Hierarchical Design and Nanomechanics of the Calcified Byssus of Anomia simplex

2009 ◽  
Vol 1187 ◽  
Author(s):  
Jakob R Eltzholtz ◽  
Marie Krogsgaard ◽  
Henrik Birkedal
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Mechanical Performance ◽  
Blue Mussel ◽  
Hierarchical Design ◽  
Reduced Modulus ◽  
Different Types ◽  
Microscopy Images ◽  
Scanning Electron

AbstractBiology has evolved several strategies for attachment of sedentary animals. In the bivalves, byssi abound and the best known example being the protein-based byssus of the blue mussel and other Mytilidae. In contrast the bivalve Anomia sp. has a single calcified thread. The byssus is hierarchical in design and contains several different types of structures as revealed by scanning electron microscopy images. The mechanical properties of the byssus are probed by nanoindentation. It is found that the mineralized part of the byssus is very stiff with a reduced modulus of about 67 GPa and a hardness of ˜3.7 GPa. This corresponds to a modulus roughly 20% smaller than that of pure calcite and a hardness that is about 20% larger than pure calcite. The results reveal the importance of microstructure on mechanical performance.

scholarly journals Corrosion Behavior and Mechanical Properties of a Nanocomposite Superhydrophobic Coating

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 652
Author(s):  
Divine Sebastian ◽  
Chun-Wei Yao ◽  
Lutfun Nipa ◽  
Ian Lian ◽  
Gary Twu
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Atomic Force Microscopy ◽  
Nanocomposite Coating ◽  
Superhydrophobic Coating ◽  
Force Microscopy ◽  
Atomic Force ◽  
Microscopy Images ◽  
Scanning Electron

In this work, a mechanically durable anticorrosion superhydrophobic coating is developed using a nanocomposite coating solution composed of silica nanoparticles and epoxy resin. The nanocomposite coating developed was tested for its superhydrophobic behavior using goniometry; surface morphology using scanning electron microscopy and atomic force microscopy; elemental composition using energy dispersive X-ray spectroscopy; corrosion resistance using atomic force microscopy; and potentiodynamic polarization measurements. The nanocomposite coating possesses hierarchical micro/nanostructures, according to the scanning electron microscopy images, and the presence of such structures was further confirmed by the atomic force microscopy images. The developed nanocomposite coating was found to be highly superhydrophobic as well as corrosion resistant, according to the results from static contact angle measurement and potentiodynamic polarization measurement, respectively. The abrasion resistance and mechanical durability of the nanocomposite coating were studied by abrasion tests, and the mechanical properties such as reduced modulus and Berkovich hardness were evaluated with the aid of nanoindentation tests.

Evaluation of 4330M Steel for Fasteners Applications

2017 ◽  
Vol 380 ◽  
pp. 198-211 ◽  
Author(s):  
A. Al Sumait ◽  
C. Delgado ◽  
F. Aldhabib ◽  
X. Sun ◽  
F. Alzubi ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Testing ◽  
Grain Structure ◽  
Hardness Testing ◽  
Heat Treated ◽  
Different Types ◽  
Strength And Ductility ◽  
Scanning Electron

The objective of the study was to optimize the strength and ductility values of the 4330M steel. Optimization was conducted through different types of heat treatments. Tensile testing, hardness testing, optical microscopy, and Scanning Electron Microscopy (SEM) were used to evaluate the mechanical properties and microstructure of the as-received and the heat treated samples. The alloy was provided from two vendors; vendor H and vendor S. Results showed that by increasing the tempering temperatures, strength values decreases, while ductility values remain unchanged. Vendor H samples had higher strength values and much finer grain structure which was revealed only at 5000x magnification.

Effect of Nanocellulose Loading on Tensile Properties of Nitrile Rubber

2017 ◽  
Vol 264 ◽  
pp. 112-115
Author(s):  
Erfan Suryani Abdul Rashid ◽  
Wageeh Abdulhadi Yehye ◽  
Nurhidayatullaili Muhd Julkapli ◽  
Sharifah Bee O.A. Abdul Hamid
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Tensile Test ◽  
Tensile Properties ◽  
Mechanical Performance ◽  
Butadiene Rubber ◽  
Fracture Surfaces ◽  
Scanning Electron

Nanocellulose (NCC) is incorporated into nitrile butadiene rubber (NBR) latex with the composition 0 to 5 phr using dipping method. Mechanical properties of NBR/NCC composites using tensile test was used to characterize their mechanical performance and the fracture surfaces post tensile test were studied. The tensile strength of NBR/NCC composites increase significantly with the addition of nanocellulose. This could be anticipated due to the presence of Van der Waals interaction between hydrophilic natures of nanocellulose with hydrophobic of NBR consequently limits the tearing propagation. The result was supported with the fracture surfaces morphology viewed under Fourier Emission Scanning Electron Microscopy (FESEM).

