Effect of the end-wall vortex generator jets on the performance of a high subsonic compressor cascade

2018 ◽  
Vol 233 (3) ◽  
pp. 324-336
Author(s):  
Cong Chen ◽  
Huaping Liu ◽  
Fu Chen
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Numerical Study ◽  
Vortex Generator ◽  
Total Pressure Loss ◽  
Experimental Result ◽  
Compressor Cascade ◽  
Design Point ◽  
Vortex Generator Jets ◽  
End Wall

This paper presents a numerical and experimental result of the end-wall vortex generator jets for controlling corner separation and enhancing the aerodynamic performance in a high subsonic (Ma = 0.7) compressor cascade. The experiments were carried out on a compressor cascade at design point ( i = 0°) and off-design points ( i = −2°, 2°, and 4°). At design point, the total pressure loss coefficient could be reduced up to 12.1%.With the increase in the incidence, the control effect is enhanced first and then reduced. The maximum total pressure loss reduction is up to 14.6% when the incidence is 2°. The numerical study is further conducted to analyze the flow pattern and the vortex structure. The jet vortex is formed downstream of the jet hole using the vortex generator jets, the cross flow on the end wall is also suppressed.

Effect of End-Wall Vortex Generator Jet Parameters on Flow Control in High Subsonic Compressor Cascade

2018 ◽  
Author(s):  
Cong Chen ◽  
Jianyang Yu ◽  
Fu Chen
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Vortex Generator ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Control Effect ◽  
Pressure Loss Coefficient ◽  
Vortex Generator Jet ◽  
End Wall ◽  
Total Pressure Loss Coefficient

In order to explore the control mechanism of vortex generator jet, which is located in the passage (PVGJ), on the separation flow, the influence of the pitch angle, skew angle, locations and jet-to-inflow ratio are studied using numerical methods in a high subsonic compressor cascade. The changing of the flow pattern is also analyzed in detail. The results show that the control effect of the end-wall vortex generator jet located in the passage is better than the leading edge one and the aerodynamic performance is effectively improved. The maximum total pressure loss coefficient decreases by 12% and the static pressure coefficient increases by 5.2% while the jet-to-inflow ratio is only 0.3%. The control effect is sensitive to the change of jet parameters. When 0 deg < β < 80 deg, 20 deg < α < 50 deg,, x < 0.5B, y < 0.15t, the vortex generation jet could acquire an ideal control effect. As the jet mass increases, the total pressure loss coefficient gradually reduces. The VGJ prevent separation mainly by bringing high momentum fluid into the near wall region and by promoting momentum transport through turbulent mixing in previous studies. Both the LVGJ and PVGJ mainly take advantage of jet vortex to prevent the cross flow from interacting with the suction side boundary layer.

Secondary Flow Control Using Vortex Generator Jets

2004 ◽  
Vol 126 (4) ◽  
pp. 650-657 ◽  
Author(s):  
R. K. Sullerey ◽  
A. M. Pradeep
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Vortex Generator ◽  
Control Flow ◽  
Secondary Flows ◽  
Total Pressure Loss ◽  
Vortex Generators ◽  
Vortex Generator Jets ◽  
Inflow Conditions

In this paper, results are presented of an experimental investigation into the effectiveness of vortex generator jets in controlling secondary flows in two-dimensional S-duct diffusers. The experiments were performed in uniform and distorted inflow conditions and the performance evaluation of the diffuser was carried out in terms of static pressure recovery and quality of the exit flow. In the case with inflow distortion, tapered fin vortex generators were employed in addition to vortex generator jets to control flow separation that was detected on the wall with inflow distortion. Detailed measurements including total pressure, velocity distribution, surface static pressure, skin friction, and boundary layer measurements were taken at a Reynolds number of 7.8×105. These results are presented in terms of static pressure rise, distortion coefficient, and total pressure loss coefficient at the duct exit. For uniform inflow, the use of vortex generator jets resulted in more than a 30 percent decrease in total pressure loss and flow distortion coefficients. In combination with passive device (tapered fin vortex generators), the vortex generator jets reduce total pressure losses by about 25 percent for distorted inflow conditions. A potential application of this method may include control of secondary flows in turbo machinery.

