Effect of heat input on mechanical and microstructural properties of Inconel 625 depositions processed in wire arc additive manufacturing

2021 ◽  
pp. 095440892110047
Author(s):  
DT Sarathchandra ◽  
MJ Davidson
Keyword(s):  
Heat Input ◽  
Elevated Temperatures ◽  
Microstructural Characterization ◽  
Deposition Process ◽  
Columnar Structure ◽  
Inconel 625 ◽  
Cold Metal Transfer ◽  
Electron Microscopes ◽  
Cold Metal ◽  
Wire Arc Additive Manufacturing

Inconel 625 alloy resists corrosion, fatigue and wear at elevated temperatures and hence they are used in aerospace, chemical, petrochemical, marine, and other high-temperature applications. In the present study, single beads of Inconel 625 were deposited using the cold metal transfer (CMT) based wire arc deposition process. Seven heat input conditions were used to study the microstructure and mechanical characteristics. Microstructural characterization was done with optical and scanning electron microscopes while microhardness was measured using the Vickers microhardness testing method. It has been observed that the microstructure of the deposited beads consists of a columnar structure with primary dendrites. Also, intermetallic elements like Niobium (Nb), Molybdenum (Mo), and Laves were formed. It was also observed that the percentage of Nb and Mo increases with heat input. The microhardness increases with an increase in heat input and the maximum hardness was found to be 234.7 HV.

scholarly journals On the Effect of Heat Input and Interpass Temperature on the Performance of Inconel 625 Alloy Deposited Using Wire Arc Additive Manufacturing–Cold Metal Transfer Process

Metals ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 46
Author(s):  
Chengxun Zhang ◽  
Zhijun Qiu ◽  
Hanliang Zhu ◽  
Zhiyang Wang ◽  
Ondrej Muránsky ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Heat Input ◽  
Inconel 625 ◽  
Heat Accumulation ◽  
Cold Metal Transfer ◽  
Inconel 625 Alloy ◽  
Cold Metal ◽  
Wire Arc Additive Manufacturing ◽  
Interpass Temperature

Relatively high heat input and heat accumulation are treated as critical challenges to affect the qualities and performances of components fabricated by wire arc additive manufacturing (WAAM). In this study, various heat inputs, namely 276, 552 and 828 J/mm, were performed to fabricate three thin-wall Inconel 625 structures by cold metal transfer (CMT)-based WAAM, respectively, and active interpass cooling was conducted to limit heat accumulation. The macrostructure, microstructure and mechanical properties of the produced components by CMT were investigated. It was found that the increased heat input can deteriorate surface roughness, and the size of dendrite arm spacing increases with increasing heat input, thus leading to the deterioration of mechanical properties. Lower heat input and application of active interpass cooling can be an effective method to refine microstructure and reduce anisotropy. This study enhances the understanding of interpass temperature control and the effectiveness of heat inputs for Inconel 625 alloy by WAAM. It also provides a valuable in situ process for microstructure and mechanical properties’ refinement of WAAM-fabricated alloys and the control of heat accumulation for the fabrication of large-sized structures for future practical applications.

Control of humping phenomenon and analyzing mechanical properties of Al–Si wire-arc additive manufacturing fabricated samples using cold metal transfer process

2021 ◽  
pp. 095440622199840
Author(s):  
Yashwant Koli ◽  
N Yuvaraj ◽  
Aravindan Sivanandam ◽  
Vipin
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Heat Input ◽  
Large Scale ◽  
High Deposition Rate ◽  
Bead Geometry ◽  
Layer By Layer ◽  
Cold Metal Transfer ◽  
Geometrical Shapes ◽  
Wire Arc Additive Manufacturing

Nowadays, rapid prototyping is an emerging trend that is followed by industries and auto sector on a large scale which produces intricate geometrical shapes for industrial applications. The wire arc additive manufacturing (WAAM) technique produces large scale industrial products which having intricate geometrical shapes, which is fabricated by layer by layer metal deposition. In this paper, the CMT technique is used to fabricate single-walled WAAM samples. CMT has a high deposition rate, lower thermal heat input and high cladding efficiency characteristics. Humping is a common defect encountered in the WAAM method which not only deteriorates the bead geometry/weld aesthetics but also limits the positional capability in the process. Humping defect also plays a vital role in the reduction of hardness and tensile strength of the fabricated WAAM sample. The humping defect can be controlled by using low heat input parameters which ultimately improves the mechanical properties of WAAM samples. Two types of path planning directions namely uni-directional and bi-directional are adopted in this paper. Results show that the optimum WAAM sample can be achieved by adopting a bi-directional strategy and operating with lower heat input process parameters. This avoids both material wastage and humping defect of the fabricated samples.

