Modal and harmonic analysis of three-dimensional wind turbine models

2016 ◽  
Vol 40 (6) ◽  
pp. 518-527 ◽  
Author(s):  
Takwa Sellami ◽  
Hanen Berriri ◽  
A Moumen Darcherif ◽  
Sana Jelassi ◽  
M Faouizi Mimouni
Keyword(s):  
Finite Element ◽  
Wind Turbine ◽  
Natural Frequencies ◽  
Equations Of Motion ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Dynamic Responses ◽  
Mode Shapes ◽  
Element Analysis ◽  
Micro Turbine

In this article, the dynamic responses of wind turbine systems are analytically and numerically investigated. For this purpose, analytic differential equations of motion of wind turbine components subjected to vibration (the blades, the nacelle, and the tower) are solved. This allows determining their dynamic characteristics, mode shapes, and natural frequencies. Two models of two three-dimensional (3D) micro-turbine that are created by the finite element method are set up using the new version of the academic finite element analysis software ANSYS. The first wind turbine is a standard micro three-bladed turbine and the second one is a micro six-bladed Rutland 504. Their natural frequencies and mode shapes are identified based on the modal analysis principle to check the validity of designed models. Dynamic behaviors at several operating conditions of wind turbines are established. Then, spectrum graphs of the structures along x-, y- and z-axis are analyzed.

Investigation of stiffness of small wind turbine blade based on vibration analysis technique

2019 ◽  
Vol 44 (1) ◽  
pp. 49-59
Author(s):  
Nilesh Chandgude ◽  
Nitin Gadhave ◽  
Ganesh Taware ◽  
Nitin Patil
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Wind Turbine ◽  
Natural Frequency ◽  
Vibration Analysis ◽  
Natural Frequencies ◽  
Mode Shapes ◽  
Element Analysis ◽  
Finite Element Software ◽  
Small Wind Turbine

In this article, three small wind turbine blades of different materials were manufactured. Finite element analysis was carried out using finite element software ANSYS 14.5 on modeled blades of National Advisory Committee for Aeronautics 4412 airfoil profile. From finite element analysis, first, two flap-wise natural frequencies and mode shapes of three different blades are obtained. Experimental vibration analysis of manufactured blades was carried out using fast Fourier transform analyzer to find the first two flap-wise natural frequencies. Finally, the results obtained from the finite element analysis and experimental test of three blades are compared. Based on vibration analysis, we found that the natural frequency of glass fiber reinforced plastic blade reinforced with aluminum sheet metal (small) strips increases compared with the remaining blades. An increase in the natural frequency indicates an increase in the stiffness of blade.

scholarly journals Free Vibration Analysis of Cable Stayed-Bridge by Finite Element Method

2019 ◽  
Vol 12 (4) ◽  
pp. 67-72
Author(s):  
Haneen A. Mahmood ◽  
Zaid S. Hammoudi ◽  
Ali Laftah Abbas
Keyword(s):  
Finite Element ◽  
Free Vibration ◽  
Vibration Analysis ◽  
Natural Frequencies ◽  
Three Dimensional ◽  
Free Vibration Analysis ◽  
Element Model ◽  
Dynamic Responses ◽  
Mode Shapes ◽  
Cable Stayed Bridge

A delicate analysis of the natural frequencies and mode shapes of a cable stayed bridge is essential to the solution of its dynamic responses due to seismic, wind and traffic loads. In this paper, a bridge with geometry comparable to the Quincy Bayview Bridge was modelled in order to explore the significance of the three dimensional and free vibration analysis. This paper provides a detail of the bridge and the equivalent cross section of the three-dimensional finite element model implicating cables, the bridge deck and pylons as well as the boundary conditions and free vibration analysis by Ansys15.0. The bridge was analyzed to free vibration to obtaine the natural frequency and mode shape. result of this paper present the natural frequencies and mode shapes of the bridge. The method of modelling cables is also studied. It is found that modelling cables as multi beam elements provides better results than using the traditional (and simpler) method of modeling them as single tensile elements.

Dynamic Analysis of Large-Scale Power House

2012 ◽  
Vol 446-449 ◽  
pp. 837-840
Author(s):  
Yu Zhao ◽  
Shu Fang Yuan ◽  
Jian Wei Zhang
Keyword(s):  
Finite Element ◽  
Dynamic Characteristics ◽  
Large Scale ◽  
Three Dimensional ◽  
Dynamic Responses ◽  
Dynamic Loads ◽  
Element Analysis ◽  
Power House ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

The underwater structure of power house is major structure under the dynamic loads of unit. The vibration problem is very common in operation. So the structures should have sufficient stiffness to resist dynamic loads of unit. This paper establishes three-dimensional finite element models with finite element analysis software—ANSYS. Dynamic characteristics of the power house and dynamic responses of structure under earthquake are analyzed. The results of the computation show that fluid-solid coupling may be ignored when studying dynamic characteristics of structures of the underground power house.

