Modelling damage evolution and CAI strength of composite laminates under biaxial compression

2021 ◽  
pp. 002199832199842
Author(s):  
Bin Yang ◽  
Kunkun Fu ◽  
Yan Li
Keyword(s):  
Residual Strength ◽  
Composite Laminates ◽  
Failure Modes ◽  
Compressive Loading ◽  
Element Model ◽  
Low Velocity Impact ◽  
Biaxial Compression ◽  
Low Velocity ◽  
Damage Initiation ◽  
Compression After Impact

In this paper, a finite element model (FEM) was developed to investigate failure mechanism and compression after impact (CAI) strength of woven carbon fibre reinforced polymer (CFRP) after low-velocity impact (LVI) subjected to biaxial compressive loading. A built-in VUMAT user-defined material subroutine was adopted to take into account the in-plane damage and intralaminar delamination under LVI loading and in-plane compression. The LVI response, failure pattern, and residual mechanical properties under uniaxial compression were compared to the available experimental data to verify the numerical model. The damage initiation, subsequent evolution, final failure modes, and residual strength of the composite laminates with LVI damages subjected to biaxial compressive loading are presented by numerical methods, and the effects of impact energy and impactor diameter on the residual strength of the laminates are discussed.

Numerical Simulation of Compression-After-Impact Process of Composite Laminates

2012 ◽  
Vol 525-526 ◽  
pp. 265-268
Author(s):  
Biao Li ◽  
Ya Zhi Li ◽  
Xi Li ◽  
Zhen Hua Yao
Keyword(s):  
Composite Laminates ◽  
Element Model ◽  
Low Velocity Impact ◽  
Cohesive Elements ◽  
Low Velocity ◽  
Velocity Impact ◽  
Impact Process ◽  
Compression After Impact ◽  
Out Of Plane ◽  
Plane Compression

The residual compressive strength of composite laminates subjected to low-velocity impact (CAI) was analyzed using the ABAQUS/Explicit package through a two-step calculation. The finite element model was composed of solid elements and interfacial cohesive elements. The out of plane low-velocity impact process was simulated in the first step and the results of which were taken as the input for the second step of the in-plane compression, until the collapse of the laminate. The usefulness of the explicit solution algorithm in dealing with the quasi-static procedure of the in-plane compression was investigated by examining the effect of different initial velocities of the compression loading on CAI values. The simulation results agree well with the experimental results.

Development of a mathematical model to analyze residual strength of composites after low-velocity impact

2018 ◽  
Vol 53 (8) ◽  
pp. 738-745 ◽  
Author(s):  
Camila Medeiros Dantas de Azevedo ◽  
Rayane Dantas da Cunha ◽  
Raimundo Carlos Silverio Freire Junior ◽  
Wanderley Ferreira de Amorim Junior
Keyword(s):  
Residual Strength ◽  
Composite Laminates ◽  
Repair Process ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Velocity Impact ◽  
Three Point Bending ◽  
Compression After Impact ◽  
Strength And Stiffness ◽  
The Impact

This study aimed to develop a model to analyze the residual strength of composites after low-velocity impact, using three-point bending and compression after impact tests. Two types of composite laminates with an orthophthalic polymer matrix were used: one reinforced with bidirectional E-glass fabric and the other reinforced with bidirectional Kevlar-49 fabric. To that end, an equation was developed to assess loss of strength and stiffness after impact at different distances from the impact point, and this equation was not found in any previously searched article. The results demonstrate that the laminate based in glass fiber is more appropriate for the repair process.

Study on low-velocity impact and residual strength at high temperatures of composite laminates

2017 ◽  
Vol 233 (3) ◽  
pp. 1106-1123 ◽  
Author(s):  
Jingmeng Weng ◽  
Weidong Wen ◽  
Hongjian Zhang
Keyword(s):  
Compressive Strength ◽  
High Temperatures ◽  
Residual Strength ◽  
Composite Laminates ◽  
Impact Damage ◽  
Element Model ◽  
Low Velocity Impact ◽  
Cohesive Elements ◽  
Low Velocity ◽  
Velocity Impact

In this paper, low-velocity impact characteristics and residual tensile/compressive strength of composite laminates at high temperatures are experimentally and analytically investigated. Low-velocity impact tests at room temperature were performed using a drop-weight apparatus, and residual strength tests at high temperatures were performed using a hydraulic MTS machine. The experimental results show that both residual tensile and compressive strength decrease monotonically with the increase of impact energy, while the variation trend of residual tensile/compressive strength of composite laminates keeps the same with longitudinal tensile/compressive strength with the increase of temperature. In addition, a new stress-based delamination failure criterion was established, in which the delamination is considered to be controlled by the difference between through-thickness stresses of adjacent layers. Once delamination occurs, only the elements below the interface are marked with delamination, whereas the material properties of the elements on both sides of the interface are reduced simultaneously. In this way, delamination can be defined more precisely without cohesive elements, and a considerable reduction in CPU time can be achieved. Combined with extended Hashin failure criteria, an integrated finite element model was established to simulate low-velocity impact damage and to predict residual tensile and compressive strength of composite laminates. The numerical results show good agreements with experimental data.