scholarly journals Enhancement the Osseo Integration Properties of Polymer for Human Body Implants

2020 ◽  
Vol 23 (4) ◽  
pp. 331-337
Author(s):  
Dhurgham Majid Rasheed ◽  
Dunya Abdulsahib Hamdi
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Grain Boundaries ◽  
Mechanical Performance ◽  
Wear Test ◽  
High Energy ◽  
In Vitro Test ◽  
Scanning Electron

In this research, polymer polymethyl methacrylate PMMA composite with nano ceramic Zr and HAp material were used to manufacture one part of the implant system (femoral ball head of hip implant). Three set of hybrid materials were fabricated and tested for this study; the first mixtures which contains 100% (PMMA), the second mixtures which contains (90% (PMMA) + 8% (Zr) + 2% (HAp)), and the third mixtures which contains (80% (PMMA) + 18% (Zr) + 2% (HAp)) were investigated. The mechanical properties for these mixtures increased with the increasing of nano ceramic concentration (Zr and HAp) composite material in the polymer compared to pure polymer PMMA sample. However, an increase in the concentration of Zr from 8% to 18% content cause a considerable decrease of the hardness where a drop of homogeneity in Zr- matrix PMMA contact occurred, V Hardness value are (68 ,80 and 70) Kg.mm for three mixture respectively. The wear test was in agreement with results of the hardness test. The weight loss of the above samples of the wear test were (0.041, 0.035 and 0.037) respectively. According to mechanical properties, the best sample contains (90% (PMMA) + 8% (Zr) + 2% (HAp)). The Scanning electron microscopy resolute showed the particles forming semi-continuous network along grain boundaries polymer for second sample mixtures containing (90% (PMMA) + 8% (Zr) + 2% (HAp)), provides a low atomic packing and high energy. This will make the grain boundaries more reactive and strengthen mechanical performance. The Optical microscopy, Scanning electron microscopy and Xray spectroscopy analysis for In vitro test using SBF shows the growth of HAp layer with an increase in concentration of Ca and P elements formed on the surface of the second sample. This display of good results is a proof of the biocompatibility of the polymer sample.

Foam rubber from centrifuged and creamed latex

2019 ◽  
Vol 39 (4) ◽  
pp. 336-342 ◽  
Author(s):  
Rungrassamee Suksup ◽  
Yu Sun ◽  
Udomlak Sukatta ◽  
Wirasak Smitthipong
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Positive Impact ◽  
Rubber Content ◽  
Foam Rubber ◽  
Lower Porosity ◽  
Microscopy Images ◽  
Scanning Electron

Abstract The main aim of this work is to produce foam rubber using the Dunlop process from in-house creamed latex and compare it with commercial centrifuged latex. The dry rubber content of creamed latex is higher than that of fresh natural latex and traditional centrifuged latex. The creaming agent plays a major role during the preparation of foam rubber and therefore defines the density as well as the elastic and mechanical properties of the final product. Scanning electron microscopy images show lower porosity in rubber foam made from creamed latex compared to that from centrifuged latex. This methodology should have a highly positive impact on the rubber community in both upstream and downstream rubber industries.

Influence of the Microstructure on the Fracture Behavior of Carbon Bonded Alumina

2013 ◽  
Vol 592-593 ◽  
pp. 279-282 ◽  
Author(s):  
Stefan Soltysiak ◽  
Martin Abendroth ◽  
Meinhard Kuna ◽  
Steffen Dudczig
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Fracture Behavior ◽  
Small Punch Test ◽  
Open Cell ◽  
Small Punch ◽  
Punch Test ◽  
Different Types ◽  
Scanning Electron

Carbon bonded alumina (Al2O3-C) in various compositions are developed for the production of open cell filters, which are used for melt metal filtration processes [. The Small Punch Test (SPT) is used to determine the mechanical properties of such materials. Previous investigations showed two different types of fracture behavior [2,, which can be distinguished by typical features of the load deflection curves of the SPT. This paper clarifies this behavior by examining the fracture surfaces using scanning electron microscopy (SEM).

Evaluation of the effects of nanomaterials on durability of engineered cementitious composites exposed to the aggressive environment

2019 ◽  
Vol 54 (14) ◽  
pp. 1807-1817 ◽  
Author(s):  
Alireza Mansoori ◽  
Kiachehr Behfarnia
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Carbon Nanotube ◽  
Nano Silica ◽  
Aggressive Environment ◽  
Freeze And Thaw ◽  
Micro Silica ◽  
Microscopy Images ◽  
Scanning Electron