Impact of a Combination of Micro-Vortex Generator and Boundary Layer Suction on Performance in a High-Load Compressor Cascade

2018 ◽  
Author(s):  
Shan Ma ◽  
Wuli Chu ◽  
Haoguang Zhang ◽  
Chuanle Liu
Keyword(s):  
Boundary Layer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Vortex Generator ◽  
Aerodynamic Performance ◽  
Total Pressure Loss ◽  
Control Methods ◽  
Compressor Cascade ◽  
Boundary Layer Suction ◽  
Micro Vortex Generator

The performance of a compressor cascade is considerably influenced by flow control methods. In this paper, the synergistic effects of combination between micro-vortex generators (MVG) and boundary layer suction (BLS) are discussed in a high-load compressor cascade. Seven cases, which are grouped by a kind of micro-vortex generator and boundary layer suction with three locations, are investigated to control secondary flow effects and enhance the aerodynamic performance of the compressor cascade. The MVG is mounted on the end-wall in front of the passage. The rectangle suction slot with three radial positions is installed on the blade suction surface near the trailing edge. The numerical results show that: at the design condition, the total pressure loss is effectively decreased as well as the static pressure coefficient increase when the combined MVG and SBL method (COM) is used, which is superior to MVG in an aerodynamic performance. At the stall condition, the induced vortex coming from MVG could mix the low-energy fluid and mainstream, which result in the reduced separation, and the total pressure loss decreased by 11.54% when the suction flow ratio is 1.5%. The total pressure loss decreases by 14.59% when the COM control methods are applied.

Vortex Control Over End Wall Flow in Compressor Cascades

1990 ◽  
Author(s):  
Yan-Ping Tang ◽  
Mao-Zhang Chen
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Control Techniques ◽  
Vortex Control ◽  
New Concepts ◽  
Wall Flow ◽  
Linear Compressor Cascade ◽  
End Wall

Three methods of vortex control over the end wall flow in compressor cascades have been investigated experimentally. The total pressure loss at the exit of a linear compressor cascade is reduced 6.5%, 10.5% and 26.5% respectively by these methods for different incidences over a range of moderate-high values. The physics of these methods has been discussed and some new concepts of vortex control techniques in compressor cascades have been proposed.

Optimization study on the influence of little blades’ spatial position on a compressor cascade performance

2021 ◽  
pp. 095441002110443
Author(s):  
Shan Ma ◽  
Xiaolin Sun
Keyword(s):  
Flow Field ◽  
Pressure Loss ◽  
Total Pressure ◽  
Spatial Position ◽  
Total Pressure Loss ◽  
Field Analysis ◽  
Stable Operation ◽  
Compressor Cascade ◽  
Optimal Position ◽  
End Wall

To reveal the importance of little blades’ spatial position to improve the cascade performance at different condition, the pitchwise and axial direction of the little blades on the end-wall are adopted as the optimization variables to complete a double-objective optimization. Meanwhile, the three-dimensional flow field characteristics of the cascade with and without little blades are analyzed comparatively. The study found that as the optimal solutions are obtained at the three bigger incidences (3°, 5°, and 7°), the optimal position is always close to the leading edge of blade and far away from the blade suction surface, and the more intuitive design suggestions are given in this article. Moreover, at the near design conditions (−1°, 0°, and 1°), little blades increase the total pressure loss and reduce the static pressure, which are considered unsuitable for improving the cascade performance. If the stable operation range are the main performance indicators, the optimization of the little blades’ spatial position should be completed at the near stall condition (7° incidence). If the conditions with mid-range incidences (2°< i <5°) are the main performance index, the parameter optimization of little blades should be achieved at 5°. Based on the further flow field analysis of the optimization results obtained at 3°, 5°, and 7° incidences (named Opt_Act3, Opt_Act5, and Opt_Act7), the induced vortices resist the effect of axial reverse pressure gradient and pass through the blade passage, which is the main reason for the total pressure loss reduction. Appropriate spatial position of little blades not only strengthens the capability to prevent the low-energy fluids accumulating in the corner region near the end-wall, but exhibits sufficient advantage to weaken the boundary layer.

