scholarly journals Optimisation of power generation cycles using saturated liquid expansion to maximise heat recovery

2016 ◽  
Vol 231 (1) ◽  
pp. 57-69 ◽  
Author(s):  
MG Read ◽  
IK Smith ◽  
N Stosic
Keyword(s):  
Power Generation ◽  
High Pressure ◽  
Heat Recovery ◽  
Volume Ratio ◽  
Low Pressure ◽  
Working Fluid ◽  
Two Stage ◽  
Low Pressure Turbine ◽  
Screw Machine ◽  
Temperature Heat

The use of two-phase screw expanders in power generation cycles can achieve an increase in the utilisation of available energy from a low-temperature heat source when compared with more conventional single-phase turbines. The efficiency of screw expander machines is sensitive to expansion volume ratio, which, for given inlet and discharge pressures, increases as the expander inlet vapour dryness fraction decreases. For single-stage screw machines with low inlet dryness, this can lead to underexpansion of the working fluid and low isentropic efficiency. The cycle efficiency can potentially be improved by using a two-stage expander, consisting of a machine for low-pressure expansion and a smaller high-pressure machine connected in series. By expanding the working fluid over two stages, the built-in volume ratios of the two machines can be selected to provide a better match with the overall expansion process, thereby increasing the efficiency. The mass flow rate though both stages must be matched, and the compromise between increasing efficiency and maximising power output must also be considered. This study is based on the use of a rigorous thermodynamic screw machine model to compare the performance of single- and two-stage expanders. The model allows optimisation of the required intermediate pressure in the two-stage expander, along with the built-in volume ratio of both screw machine stages. The results allow specification of a two-stage machine, using either two screw machines or a combination of high-pressure screw and low-pressure turbine, in order to achieve maximum efficiency for a particular power output. For the low-temperature heat recovery application considered in this paper, the trilateral flash cycle using a two-stage expander and the Smith cycle using a high-pressure screw and low-pressure turbine are both predicted to achieve a similar overall conversion efficiency to that of a conventional saturated vapour organic Rankine cycle.

scholarly journals Investigations of the synergy of Composite Cycle and intercooled recuperation

2018 ◽  
Vol 122 (1252) ◽  
pp. 869-888 ◽  
Author(s):  
Sascha Kaiser ◽  
Markus Nickl ◽  
Christina Salpingidou ◽  
Zinon Vlahostergios ◽  
Stefan Donnerhack ◽  
...  
Keyword(s):  
High Pressure ◽  
Heat Recovery ◽  
Waste Heat Recovery ◽  
Waste Heat ◽  
Low Pressure ◽  
Low Pressure Turbine ◽  
The Core ◽  
Fuel Burn ◽  
Piston System ◽  
Temperature Levels

ABSTRACTThe synergistic combination of two promising engine architectures for future aero engines is presented. The first is the Composite Cycle Engine, which introduces a piston system in the high pressure part of the core engine, to utilise closed volume combustion and high temperature capability due to instationary operation. The second is the Intercooled Recuperated engine that employs recuperators to utilise waste heat from the core engine exhaust and intercooler to improve temperature levels for recuperation and to reduce compression work. Combinations of both architectures are presented and investigated for improvement potential with respect to specific fuel consumption, engine weight and fuel burn against a turbofan. The Composite Cycle alone provides a 15.6% fuel burn reduction against a turbofan. Options for adding intercooler were screened, and a benefit of up to 1.9% fuel burn could be shown for installation in front of a piston system through a significant, efficiency-neutral weight decrease. Waste heat can be utilised by means of classic recuperation to the entire core mass flow before the combustor, or alternatively on the turbine cooling bleed or a piston engine bypass flow that is mixed again with the main flow before the combustor. As further permutation, waste heat can be recovered either after the low pressure turbine – with or without sequential combustion – or between the high pressure and low pressure turbine. Waste heat recovery after the low pressure turbine was found to be not easily feasible or tied to high fuel burn penalties due to unfavourable temperature levels, even when using sequential combustion or intercooling. Feasible temperature levels could be obtained with inter-turbine waste heat recovery but always resulted in at least 0.3% higher fuel burn compared to the non-recuperated baseline under the given assumptions. Consequently, only the application of an intercooler appears to provide a considerable benefit for the examined thermodynamic conditions in the low fidelity analyses of various engine architecture combinations with the specific heat exchanger design. Since the obtained drawbacks of some waste heat utilisation concepts are small, innovative waste heat management concepts coupled with the further extension of the design space and the inclusion of higher fidelity models may achieve a benefit and motivate future investigations.