The present study was aimed to evaluate the effect of micro silica, nano silica and carbon nanotube in the engineered cementitious composites made with polyvinyl alcohol fibers. Accordingly, the compressive strength and the modulus of the samples rupture were studied to evaluate the impact of micro silica, nano silica and carbon nanotube in engineered cementitious composite. In addition, different curing conditions were considered to investigate the durability of the mixes. In this regard, the mechanical properties of the samples cured in sulphuric acid and freeze and thaw cycling were compared to those cured in water. The results indicated that the mechanical properties were reduced upon exposure to acid and freeze and thaw cycling. It was also found that the application of micro silica and nano silica made the mixtures compacted and reduced the permeability. The module of rupture was increased significantly by the addition of carbon nanotube. Moreover, the evaluation of the samples cured in the aggressive environment showed that the role of carbon nanotube was significant in increasing the durability of the mixes. Further, the scanning electron microscopy images showed that the crack width was reduced by the addition of carbon nanotube. It was also revealed from the scanning electron microscopy images that the polyvinyl alcohol fibers were completely interacted and connected to the paste.

scholarly journals New crosslinkers for electrospun chitosan fibre mats. Part II: mechanical properties

2013 ◽  
Vol 10 (81) ◽  
pp. 20120946 ◽  
Author(s):  
Amalie E. Donius ◽  
Marjorie A. Kiechel ◽  
Caroline L. Schauer ◽  
Ulrike G. K. Wegst
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Mechanical Performance ◽  
Fibre Diameter ◽  
Chemical Properties ◽  
Intermolecular Bonding ◽  
Crosslinking Agents ◽  
Scanning Electron

Few studies exist on the mechanical performance of crosslinked electrospun chitosan (CS) fibre mats. In this study, we show that the mat structure and mechanical performance depend on the different crosslinking agents genipin, epichlorohydrin (ECH), and hexamethylene-1,6-diaminocarboxysulphonate (HDACS), as well as the post-electrospinning heat and base activation treatments. The mat structure was imaged by field emission scanning electron microscopy and the mechanical performance was tested in tension. The elastic modulus, tensile strength, strain at failure and work to failure were found to range from 52 to 592 MPa, 2 to 30 MPa, 2 to 31 per cent and 0.041 to 3.26 MJ m −3 , respectively. In general, neat CS mats were found to be the stiffest and the strongest, though least ductile, while CS–ECH mats were the least stiff, weakest, but the most ductile, and CS–HDACS fibre mats exhibited intermediary mechanical properties. The mechanical performance of the mats is shown to reflect differences in the fibre diameter, number of fibre–fibre contacts formed within the mat, as well as varying intermolecular bonding and moisture content. The findings reported here complement the chemical properties of the mats, described in part I of this study.

Electron Microscopic Observation of the Longitudinal Organization of Poly (p-Phenylene Terephthalamide) Fibers

1982 ◽  
Vol 40 ◽  
pp. 680-681
Author(s):  
Li Li-Sheng ◽  
L.F. Allard ◽  
W.C. Bigelow
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Microscopic Observation ◽  
Electron Microscopic Observation ◽  
Electron Microscopic ◽  
Aromatic Polyamides ◽  
Radial Arrangement ◽  
Scanning Electron ◽  
Better Than

The aromatic polyamides form a class of fibers having mechanical properties which are much better than those of aliphatic polyamides. Currently, the accepted morphology of these fibers as proposed by M.G. Dobb, et al. is a radial arrangement of pleated sheets, with the plane of the pleats parallel to the axis of the fiber. We have recently obtained evidence which supports a different morphology of this type of fiber, using ultramicrotomy and ion-thinning techniques to prepare specimens for transmission and scanning electron microscopy.

Scanning electron microscopy of asbestos-containing material where the asbestos fibers are considered locked in a binder

1993 ◽  
Vol 51 ◽  
pp. 472-473
Author(s):  
J. R. Millette ◽  
R. S. Brown
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Environmental Protection Agency ◽  
Building Materials ◽  
The United States ◽  
Protection Agency ◽  
Asbestos Fibers ◽  
Different Types ◽  
Binder Material ◽  
Scanning Electron

The United States Environmental Protection Agency (EPA) has labeled as “friable” those building materials that are likely to readily release fibers. Friable materials when dry, can easily be crumbled, pulverized, or reduced to powder using hand pressure. Other asbestos containing building materials (ACBM) where the asbestos fibers are in a matrix of cement or bituminous or resinous binders are considered non-friable. However, when subjected to sanding, grinding, cutting or other forms of abrasion, these non-friable materials are to be treated as friable asbestos material. There has been a hypothesis that all raw asbestos fibers are encapsulated in solvents and binders and are not released as individual fibers if the material is cut or abraded. Examination of a number of different types of non-friable materials under the SEM show that after cutting or abrasion, tuffs or bundles of fibers are evident on the surfaces of the materials. When these tuffs or bundles are examined, they are shown to contain asbestos fibers which are free from binder material. These free fibers may be released into the air upon further cutting or abrasion.

Sign in / Sign up

Export Citation Format

Share Document