Novel shape-memory polyurethane fibers for textile applications

2018 ◽  
Vol 89 (6) ◽  
pp. 1027-1037 ◽  
Author(s):  
Míriam Sáenz-Pérez ◽  
Tariq Bashir ◽  
José Manuel Laza ◽  
Jorge García-Barrasa ◽  
José Luis Vilas ◽  
...  
Keyword(s):  
Differential Scanning Calorimetry ◽  
Shape Memory ◽  
Tensile Testing ◽  
Melt Spinning ◽  
Mechanical Analysis ◽  
Knitted Fabric ◽  
Scanning Calorimetry ◽  
Moisture Management ◽  
Potential Applications ◽  
Shape Memory Polyurethane

In this work, thermoresponsive shape-memory polyurethane (SMPU) fibers were produced by melt spinning from different SMPU pellets. Afterwards, the knitted fabric samples were prepared by the obtained fibers. Some of the SMPUs used were synthesized previously in our laboratory whereas a commercial one, named DIAPLEX MM4520, was also evaluated in order to carry out comparative studies. All the SMPUs were characterized by different techniques, such as thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical analysis and tensile testing. Moreover, the shape-memory capabilities of the fabrics were measured by thermo-mechanical analysis. The obtained results show that the synthesized SMPUs could be attractive candidates for potential applications such as breathable fabrics or moisture-management textiles.

scholarly journals Combined thermal analysis of plant oils

2021 ◽  
Author(s):  
Kinga Tamási ◽  
Kálmán Marossy
Keyword(s):  
Thermal Analysis ◽  
Differential Scanning Calorimetry ◽  
Low Temperature ◽  
Glassy State ◽  
Mechanical Analysis ◽  
Plant Oils ◽  
Scanning Calorimetry ◽  
Natural Plant ◽  
The Moment ◽  
Current Reversal

AbstractThe paper deals with the study of seven selected natural plant oils. Differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and thermally stimulated discharge (TSD) methods were used. It has been found that most of the oils tested are in a glassy state at low temperature and have multiple transitions in the low temperature range. DSC shows complex melting-like processes or glass transition. For both DMA and TSD, the scaffold supportive method was used and found as a suitable one. DMA and TSD proved more sensitive than DSC and revealed at least two transitions between − 120 and − 40 °C. In the case of three oils (argan, avocado and sunflower), current reversal was observed by TSD; this symptom cannot be fully explained at the moment.

Physico Chemical Characterization of Nanofibrous Poly(Ε-Caprolactone) Electrospun Templates for Cell Adhesion

MRS Advances ◽  
2017 ◽  
Vol 2 (49) ◽  
pp. 2689-2694
Author(s):  
Karla A. Gaspar-Ovalle ◽  
Juan V. Cauich-Rodriguez ◽  
Armando Encinas
Keyword(s):  
Mechanical Properties ◽  
Differential Scanning Calorimetry ◽  
Cell Adhesion ◽  
Tensile Modulus ◽  
Chemical Characterization ◽  
Mechanical Analysis ◽  
Scanning Calorimetry ◽  
Water Contact ◽  
Physico Chemical ◽  
Static Water

ABSTRACTNanofibrous mats of poly ε-caprolactone (PCL) were fabricated by electrospinning. The nanofiber structures were investigated and characterized by scanning electron microscope, differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical analysis, static water-contact-angle analysis and mechanical properties. The results showed that the nanofibrous PCL is an ideal biopolymer for cell adhesion, owing to its biocompatibility, biodegradability, structural stability and mechanical properties. Differential scanning calorimetry results showed that the fibrous structure of PCL does not alter its crystallinity. Studies of the mechanical properties, wettability and degradability showed that the structure of the electrospun PCL improved the tensile modulus, tensile strength, wettability and biodegradability of the nanotemplates. To evaluate the nanofibrous structure of PCL on cell adhesion, osteoblasts cells were seeded on these templates. The results showed that both adhesion and proliferation of the cells is viable on these electrospun PCL membranes. Thus electrospinning is a relatively inexpensive and scalable manufacturing technique for submicron to nanometer diameter fibers, which can be of interest in the commodity industry.