Influence of Hot Streak Temperature Ratio on Low Pressure Stage of a Vaneless Counter-Rotating Turbine

2007 ◽  
Author(s):  
Qingjun Zhao ◽  
Fei Tang ◽  
Huishe Wang ◽  
Jianyi Du ◽  
Xiaolu Zhao ◽  
...  
Keyword(s):  
Shock Wave ◽  
High Pressure ◽  
Secondary Flow ◽  
Low Pressure ◽  
Turbine Rotor ◽  
Temperature Ratio ◽  
High Pressure Turbine ◽  
Pressure Stage ◽  
Low Pressure Turbine ◽  
Hot Streak

In order to explore the influence of hot streak temperature ratio on low pressure stage of a Vaneless Counter-Rotating Turbine, three-dimensional multiblade row unsteady Navier-Stokes simulations have been performed. The predicted results show that hot streaks are not mixed out by the time they reach the exit of the high pressure turbine rotor. The separation of colder and hotter fluids is observed at the inlet of the low pressure turbine rotor. After making interactions with the inner-extending shock wave and outer-extending shock wave in the high pressure turbine rotor, the hotter fluid migrates towards the pressure surface of the low pressure turbine rotor, and the most of colder fluid migrates to the suction surface of the low pressure turbine rotor. The migrating characteristics of the hot streaks are predominated by the secondary flow in the low pressure turbine rotor. The effect of buoyancy on the hotter fluid is very weak in the low pressure turbine rotor. The results also indicate that the secondary flow intensifies in the low pressure turbine rotor when the hot streak temperature ratio is increased. The effects of the hot streak temperature ratio on the relative Mach number and the relative flow angle at the inlet of the low pressure turbine rotor are very remarkable. The isentropic efficiency of the Vaneless Counter-Rotating Turbine decreases as the hot streak temperature ratio is increased.

Design of an Intermediate Turbine Duct Downstream of a High Pressure Turbine

2016 ◽  
Author(s):  
Chaoshan Hou ◽  
Hu Wu
Keyword(s):  
High Pressure ◽  
Three Dimensional ◽  
Low Pressure ◽  
Aerodynamic Load ◽  
Duct Flow ◽  
Original Design ◽  
High Pressure Turbine ◽  
Intermediate Turbine Duct ◽  
Low Pressure Turbine ◽  
Inlet Conditions

The flow leaving the high pressure turbine should be guided to the low pressure turbine by an annular diffuser, which is called as the intermediate turbine duct. Flow separation, which would result in secondary flow and cause great flow loss, is easily induced by the negative pressure gradient inside the duct. And such non-uniform flow field would also affect the inlet conditions of the low pressure turbine, resulting in efficiency reduction of low pressure turbine. Highly efficient intermediate turbine duct cannot be designed without considering the effects of the rotating row of the high pressure turbine. A typical turbine model is simulated by commercial computational fluid dynamics method. This model is used to validate the accuracy and reliability of the selected numerical method by comparing the numerical results with the experimental results. An intermediate turbine duct with eight struts has been designed initially downstream of an existing high pressure turbine. On the basis of the original design, the main purpose of this paper is to reduce the net aerodynamic load on the strut surface and thus minimize the overall duct loss. Full three-dimensional inverse method is applied to the redesign of the struts. It is revealed that the duct with new struts after inverse design has an improved performance as compared with the original one.

scholarly journals Optimization of Powerful Two-stage Screw Centrifugal Pump

2018 ◽  
Vol 220 ◽  
pp. 03009 ◽  
Author(s):  
Oleg Baturin ◽  
Grigorii Popov ◽  
Daria Kolmakova ◽  
Vasilii Zubanov ◽  
Julia Novikova ◽  
...  
Keyword(s):  
High Pressure ◽  
Centrifugal Pump ◽  
Mathematical Optimization ◽  
Pressure Head ◽  
Low Pressure ◽  
Calculation Model ◽  
Pump Efficiency ◽  
Rotor Speed ◽  
Two Stage ◽  
Optimization Parameters