Benefits of Nonaxisymmetric Endwall Contouring in a Compressor Cascade With a Tip Clearance

2015 ◽  
Vol 137 (5) ◽  
Author(s):  
Mahesh K. Varpe ◽  
A. M. Pradeep
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Three Dimensional ◽  
Axial Flow ◽  
Vortex Generator ◽  
Tip Clearance ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Pressure Loss Coefficient ◽  
Flow Compressor

This paper describes the design of a nonaxisymmetric hub contouring in a shroudless axial flow compressor cascade operating at near stall condition. Although an optimum tip clearance (TC) reduces the total pressure loss, further reduction in the loss was achieved using hub contouring. The design methodology presented here combines an evolutionary principle with a three-dimensional (3D) computational fluid dynamics (CFD) flow solver to generate different geometric profiles of the hub systematically. The resulting configurations were preprocessed by GAMBIT© and subsequently analyzed computationally using ANSYSFluent©. The total pressure loss coefficient was used as a single objective function to guide the search process for the optimum hub geometry. The resulting three dimensionally complex hub promises considerable benefits discussed in detail in this paper. A reduction of 15.2% and 16.23% in the total pressure loss and secondary kinetic energy (SKE), respectively, is achieved in the wake region. An improvement of 4.53% in the blade loading is observed. Other complimentary benefits are also listed in the paper. The majority of the benefits are obtained away from the hub region. The contoured hub not only alters the pitchwise static pressure gradient but also acts as a vortex generator in an effort to alleviate the total pressure loss. The results confirm that nonaxisymmetric contouring is an effective method for reducing the losses and thereby improving the performance of the cascade.

Effects of segmented layer suction and micro-vortex generator on a high-load compressor cascade performance

2021 ◽  
pp. 095440622098050
Author(s):  
Shan Ma ◽  
Wuli Chu ◽  
Xiaolin Sun ◽  
Zhengtao Guo ◽  
Song Yan
Keyword(s):  
Boundary Layer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Vortex Generator ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Boundary Layer Suction ◽  
Axial Location ◽  
Micro Vortex Generator ◽  
Suction Slot

The axial location of full-span boundary layer suction is studied to explore the influences of suction slot on the cascade performance. At the design condition, the slot with 50% axial location shows a superior capability to reduce the total pressure loss. At the near stall condition, the more upstream of the suction slot is moved, the more total pressure loss is reduced, and the suction slot with a location of 0.7 axial chord length cannot effectively reduces the total pressure loss in all conditions. Moreover, a rearranged segmented suction slot according to the distribution characteristics of the flow reversal region is developed and compared with full-span boundary layer suction. The segmented suction slot shows significant advantages in delaying the stall occurrence, and the stall point is delayed from 7.9° to 10.0° compared with the baseline. According to a quantitative analysis method selected to measure the performances of flow control technologies, the wake loss is significantly reduced by the segmented suction slot. Finally, a set of micro-vortex generator is introduced in the cascade with a segmented suction slot, and the conclusion indicates that the portion near the end-wall is very effective to reduce the flow loss.