Effect of Electroplastic Deformation on Martensitic Transformation in Coarse Grained and Ultrafine Grained Ni-Ti Shape Memory Alloy

2008 ◽  
Vol 584-586 ◽  
pp. 127-132 ◽  
Author(s):  
Anastasia E. Sergeeva ◽  
Daria Setman ◽  
Michael Zehetbauer ◽  
Sergey Prokoshkin ◽  
Vladimir V. Stolyarov
Keyword(s):  
Differential Scanning Calorimetry ◽  
Martensitic Transformation ◽  
Shape Memory Alloy ◽  
Cold Rolling ◽  
Shape Memory ◽  
Coarse Grained ◽  
Scanning Calorimetry ◽  
Structure Relaxation ◽  
Differential Scanning Calorimetry Method ◽  
Ultrafine Grained

The aim of this paper is the investigation of electroplastic deformation (EPD) and subsequent annealing influence on martensitic transformation in the shape memory Ni50.7Ti49.3 alloy. Using differential scanning calorimetry method it was shown that EPD at the low strain stimulates structure relaxation and recovers martensitic transformation in cooling, which is usually suppressed by cold rolling.

scholarly journals Nanocrystal, phase transformation and microstructure of Ni50Ti50 shape memory alloy

2018 ◽  
Vol 24 (02) ◽  
pp. 22-25
Author(s):  
Dovchinvanchig M ◽  
Chunwang Zhao
Keyword(s):  
Differential Scanning Calorimetry ◽  
Phase Transformation ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
One Step ◽  
Niti Matrix ◽  
Electronic Microscope

The nanocrystal, phase transformation and microstructure behavior of Ni50Ti50 shape memory alloy was investigated by scanning electronic microscope, X-ray diffraction and differential scanning calorimetry. The results showed that the microstructure of Ni-Ti binary alloy consists of the NiTi2 phase and the NiTi matrix phase. One-step phase transformation was observed alloy.

Fine structure formation and physical properties of poly(butylene terephthalate) fibres in high-speed melt spinning

e-Polymers ◽  
2003 ◽  
Vol 3 (1) ◽  
Author(s):  
Hee Lee Sun ◽  
Hou Kim Kyoung ◽  
Kikutani Takeshi ◽  
Hok Cho Hyun
Keyword(s):  
Fine Structure ◽  
Physical Properties ◽  
Structure Formation ◽  
High Speed ◽  
Melt Spinning ◽  
Mechanical Analysis ◽  
Scanning Calorimetry ◽  
Butylene Terephthalate ◽  
Initial Modulus ◽  
Higher Temperature

Abstract Poly(butylene terephthalate) (PBT) fibres were obtained by high-speed melt spinning up to a take-up velocity of 8 km/min. Fine structure formation and physical properties of these fibres were investigated. The increase of take-up velocity caused raises in both density and birefringence. In wide-angle X-ray diffraction equatorial profiles, the increase of take-up velocity can be observed in the (010) and (100) reflections of β-crystals; the reflection peaks are the sharpest at a take-up velocity of 6 km/min. The initial modulus of the fibres arises when the fraction of β-crystals is increased, while the tenacity depends more on the fraction of α-crystals, i.e., the total crystallinity. Thermal properties of high-speed spun PBT fibres were measured with differential scanning calorimetry, dynamic mechanical and thermo-mechanical analysis, etc. Endothermic curves become sharper with increasing take-up velocity, and endothermic melting peaks are shifted to higher temperature. Crystal structures are well developed in fibres obtained at higher take-up velocities. The tan δ peaks of PBT fibres tend to shift to higher temperature and the peak intensity is decreased with increasing take-up velocity, i.e., the packing density of PBT fibres is high when the take-up velocity and thus the orientation of amorphous regions is increased. The shrinkage has a tendency to decrease with increasing take-up velocity.

