Parametric study on pressure-based packed bed adsorption system for air dehumidification

2021 ◽  
pp. 095440892110073
Author(s):  
V Sureshkannan ◽  
TV Arjunan ◽  
D Seenivasan ◽  
SP Anbuudayasankar ◽  
M Arulraj
Keyword(s):  
Genetic Algorithm ◽  
Taguchi Method ◽  
Flow Rate ◽  
Uptake Rate ◽  
Air Flow ◽  
Packed Bed ◽  
Air Pressure ◽  
Dew Point ◽  
Adsorption System ◽  
Air Flow Rate

Compressed air free from traces of water vapour is vital in many applications in an industrial sector. This study focuses on parametric optimization of a pressure-based packed bed adsorption system for air dehumidification through the Taguchi method and Genetic Algorithm. The effect of operational parameters, namely absolute feed air pressure, feed air linear velocity, and purge air flow rate percent on adsorption uptake rate of molecular sieve 13X-water pair, are studied based on L25 orthogonal array. From the analysis of variance, it has been found that absolute feed air pressure and purge air flow rate percent were the parameters making significant improvement in the adsorption uptake rate. A correlation representing the process was developed using regression analysis. The optimum adsorption conditions were obtained through the Taguchi method and genetic algorithm and verified through the confirmation experiments. This system can be recommended for the industrial and domestic applications that require product air with the dew point temperature below 0°C.

Oral Air Pressure and Nasal Air Flow Rate on Levator Veli Palatini Muscle Activity in Patients Wearing a Speech Appliance

1995 ◽  
Vol 32 (5) ◽  
pp. 382-389 ◽  
Author(s):  
Takashi Tachimura ◽  
Hisanaga Hara ◽  
Takeshi Wada
Keyword(s):  
Flow Rate ◽  
Muscle Activity ◽  
Neural Control ◽  
Air Flow ◽  
Air Pressure ◽  
Electromyographic Activity ◽  
Air Flow Rate ◽  
Circular Area ◽  
Pharyngeal Bulb ◽  
Levator Veli Palatini

This study was designed to determine if levator veli palatini muscle activity can be elicited by simultaneous changes in oral air pressure and nasal air flow when a speech appliance is in place. The speech appliances routinely worn by 15 subjects were each modified experimentally by drilling a hole in the vertical center of the pharyngeal bulb. The air flow rate into the nasal cavity through the opening in the bulb was altered by changing the circular area of the opening in the bulb from the occluded condition (Condition I), to circular area of 12.6 mm2 (4 mm in diameter; Condition II), and then to 38.5 mm2 (7 mm in diameter; Condition III). Electromyographic activity was measured from the levator veli palatini muscle with changes in nasal air flow rate and oral air pressure. Levator veli palatini muscle activity was correlated with changes in nasal air flow and oral air pressure. Increases in levator veli palatini muscle activity were associated with increases in nasal air flow rate compared to oral air pressure changes. The results indicated that aerodynamic variables of nasal air flow and oral air pressure might be involved in the neural control of speech production in individuals wearing a speech appliance, even if the subjects exhibit velopharyngeal incompetence without using a speech appliance. Also, the stimulating effect of bulb reduction therapy on velopharyngeal function might be achieved through the change in aerodynamic variables in association with the bulb reduction.

Performance Analysis of Eductor Used for Main Control Room Ventilating in Nuclear Power Plant

2017 ◽  
Author(s):  
Xin Yu ◽  
Yuqing Lin ◽  
Yan Zhang
Keyword(s):  
Flow Rate ◽  
Nuclear Power ◽  
Air Flow ◽  
Test System ◽  
Air Pressure ◽  
Air Flow Rate ◽  
Control Room ◽  
Entrainment Ratio ◽  
Pressurized Water ◽  
Set Up

This paper proposes the experimental research for the performance of the air eductor used in main control room (MCR). The air eductor is used for emergency ventilating in advanced passive pressurized water reactor in accident. The compress air is supplied to the eductor as a power source and the indoor air is suctioned to the eductor. The performance of the eductor is related to the habitability of MCR. The entrainment ratio and the air pressure of discharge side are the main concerned performance. The entrainment ratio is a value that resulted from the compress air flow rate divided by the suction air flow rate. A test system was set up to test the performance of eductor. The experimental results show that the entrainment ratio of rectangle nozzle with compress air pressure 0.76MPa, 0.80MPa and 0.83MPa were 15.02, 15.04 and 15.06, respectively.