The article presents a refining method for a two-stage screw centrifugal pump by the joint usage of mathematical optimization software IOSO, meshing complex NUMECA and CFD software ANSYS CFX. The pump main parameters: high-pressure stage rotor speed was 13300 rpm; low-pressure rotor speed was 3617 rpm by gearbox; inlet total pressure was 0.4 MPa; outlet mass flow was 132.6 kg/s at the nominal mode. This article describes the process of simplifying the calculation model for the optimization. The parameters of camber lines of the low-pressure impeller, transition duct, and high-pressure impeller blades for two sections (hub and shroud) were chosen as optimization parameters. The blades of low-pressure impeller, transition duct and high-pressure impeller have changed during optimization. The optimization goal was the increase of the pump efficiency with preservation or slight increase in the pressure head. The efficiency was increased by 3%.

The Unsteady Flow Field of a Purged High Pressure Turbine Based on Mode Detection

2017 ◽  
Author(s):  
S. Zerobin ◽  
S. Bauinger ◽  
A. Marn ◽  
A. Peters ◽  
F. Heitmeir ◽  
...  
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Unsteady Flow ◽  
Flow Behavior ◽  
Low Pressure ◽  
Pressure Probe ◽  
Special Focus ◽  
High Pressure Turbine ◽  
Low Pressure Turbine ◽  
Mode Detection

This paper presents an experimental study of the unsteady flow field downstream of a high pressure turbine with ejected purge flows, with a special focus on a flow field discussion using the mode detection approach according to the theory of Tyler and Sofrin. Measurements were carried out in a product-representative one and a half stage turbine test setup, which consists of a high-pressure turbine stage followed by an intermediate turbine center frame and a low-pressure turbine vane row. Four independent purge mass flows were injected through the forward and aft cavities of the unshrouded high-pressure turbine rotor. A fast-response pressure probe was used to acquire time-resolved data at the turbine center frame duct inlet and exit. The interactions between the stator, rotor, and turbine center frame duct are identified as spinning modes, propagating in azimuthal direction. Time-space diagrams illustrate the amplitude variation of the detected modes along the span. The composition of the unsteadiness and its major contributors are of interest to determine the role of unsteadiness in the turbine center frame duct loss generation mechanisms and to avoid high levels of blade vibrations in the low-pressure turbine which can in turn result in increased acoustic emissions. This work offers new insight into the unsteady flow behavior downstream of a purged high-pressure turbine and its propagation through an engine-representative turbine center frame duct configuration.

Combined Cycle for Power Generation and Refrigeration Using Low Temperature Heat Sources

2014 ◽  
Vol 3 (3) ◽  
pp. 34-56 ◽  
Author(s):  
Vijay Chauhan ◽  
P. Anil Kishan ◽  
Sateesh Gedupudi
Keyword(s):  
Power Generation ◽  
Low Temperature ◽  
Combined Cycle ◽  
Working Fluid ◽  
Heat Sources ◽  
Ambient Temperatures ◽  
Temperature Heat ◽  
Good Potential ◽  
Output Ratio ◽  
Operation Results

A combined refrigeration and power cycle, which uses ammonia-water as the working fluid, is proposed by combining Rankine and vapour absorption cycles with an advantage of varying refrigeration capacity to power output ratio. The study investigates the usage of low temperature heat sources for the cycle operation. Results of parametric analysis are presented, which show the scope for optimization. Results of thermodynamic optimization of the cycle for second law efficiency performed using genetic algorithm for different ambient temperatures are also presented. The cycle shows good potential for obtaining refrigeration and power generation.

Experimental Investigation of Vane Clocking in a One and 1/2 Stage High Pressure Turbine

2004 ◽  
Author(s):  
Charles W. Haldeman ◽  
Michael G. Dunn ◽  
John W. Barter ◽  
Brian R. Green ◽  
Robert F. Bergholz
Keyword(s):  
High Pressure ◽  
Low Pressure ◽  
Test Facility ◽  
Maximum Efficiency ◽  
High Pressure Turbine ◽  
Data Set ◽  
Time Resolved ◽  
Low Pressure Turbine ◽  
Turbine Vane ◽  
Vane Clocking