scholarly journals The Effect of POSS Type on the Shape Memory Properties of Epoxy-Based Nanocomposites

Molecules ◽  
2020 ◽  
Vol 25 (18) ◽  
pp. 4203
Author(s):  
Avraham I. Bram ◽  
Irina Gouzman ◽  
Asaf Bolker ◽  
Noam Eliaz ◽  
Ronen Verker
Keyword(s):  
Transition Temperature ◽  
Shape Memory ◽  
Crosslinking Density ◽  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Space Environment ◽  
Scanning Calorimetry ◽  
Space Applications ◽  
Curing Conditions ◽  
Oligomeric Silsesquioxane

Thermally activated shape memory polymers (SMPs) can memorize a temporary shape at low temperature and return to their permanent shape at higher temperature. These materials can be used for light and compact space deployment mechanisms. The control of transition temperature and thermomechanical properties of epoxy-based SMPs can be done using functionalized polyhedral oligomeric silsesquioxane (POSS) additives, which are also known to improve the durability to atomic oxygen in the space environment. In this study, the influence of varying amounts of two types of POSS added to epoxy-based SMPs on the shape memory effect (SME) were studied. The first type contained amine groups, whereas the second type contained epoxide groups. The curing conditions were defined using differential scanning calorimetry and glass transition temperature (Tg) measurements. Thermomechanical and SME properties were characterized using dynamic mechanical analysis. It was found that SMPs containing amine-based POSS show higher Tg, better shape fixity and faster recovery speed, while SMPs containing epoxide-based POSS have higher crosslinking density and show superior thermomechanical properties above Tg. This work demonstrates how the Tg and SME of SMPs can be controlled by the type and amount of POSS in an epoxy-based SMP nanocomposite for future space applications.

scholarly journals Bio-Based Epoxy Shape-Memory Thermosets from Triglycidyl Phloroglucinol

Polymers ◽  
2020 ◽  
Vol 12 (3) ◽  
pp. 542 ◽  
Author(s):  
David Santiago ◽  
Dailyn Guzmán ◽  
Francesc Ferrando ◽  
Àngels Serra ◽  
Silvia De la Flor
Keyword(s):  
Shape Memory ◽  
Shape Recovery ◽  
Memory Performance ◽  
Crosslinking Agent ◽  
Shape Memory Polymers ◽  
Crosslinking Density ◽  
Mechanical Analysis ◽  
Diglycidyl Ether ◽  
Partial Substitution ◽  
Scanning Calorimetry

A series of bio-based epoxy shape-memory thermosetting polymers were synthesized starting from a triglycidyl phloroglucinol (3EPOPh) and trimethylolpropane triglycidyl ether (TPTE) as epoxy monomers and a polyetheramine (JEF) as crosslinking agent. The evolution of the curing process was studied by differential scanning calorimetry (DSC) and the materials obtained were characterized by means of DSC, thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), stress-strain tests, and microindentation. Shape-memory properties were evaluated under free and totally constrained conditions. All results were compared with an industrial epoxy thermoset prepared from standard diglycidyl ether of Bisphenol A (DGEBA). Results revealed that materials prepared from 3EPOPh were more reactive and showed a tighter network with higher crosslinking density and glass transition temperatures than the prepared from DGEBA. The partial substitution of 3EPOPh by TPTE as epoxy comonomer caused an increase in the molecular mobility of the materials but without worsening the thermal stability. The shape-memory polymers (SMPs) prepared from 3EPOPh showed good mechanical properties as well as an excellent shape-memory performance. They showed almost complete shape-recovery and shape-fixation, fast shape-recovery rates, and recovery stress up to 7 MPa. The results obtained in this study allow us to conclude that the triglycidyl phloroglucinol derivative of eugenol is a safe and environmentally friendly alternative to DGEBA for preparing thermosetting shape-memory polymers.

Sign in / Sign up

Export Citation Format

Share Document