Finite Element Analysis of Elliptical Chord

2013 ◽  
Vol 3 (4) ◽  
pp. 44-61
Author(s):  
K. S. Narayana ◽  
R. T. Naik ◽  
R. C. Mouli ◽  
L. V. V. Gopala Rao ◽  
R. T. Babu Naik
Keyword(s):  
Finite Element ◽  
Natural Frequencies ◽  
Three Dimensional ◽  
Compressive Load ◽  
Dynamic Strength ◽  
Element Analysis ◽  
T Joints ◽  
Shell Elements ◽  
Tubular Joints ◽  
Plane Bending

The work presents the Finite element study of the effect of elliptical chords on the static and dynamic strength of tubular T-joints using ANSYS. Two different geometry configurations of the T-joints have been used, namely Type-1 and Type-2. An elastic analysis has been considered. The Static loading conditions used are: axial load, compressive load, In-plane bending (IPB) and Out-plane bending (OPB). The natural frequencies analysis (dynamic loading condition) has also been carried out. The geometry configurations of the T-joints have been used, vertical tubes are called brace and horizontal tubes are called chords. The joint consists of brace joined perpendicular to the circular chord. In this case the ends of the chord are held fixed. The material used is mild steel. Using ANSYS, finite element modeling and analysis of T-joint has been done under the aforementioned loading cases. It is one of the most powerful methods in use but in many cases it is an expensive analysis especially due to elastic–plastic and creep problems. Usually, three dimensional solid elements or shell elements or the combination of two types of elements are used for generating the tubular joints mesh. In tubular joints, usually the fluid induced vibrations cause the joint to fail under resonance. Therefore the natural frequencies analysis is also an important issue here. Generally the empirical results are required as guide or comparison tool for finite element investigation. It is an effective way to obtain confidence in the results derived. Shell elements have been used to model the assembled geometry. Finite element ANSYS results have been validated with the LUSAS FEA and experimental results, that is within the experimentation error limit of ten percentage.

Free Vibration Analysis of PZT Glide Heads

1999 ◽  
Vol 121 (4) ◽  
pp. 984-988 ◽  
Author(s):  
Alex Y. Tsay ◽  
Jin-Hui Ouyang ◽  
C.-P. Roger Ku ◽  
I. Y. Shen ◽  
David Kuo
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Natural Frequencies ◽  
Laser Doppler Vibrometer ◽  
Free Vibration Analysis ◽  
Mode Shapes ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Bonding Length ◽  
Measured Displacement

This paper studies natural frequencies and mode shapes of a glide head with a piezoelectric transducer (PZT) through calibrated experiments and a finite element analysis. In the experiments, the PZT transducer served as an actuator exciting the glide head from 100 kHz to 1.3 MHz, and a laser Doppler vibrometer (LDV) measured displacement of the glide head at the inner or outer rail. The natural frequencies were measured through PZT impedance and frequency response functions from PZT to LDV. In the finite element analysis, the glide head was meshed by brick elements. The finite element results show that there are two types of vibration modes: slider modes and PZT modes. Only the slider modes are important to glide head applications. Moreover, natural frequencies predicted from the finite element analysis agree well with the experimental results within 5% of error. Finally, the finite element analysis identifies four critical slider dimensions whose tolerance will significantly vary the natural frequencies: PZT bonding length, wing thickness, slider thickness, and air bearing recess depth.

scholarly journals New Analytical Model Used in Finite Element Analysis of Solids Mechanics

Mathematics ◽  
2020 ◽  
Vol 8 (9) ◽  
pp. 1401 ◽  
Author(s):  
Sorin Vlase ◽  
Adrian Eracle Nicolescu ◽  
Marin Marin
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Equations Of Motion ◽  
Classical Mechanics ◽  
Three Dimensional ◽  
Elastic Solid ◽  
The Finite Element Method ◽  
Governing Equations ◽  
Element Analysis ◽  
Elastic Multibody System

In classical mechanics, determining the governing equations of motion using finite element analysis (FEA) of an elastic multibody system (MBS) leads to a system of second order differential equations. To integrate this, it must be transformed into a system of first-order equations. However, this can also be achieved directly and naturally if Hamilton’s equations are used. The paper presents this useful alternative formalism used in conjunction with the finite element method for MBSs. The motion equations in the very general case of a three-dimensional motion of an elastic solid are obtained. To illustrate the method, two examples are presented. A comparison between the integration times in the two cases presents another possible advantage of applying this method.