Plug Flow of Coarse Particles in a Horizontal Pipe

1982 ◽  
Vol 104 (2) ◽  
pp. 198-206 ◽  
Author(s):  
Y. Tsuji ◽  
Y. Morikawa
Keyword(s):  
Pressure Drop ◽  
Flow Rate ◽  
Air Flow ◽  
Plug Flow ◽  
Packed Bed ◽  
Coarse Particles ◽  
Air Flow Rate ◽  
Horizontal Pipe ◽  
Main Pipe ◽  
Secondary Air

Plug flow of coarse particles was investigated experimentally in a horizontal pipe, in which a sub-pipe for secondary air injection was installed. Measurements were made about the plug motion, pressure drop, and transportation properties, and the roles of the main and sub-pipe air flow were clarified. The main air flow increases the number of plugs, while the sub-pipe air flow increases the plug velocity. The higher the main pipe air flow rate, the more regular the motion. The height of a stationary layer of deposited particles, which is built on the bottom of the main pipe, decreases with increasing the sub-pipe air flow rate. The pressure drop in the moving plug is quantitatively much smaller than that in the stationary packed bed of same particles.

AIR FLOW SENSOR

2021 ◽  
Author(s):  
Андрей Евгеньевич Скугаров ◽  
Светлана Анатольевна Микаева
Keyword(s):  
Flow Rate ◽  
Air Flow ◽  
Air Pressure ◽  
Flow Sensor ◽  
Pitot Tube ◽  
Sensor Design ◽  
Air Flow Rate ◽  
Fixed Plate

В статье описаны датчики массового расхода воздуха. Авторы приводят типы различных конструкций, принцип действия и способы определения расхода воздуха. В основе конструкции датчика лежит трубка Пито и закреплённая пластина, которая деформируется под давлением воздуха. The article describes the sensors of mass air flow.The authors give the types of various structures, the principle of operation and methods for determining the air flow rate. The sensor design is based on a Pitot tube and a fixed plate that deforms under air pressure.

scholarly journals Performance Investigation of MQL Parameters Using Nano Cutting Fluids in Hard Milling

Fluids ◽  
2021 ◽  
Vol 6 (7) ◽  
pp. 248
Author(s):  
Tran Minh Duc ◽  
Tran The Long ◽  
Ngo Minh Tuan
Keyword(s):  
Flow Rate ◽  
Cutting Forces ◽  
Air Flow ◽  
Cutting Temperature ◽  
Air Pressure ◽  
Cutting Fluid ◽  
Al2o3 Nanoparticles ◽  
Air Flow Rate ◽  
Hard Milling ◽  
Lubrication Performance

Machining difficult-to-cut materials is one of the increasingly concerned issues in the metalworking industry. Low machinability and high cutting temperature generated from the contact zone are the main obstacles that need to be solved in order to improve economic and technical efficiency but still have to ensure environmental friendliness. The application of MQL method using nano cutting fluid is one of the suggested solutions to improve the cooling and lubricating performance of pure-MQL for machining difficult-to-cut materials. The main objective of this paper is to investigate the effects of nanofluid MQL (NFMQL) parameters including the fluid type, type of nanoparticles, air pressure and air flow rate on cutting forces and surface roughness in hard milling of 60Si2Mn hardened steel (50–52 HRC). Analysis of variance (ANOVA) was implemented to study the effects of investigated variables on hard machining performance. The most outstanding finding is that the main effects of the input variables and their interaction are deeply investigated to prove the better machinability and the superior cooling lubrication performance when machining under NFMQL condition. The experimental results indicate that the uses of smaller air pressure and higher air flow rate decrease the cutting forces and improve the surface quality. Al2O3 nanoparticles show the better results than MoS2 nanosheets. The applicability of soybean oil, a type of vegetable oil, is proven to be enlarged in hard milling by suspending nanoparticles, suitable for further studies in the field of sustainable manufacturing.

scholarly journals Lipase production by solid-state fermentation in fixed-bed bioreactors

2005 ◽  
Vol 48 (spe) ◽  
pp. 79-84 ◽  
Author(s):  
Elisa d'Avila Costa Cavalcanti ◽  
Melissa Limoeiro Estrada Gutarra ◽  
Denise Maria Guimarães Freire ◽  
Leda dos Reis Castilho ◽  
Geraldo Lippel Sant'Anna Júnior
Keyword(s):  
Solid State ◽  
Flow Rate ◽  
Solid State Fermentation ◽  
Air Flow ◽  
Fixed Bed ◽  
Packed Bed ◽  
Lipase Production ◽  
Statistical Experimental Design ◽  
Air Flow Rate ◽  
Penicillium Simplicissimum

In the present work, packed bed bioreactors were employed with the aim of increasing productivity and scaling up of lipase production using Penicillium simplicissimum in solid-state fermentation. The influence of temperature and air flow rate on enzyme production was evaluated employing statistical experimental design, and an empirical model was adjusted to the experimental data. It was shown that higher lipase activities could be achieved at lower temperatures and higher air flow rates. The maximum lipase activity (26.4 U/g) was obtained at the temperature of 27°C and air flow rate of 0.8 L/min.

Sign in / Sign up

Export Citation Format

Share Document