Aerodynamic measurements were acquired on a modern single-stage, transonic, high-pressure turbine with the adjacent low-pressure turbine vane row (a typical civilian one and one-half stage turbine rig) to observe the effects of low-pressure turbine vane clocking on overall turbine performance. The turbine rig (loosely referred to in this paper as the stage) was operated at design corrected conditions using the Ohio State University Gas Turbine Laboratory Turbine Test Facility (TTF). The research program utilized uncooled hardware in which all three airfoils were heavily instrumented at multiple spans to develop a full clocking dataset. The low-pressure turbine vane row (LPTV) was clocked relative to the high-pressure turbine vane row (HPTV). Various methods were used to evaluate the influence of clocking on the aeroperformance (efficiency) and the aerodynamics (pressure loading) of the LPTV, including time-resolved and time-averaged measurements. A change in overall efficiency of approximately 2–3% due to clocking effects is demonstrated and could be observed using a variety of independent methods. Maximum efficiency is obtained when the time-average surface pressures are highest on the LPTV and the time-resolved surface pressure (both in the time domain and frequency domain) show the least amount of variation. The overall effect is obtained by integrating over the entire airfoil, as the three-dimensional effects on the LPTV surface are significant. This experimental data set validates several computational research efforts that suggested wake migration is the primary reason for the perceived effectiveness of vane clocking. The suggestion that wake migration is the dominate mechanism in generating the clocking effect is also consistent with anecdotal evidence that fully cooled engine rigs do not see a great deal of clocking effect. This is consistent since the additional disturbances induced by the cooling flows and/or the combustor make it extremely difficult to find an alignment for the LPTV given the strong 3D nature of modern high-pressure turbine flows.

Application of a miniaturized solid state electrolyte sensor for tracer gas measurements in a two-stage low pressure turbine

2017 ◽  
Vol 82 ◽  
pp. 367-374 ◽  
Author(s):  
Marcel Günter ◽  
Frank Hammer ◽  
Christian Koch ◽  
Klaus Kuhn ◽  
Martin G. Rose ◽  
...  
Keyword(s):  
Solid State ◽  
Low Pressure ◽  
Tracer Gas ◽  
Two Stage ◽  
Solid State Electrolyte ◽  
Low Pressure Turbine ◽  
Gas Measurements

Numerical Investigation of the Effect of Tip Leakage Flow on an Aggressive S-Shaped Intermediate Turbine Duct

2009 ◽  
Author(s):  
W. Sanz ◽  
M. Kelterer ◽  
R. Pecnik ◽  
A. Marn ◽  
E. Go¨ttlich
Keyword(s):  
High Pressure ◽  
Low Pressure ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
High Pressure Turbine ◽  
Tip Leakage ◽  
Intermediate Turbine Duct ◽  
Low Pressure Turbine ◽  
High Diffusion ◽  
Gap Height

The demand of a further increased bypass ratio of aero engines will lead to low pressure turbines with larger diameters which rotate at lower speed. Therefore, it is necessary to guide the flow leaving the high pressure turbine to the low pressure turbine at a larger diameter without any loss generating separation or flow disturbances. Due to costs and weight this intermediate turbine duct has to be as short as possible. This leads to an aggressive (high diffusion) S-shaped duct geometry. In order to investigate the influence of the blade tip gap height of a preceding rotor on such a high-diffusion duct flow a detailed measurement campaign in the Transonic Test Turbine Facility at Graz University of Technology has been performed. A high diffusion intermediate duct is arranged downstream a high-pressure turbine stage providing an exit Mach number of about 0.6 and a swirl angle of −15 degrees (counter swirl). A low-pressure vane row is located at the end of the duct and represents the counter rotating low pressure turbine at larger diameter. At the ASME 2007, results of these investigations were presented for two different tip gap heights of 1.5% span (0.8 mm) and 2.4% span (1.3 mm). In order to better understand the flow phenomena observed in the intermediate duct a detailed numerical study is conducted. The unsteady flow through the whole configuration is simulated for both gap heights as well as for a rotor with zero gap height. The unsteady data are compared at the stage exit and inside the duct to study the flow physics. The calculation of the zero gap height configuration allows to determine the influence of the tip leakage flow of the preceding rotor on the intermediate turbine duct. It turns out that for this aggressive duct the tip leakage flow has a very positive effect on the pressure recovery.

Sign in / Sign up

Export Citation Format

Share Document