Modal Analysis Based on Finite Element Jaw Crusher Rotor

2014 ◽  
Vol 599-601 ◽  
pp. 547-550
Author(s):  
Mei Ling Hao ◽  
Guang Juan Cheng
Keyword(s):  
Finite Element ◽  
Modal Analysis ◽  
Natural Frequencies ◽  
Weak Link ◽  
Three Dimensional ◽  
Mode Shapes ◽  
Complex Dynamic ◽  
Three Dimensional Modeling ◽  
Dimensional Modeling ◽  
Analysis Of Results

The vertical shaft impact crusher the material is accelerated , while the rotor bear complex dynamic loads , finite element method for three-dimensional modeling of the rotor body and modal analysis , discussion and analysis of results. Won the first 20 natural frequencies and mode shapes , as well as the weak link parts may exist , making the crusher prone resonance attention away from the source at work , as well as designers kinetic design provides some guidance basis.

scholarly journals Evaluation of Basalt Fibers on Wind Turbine Blades through Finite Element Analysis

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
V. García ◽  
L. Vargas ◽  
A. Acuña ◽  
J. B. Sosa ◽  
E. Durazo ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Wind Turbine ◽  
Material Properties ◽  
Turbine Blades ◽  
Operating Conditions ◽  
Basalt Fibers ◽  
Wind Turbine Blades ◽  
Element Analysis ◽  
Structural Requirements

Here we use finite element analysis to determine the suitability of basalt fiber as a substitute for E-glass in structural applications, which would improve the cost effectiveness of small wind turbine blades. Five NACA (National Advisory Committee for Aeronautics) profiles were evaluated to select the optimum shape for the wind operation conditions. To obtain the wind load pressure distribution over the blade, a computational aerodynamic analysis by CFD (computational fluid dynamics) was performed based on the blade’s design and operating conditions. Material properties and mechanical tests were carried out to obtain the fiber volume fraction, density, Young’s modulus, shear modulus, and Poisson relation of polymeric matrix composites made using basalt and fiberglass. The obtained wind loads and material properties were used on a FEM (finite element model) analysis to evaluate the structural behavior of the blade under normal and critical operating conditions. Both fibers meet the structural requirements under normal operating conditions. We detected a reduction of 4% in the blade stress when basalt fibers are used instead of glass fibers, and a reduction of 68% in the total deformation for a critical load case of 40 m/s was obtained when using basalt fibers, which met the structural requirements and maximum power generation required for this wind turbine design.

Modal Analysis of Ballooning Strings With Small Sag

1999 ◽  
Author(s):  
Rongjun Fan ◽  
Sushil K. Singh ◽  
Christopher D. Rahn
Keyword(s):  
Steady State ◽  
High Speed ◽  
Natural Frequencies ◽  
Rotation Speed ◽  
Equations Of Motion ◽  
Three Dimensional ◽  
Mode Shapes ◽  
Theoretical Predictions ◽  
Nonlinear Equations Of Motion

Abstract During the manufacture and transport of textile products, yarns are rotated at high speed and form balloons. The dynamic response of the balloon to varying rotation speed, boundary excitation, and disturbance forces governs the quality of the associated process. Resonance, in particular, can cause large tension variations that reduce product quality and may cause yarn breakage. In this paper, the natural frequencies and mode shapes of a single loop balloon are calculated to predict resonance. The three dimensional nonlinear equations of motion are simplified via small steady state displacement (sag) and vibration assumptions. Axial vibration is assumed to propagate instantaneously or in a quasistatic manner. Galerkin’s method is used to calculate the mode shapes and natural frequencies of the linearized equations. Experimental measurements of the steady state balloon shape and the first two natural frequencies and mode shapes are compared with theoretical predictions.

Modal Analysis of the Cabinet of a Drum Washing Machine

2011 ◽  
Vol 199-200 ◽  
pp. 1126-1129
Author(s):  
Su Fang Fu ◽  
Han Gao ◽  
Jia Xi Du ◽  
Qiu Ju Zhang ◽  
Xue Ming Zhang ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Natural Frequencies ◽  
Element Model ◽  
Mode Shapes ◽  
Ansys Software ◽  
Washing Machine ◽  
Element Analysis ◽  
The Finite Element Model ◽  
Good Agreement

In this paper, the finite element model for the cabinet of a drum washing machine and the model for testing vibration of the cabinet were developed in ANSYS software and PULSE™, respectively. A series of tests were conducted. The natural frequencies and mode shapes were obtained by finite element analysis and modal experiment, which revealed weak parts of the cabinet. Meanwhile, the computational modes were in good agreement with experimental ones and this could provide an available method by which it was convenient to improve the design of the cabinet.

Sign in / Sign up

Export Citation Format

Share Document