scholarly journals Effect of Filler Metal Type on Microstructure and Mechanical Properties of Fabricated NiAl Bronze Alloy Using Wire Arc Additive Manufacturing System

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 513
Author(s):  
Jae Won Kim ◽  
Jae-Deuk Kim ◽  
Jooyoung Cheon ◽  
Changwook Ji
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Additive Manufacturing ◽  
Filler Metal ◽  
Gas Metal Arc Welding ◽  
Metal Wire ◽  
Cold Metal Transfer ◽  
Metal Type ◽  
Cold Metal ◽  
Wire Arc Additive Manufacturing

This study observed the effect of filler metal type on mechanical properties of NAB (NiAl-bronze) material fabricated using wire arc additive manufacturing (WAAM) technology. The selection of filler metal type is must consider the field condition, mechanical properties required by customers, and economics. This study analyzed the bead shape for representative two kind of filler metal types use to maintenance and fabricated a two-dimensional bulk NAB material. The cold metal transfer (CMT) mode of gas metal arc welding (GMAW) was used. For a comparison of mechanical properties, the study obtained three specimens per welding direction from the fabricated bulk NAB material. In the tensile test, the NAB material deposited using filler metal wire A showed higher tensile strength and lower elongation (approx. +71 MPa yield strength, +107.1 MPa ultimate tensile strength, −12.4% elongation) than that deposited with filler metal wire B. The reason is that, a mixture of tangled fine α platelets and dense lamellar eutectoid α + κIII structure with β´ phases was observed in the wall made with filler metal wire A. On the other hand, the wall made with filler metal wire B was dominated by coarse α phases and lamellar eutectoid α + κIII structure in between.

Cold Metal Transfer Spot Joining of AA6061-T6 to Galvanized DP590 Under Different Modes

2015 ◽  
Vol 137 (5) ◽  
Author(s):  
HaiYang Lei ◽  
YongBing Li ◽  
Blair E. Carlson ◽  
ZhongQin Lin
Keyword(s):  
Heat Input ◽  
Mechanical Performance ◽  
Welding Process ◽  
High Strength ◽  
Metal Transfer ◽  
Cold Metal Transfer ◽  
Spot Joining ◽  
Predrilled Hole ◽  
Joint Quality ◽  
Cold Metal

In order to meet the upcoming regulations on greenhouse gas emissions, aluminum use in the automotive industry is increasing. However, this increase is now seen as part of a multimaterial strategy. Consequently, dissimilar material joints are a reality, which poses significant challenges to conventional fusion joining processes. To address this issue, cold metal transfer (CMT) spot welding process was developed in the current study to join aluminum alloy AA6061-T6 as the top sheet to hot dip galvanized (HDG) advanced high strength steel (AHSS) DP590 as the bottom sheet. Three different welding modes, i.e., direct welding (DW) mode, plug welding (PW) mode, and edge plug welding (EPW) mode were proposed and investigated. The DW mode, having no predrilled hole in the aluminum top sheet, required concentrated heat input to melt through the Al top sheet and resulted in a severe tearing fracture, shrinkage voids, and uneven intermetallic compounds (IMC) layer along the faying surface, leading to poor joint properties. Welding with the predrilled hole, PW mode, required significantly less heat input and led to greatly reduced, albeit uneven, IMC layer thickness. However, it was found that the EPW mode could homogenize the welding heat input into the hole and thus produce the most stable welding process and best joint quality. This led to joints having an excellent joint morphology characterized by the thinnest IMC layer and consequently, best mechanical performance among the three modes.