Experimental Investigation of Impacted and Non-Impacted Composite Laminates under Compressive Loading

2011 ◽  
Vol 284-286 ◽  
pp. 607-610
Author(s):  
Jiang Tao Ruan ◽  
Min Shen ◽  
Jing Wei Tong ◽  
Shi Bin Wang ◽  
Francesco Aymerich ◽  
...  
Keyword(s):  
Composite Laminates ◽  
Optical Measurement ◽  
Speckle Pattern ◽  
Compressive Loading ◽  
Laminated Plates ◽  
Low Velocity Impact ◽  
Compressive Deformation ◽  
Electronic Speckle Pattern Interferometry ◽  
Low Velocity ◽  
The Impact

In this paper, the deformation measurements of impacted and non-impacted composite laminates under compressive loading are taken. [03/903]S orientated cross-ply laminated plates with impact delamination and without delamination are tested using an anti-buckling testing device in compression experiment. The delamination is induced by low-velocity impact test at the impact energy level of 3.105J. For both impacted and non-impacted specimens, the compressive deformation is measured by a carrier electronic speckle pattern interferometry (CESPI) optical measurement technique. It is found that the deformation behavior of the two specimens presents a mixed deformation mode. However, the delamination has significant effect on the compressive deformation of composite laminates.

Analysis on Low Velocity Impact Damage and Compressive Residual Strength of Composite Laminates

2014 ◽  
Vol 566 ◽  
pp. 463-467
Author(s):  
Pu Xue ◽  
H.H. Chen ◽  
W. Guo
Keyword(s):  
Experimental Data ◽  
Residual Strength ◽  
Composite Laminates ◽  
Damage Mechanics ◽  
Impact Damage ◽  
Numerical Results ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Velocity Impact ◽  
The Impact

This paper studies the impact damage under low velocity impact for composite laminates based on a nonlinear progressive damage model. Damage evolution is described by the framework of the continuum damage mechanics. The real impact damage status of composite laminates has been used to analyze the residual compressive strength instead of assumptions on damage area after impact. The validity of the methodologies has been demonstrated by comparing the numerical results with the experimental data available in literature. The delamination area has an error of 11.3%. The errors of residual strength and compressive displacement are 8.9% and 15%, which indicate that the numerical results matched well with the experimental data.

scholarly journals Palliatives for Low Velocity Impact Damage in Composite Laminates

2017 ◽  
Vol 2017 ◽  
pp. 1-16 ◽  
Author(s):  
Mubarak Ali ◽  
S. C. Joshi ◽  
Mohamed Thariq Hameed Sultan
Keyword(s):  
Composite Laminates ◽  
Impact Damage ◽  
Laminated Composites ◽  
Low Velocity Impact ◽  
Normal Operation ◽  
Fibre Reinforcement ◽  
Low Velocity ◽  
Velocity Impact ◽  
Damage Initiation ◽  
The Impact

Fibre reinforced polymer laminated composites are susceptible to impact damage during manufacture, normal operation, maintenance, and/or other stages of their life cycle. Initiation and growth of such damage lead to dramatic loss in the structural integrity and strength of laminates. This damage is generally difficult to detect and repair. This makes it important to find a preventive solution. There has been abundance of research dealing with the impact damage evolution of composite laminates and methods to mitigate and alleviate the damage initiation and growth. This article presents a comprehensive review of different strategies dealing with development of new composite materials investigated by several research groups that can be used to mitigate the low velocity impact damage in laminated composites. Hybrid composites, composites with tough thermoplastic resins, modified matrices, surface modification of fibres, translaminar reinforcements, and interlaminar modifications such as interleaving, short fibre reinforcement, and particle based interlayer are discussed in this article. A critical evaluation of various techniques capable of enhancing impact performance of laminated composites and future directions in this research field are presented in this article.

A damage mechanics model for low-velocity impact damage analysis of composite laminates

2017 ◽  
Vol 121 (1238) ◽  
pp. 515-532 ◽  
Author(s):  
N. Li ◽  
P.H. Chen ◽  
Q. Ye
Keyword(s):  
Composite Laminates ◽  
Damage Mechanics ◽  
Failure Modes ◽  
Impact Damage ◽  
Matrix Cracking ◽  
Low Velocity Impact ◽  
Fracture Plane ◽  
Low Velocity ◽  
Velocity Impact ◽  
The Impact

ABSTRACTA method was developed to predict numerically the damage of composite laminates with multiple plies under low-velocity impact loading. The Puck criterion for 3D stress states was adopted to model the intralaminar damage including matrix cracking and fibre breakage, and to obtain the orientation of the fracture plane due to matrix failure. According to interlaminar delamination mechanism, a new delamination criterion was proposed. The influence of transverse and through-thickness normal stress, interlaminar shear stress and damage conditions of adjacent plies on delamination was considered. In order to predict the impact-induced damage of composite laminates with more plies quickly and efficiently, an approach, which can predict the specific damage of several plies in a single solid element, was proposed by interpolation on the strains of element integration points. Moreover, the proposed model can predict specific failure modes. A good agreement between the predicted delamination shapes and sizes and the experimental results shows correctness of the developed numerical method for predicting low-velocity impact damage on composite laminates.

Sign in / Sign up

Export Citation Format

Share Document