A Numerical Study of Volute Design in Centrifugal Compressor

2001 ◽  
Author(s):  
Weili Yang ◽  
Peter Grant ◽  
James Hitt
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Loss ◽  
Total Pressure ◽  
Numerical Study ◽  
Flow Behavior ◽  
Numerical Results ◽  
Total Pressure Loss ◽  
Pressure Loss Coefficient ◽  
Computational Fluid Dynamics Cfd ◽  
Operating Points

Abstract Our principle goal of this study is to develop a CFD based analysis procedure that could be used to analyze the geometric tradeoffs in scroll geometry when space is limited. In the study, a full centrifugal compressor stage at four different operating points from near surge to near choke is analyzed using Computational Fluid Dynamics (CFD) and laboratory measurement. The study concentrates on scroll performance and its interaction with a vaneless diffuser and impeller. The numerical results show good agreement with test data in scroll circumferential pressure distribution at different ΛAR, total pressure loss coefficient, and pressure distortion at the tongue. The CFD analysis also predicts a reasonable choke point of the stage. The numerical results provide overall flow field in the scroll and diffuser at different operating points. From examining the flow fields, one can have a much better understanding of rather complicated flow behavior such as jet-wake mixing, and choke. One can examine total pressure loss in detail to provide crucial direction for scroll design improvement in areas such as volute tongue, volute cross-section geometry and exit conical diffuser.

Endwall Contouring and Fillet Design for Reducing Losses and Homogenizing the Outflow of a Compressor Cascade

2014 ◽  
Author(s):  
Oliver Reutter ◽  
Stefan Hemmert-Pottmann ◽  
Alexander Hergt ◽  
Eberhard Nicke
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Leading Edge ◽  
Total Pressure Loss ◽  
Wall Region ◽  
Optimized Design ◽  
Compressor Cascade ◽  
Outflow Region ◽  
Endwall Contouring ◽  
Operating Points

The following paper deals with the development of an optimized fillet and an endwall contour for reducing the total pressure loss and for homogenizing the outflow of a highly loaded cascade with a low aspect ratio. The NACA-65 K48 cascade profile without a fillet and without endwall contouring is used as a basis. Optimizations are performed using the DLR in-house tool AutoOpti and the RANS-solver TRACE. Three operating points at an inflow Mach number of 0.67 with different inflow angles are used to secure a wide operating range of the optimized design. At first only a fillet is optimized. The optimized fillet is small at the leading edge and rather high, wide and thick towards the trailing edge. It reduces the total pressure loss and homogenizes the outflow up to a blade height of 20 %. Following this a combined optimization of the endwall and the fillet is performed. The optimized contour leads to the development of a vortex, which changes the secondary flow in such a way, that the corner separation is reduced, which in turn significantly reduces the total pressure loss up to 16 % in the design operating point. The contour in the outflow region leads to a significant homogenization of the outflow in the near wall region.

Location Effect of Boundary Layer Suction on Compressor Hub-Corner Separation

2014 ◽  
Author(s):  
Ping-Ping Chen ◽  
Wei-Yang Qiao ◽  
Karsten Liesner ◽  
Robert Meyer
Keyword(s):  
Boundary Layer ◽  
Pressure Loss ◽  
Total Pressure ◽  
Three Dimensional ◽  
Base Flow ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Corner Separation ◽  
Boundary Layer Suction

The large secondary flow area in the compressor hub-corner region usually leads to three-dimensional separation in the passage with large amounts of total pressure loss. In this paper numerical simulations of a linear high-speed compressor cascade, consisting of five NACA 65-K48 stator profiles, were performed to analyze the flow mechanism of hub-corner separation for the base flow. Experimental validation is used to verify the numerical results. Active control of the hub-corner separation was investigated by using boundary layer suction. The influence of the selected locations of the endwall suction slot was investigated in an effort to quantify the gains of the compressor cascade performance. The results show that the optimal chordwise location should contain the development section of the three-dimensional corner separation downstream of the 3D corner separation onset. The best pitchwise location should be close enough to the vanes’ suction surface. Therefore the optimal endwall suction location is the MTE slot, the one from 50% to 75% chord at the hub, close to the blade suction surface. By use of the MTE slot with 1% suction flow ratio, the total-pressure loss is substantially decreased by about 15.2% in the CFD calculations and 9.7% in the measurement at the design operating condition.

Sign in / Sign up

Export Citation Format

Share Document