Effect of the CMT advanced process combined with an active cooling technique on macro and microstructural aspects of aluminum WAAM

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Felipe Ribeiro Teixeira ◽  
Fernando Matos Scotti ◽  
Ruham Pablo Reis ◽  
Américo Scotti
Keyword(s):  
Electrical Signal ◽  
Management Technique ◽  
Marginal Effect ◽  
Thin Wall ◽  
Cold Metal Transfer ◽  
Content Type ◽  
Active Cooling ◽  
Cold Metal ◽  
Wire Arc Additive Manufacturing ◽  
Cooling Technique

Purpose This paper aims to assess the combined effect of the Cold Metal Transfer (CMT) advanced process and of a thermal management technique (near immersion active cooling [NIAC]) on the macro and microstructure of Al wall-like preforms built by wire arc additive manufacturing (WAAM). As specific objective, it sought to provide information on the effects of the electrode-positive/electrode-negative (EP/EN) parameter in the CMT advanced process fundamental characteristics. Design/methodology/approach Initially, bead-on-plate deposits were produced with different EP/EN ratios, still keeping the same deposition rate, and the outcomes on the electrical signal traces and bead formation were analyzed. In a second stage, the EP/EN parameter and the layer edge to water distance (LEWD) parameter from the NIAC technique were systematically varied and the resultant macro and microstructures compared with those formed by applying natural cooling. Findings Constraints of EP/EN setting range were uncovered and discussed. The use of the NIAC technique favors the formation of finer grains. For a given EP/EN value, a variation in the NIAC intensity (LEWD value) showed marginal effect on grain size. When the EP/EN parameter effect is isolated, i.e. for a given LEWD setting, it was observed that an increase in the EP/EN level favors coarser grains. Originality/value Both the EP/EN parameter and the use of an active cooling technique (NIAC) might be used, even in combination, as effective tools for achieving proper macro and microstructure in WAAM of thin wall builds.

Microstructure and mechanical properties of cold metal transfer welded galvanized steel/magnesium alloy dissimilar joints

2019 ◽  
Vol 34 (01n03) ◽  
pp. 2040060
Author(s):  
Chao Zhang ◽  
Mingfang Wu ◽  
Yuxin Wang ◽  
Juan Pu
Keyword(s):  
Magnesium Alloy ◽  
Heat Input ◽  
Interface Layer ◽  
Metal Transfer ◽  
Galvanized Steel ◽  
Cold Metal Transfer ◽  
Welding Joint ◽  
Welding Heat Input ◽  
Weld Appearance ◽  
Cold Metal

The joining of magnesium alloy to galvanized steel was realized by cold metal transfer method with AZ31 magnesium alloy welding wire. Weld appearance, microstructure and tensile properties of Mg–steel joints under various welding parameters were investigated with different welding heat inputs. The results showed that magnesium alloy-steel brazed joints had good weld appearance. When the welding heat input was 141 J/mm, Zn elements were enriched in the Zn-rich zone (ZRZ), and the interface layer was composed of a large portion of Mg–Zn phases and minor Mg–Al phases. With the increase of welding heat input, Zn elements in the ZRZ gradually decreased, Fe/Al phase appeared in the interface layer, and the strength of welding joint increased. When the welding heat input was 159 J/mm, the tensile strength of welding joint reached the maximum value of 198 MPa. However, when the welding input was increased to 181 J/mm, Zn element in the ZRZ was burnt and volatilized seriously, resulting in poor wetting and spreading properties of liquid phase at the interface zone of the steel.

Cold Metal Transfer Welding of AA6061 to AA7075: Mechanical Properties and Corrosion

2019 ◽  
Vol 141 (3) ◽  
Author(s):  
Nilay Çömez ◽  
Hülya Durmuş
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Heat Input ◽  
Dissimilar Materials ◽  
Metal Transfer ◽  
Welding Parameters ◽  
Cold Metal Transfer ◽  
Cmt Welding ◽  
Mechanical Properties And Corrosion ◽  
Cold Metal

Cold metal transfer (CMT) welding provides many advantages for welding of dissimilar materials and thin sheets with its superior heat input control mechanism. In this study, AA6061 and AA7075 aluminum alloys were joined with CMT welding. The effect of welding parameters on hardness, tensile strength, and corrosion rate was investigated. The Tafel extrapolation method was carried out to determine the corrosion rates of AA6061 and AA7075 base metals and AA6061–AA7075 joints. Increasing heat input was found to be detrimental for both mechanical properties and corrosion resistance. The outcomes showed that CMT welding produces adequate joints of AA6061–AA7075 in terms of mechanical properties and corrosion resistance, favorably with welding parameters that provide low heat input.

Sign in / Sign up

Export Citation Format

Share Document