic Coating ◽  
Force Microscopy ◽  
Atomic Force ◽  
Microscopy Images ◽  
Scanning Electron

In this work, a mechanically durable anticorrosion superhydrophobic coating is developed using a nanocomposite coating solution composed of silica nanoparticles and epoxy resin. The nanocomposite coating developed was tested for its superhydrophobic behavior using goniometry; surface morphology using scanning electron microscopy and atomic force microscopy; elemental composition using energy dispersive X-ray spectroscopy; corrosion resistance using atomic force microscopy; and potentiodynamic polarization measurements. The nanocomposite coating possesses hierarchical micro/nanostructures, according to the scanning electron microscopy images, and the presence of such structures was further confirmed by the atomic force microscopy images. The developed nanocomposite coating was found to be highly superhydrophobic as well as corrosion resistant, according to the results from static contact angle measurement and potentiodynamic polarization measurement, respectively. The abrasion resistance and mechanical durability of the nanocomposite coating were studied by abrasion tests, and the mechanical properties such as reduced modulus and Berkovich hardness were evaluated with the aid of nanoindentation tests.

Research on compatibility and surface of high impact bio-based polyamide

2021 ◽  
pp. 095400832110055
Author(s):  
Yang Wang ◽  
Yuhui Zhang ◽  
Yuhan Xu ◽  
Xiucai Liu ◽  
Weihong Guo
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Crystallization Behavior ◽  
High Impact ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

The super-tough bio-based nylon was prepared by melt extrusion. In order to improve the compatibility between bio-based nylon and elastomer, the elastomer POE was grafted with maleic anhydride. Scanning Electron Microscopy (SEM) and Thermogravimetric Analysis (TGA) were used to study the compatibility and micro-distribution between super-tough bio-based nylon and toughened elastomers. The results of mechanical strength experiments show that the 20% content of POE-g-MAH has the best toughening effect. After toughening, the toughness of the super-tough nylon was significantly improved. The notched impact strength was 88 kJ/m2 increasing by 1700%, which was in line with the industrial super-tough nylon. X-ray Diffraction (XRD) and Differential Scanning Calorimetry (DSC) were used to study the crystallization behavior of bio-based PA56, and the effect of bio-based PA56 with high crystallinity on mechanical properties was analyzed from the microstructure.

scholarly journals Effect of Annealing Process on the Mechanical Properties of X70 Pipeline Steel

2018 ◽  
Vol 186 ◽  
pp. 02001
Author(s):  
Teng-wei Zhu ◽  
Cheng-liang Miao ◽  
Zheng Cheng ◽  
Zhipeng Wang ◽  
Yang Cui ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Annealing Temperature ◽  
Pipeline Steel ◽  
Annealing Process ◽  
X70 Pipeline Steel ◽  
Grain Sizes ◽  
Scanning Electron

The influence of the mechanical properties of X70 pipeline steel under different annealing temperature was studied. The corresponding microstructure was investigated by the Field Emission Scanning Electron Microscopy. The results showed that the yield strength and the tensile strength both experienced from rise to decline with the increase of annealing temperature. The grain sizes were coarse and a large amount of cementite precipitated due to preserving temperature above 550 °, which induced matrix fragmentation and deteriorate the -10 ° DWTT Toughness. There were little changes on the microstructure and mechanical properties when the annealing temperature was under 500 °.

Hierarchical Design and Nanomechanics of the Calcified Byssus of Anomia simplex

2009 ◽  
Vol 1187 ◽  
Author(s):  
Jakob R Eltzholtz ◽  
Marie Krogsgaard ◽  
Henrik Birkedal
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Mechanical Performance ◽  
Blue Mussel ◽  
Hierarchical Design ◽  
Reduced Modulus ◽  
Different Types ◽  
Microscopy Images ◽  
Scanning Electron

AbstractBiology has evolved several strategies for attachment of sedentary animals. In the bivalves, byssi abound and the best known example being the protein-based byssus of the blue mussel and other Mytilidae. In contrast the bivalve Anomia sp. has a single calcified thread. The byssus is hierarchical in design and contains several different types of structures as revealed by scanning electron microscopy images. The mechanical properties of the byssus are probed by nanoindentation. It is found that the mineralized part of the byssus is very stiff with a reduced modulus of about 67 GPa and a hardness of ˜3.7 GPa. This corresponds to a modulus roughly 20% smaller than that of pure calcite and a hardness that is about 20% larger than pure calcite. The results reveal the importance of microstructure on mechanical performance.

scholarly journals Polymeric Composites Based on Polyurea Matrix Reinforced with Carbon Nanotubes

2017 ◽  
Vol 54 (1) ◽  
pp. 41-44 ◽  
Author(s):  
Maria Adina Vulcan ◽  
Celina Damian ◽  
Paul Octavian Stanescu ◽  
Eugeniu Vasile ◽  
Razvan Petre ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Thermal Stability ◽  
Scanning Electron Microscopy ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Scanning Electron

This paper deals with the synthesis of polyurea and its use as polymer matrix for nanocomposites reinforced with multi-walled carbon nanotubes (MWCNT). Two types of materials were obtained during this research, the first cathegory uses the polyurea as matrix and the second one uses a mixture between epoxy resin and polyurea. The nanocomposites were characterized by Thermogravimetric Analysis (TGA), Dynamic Mechanical Analysis (DMA), Scanning Electron Microscopy (SEM) and Tensile Tests .The elastomeric features of nanocomposites were highlighted by the results which showed low value of Tg. Also higher thermal stability with ~40oC compared with commercial products (M20) were observed, but lower mechanical properties compared to neat polyurea.

Sign in / Sign up

Export Citation Format

Share Document