Comparison of nickel oxide and palladium nanoparticle loaded on activated carbon for efficient removal of methylene blue

2014 ◽  
Vol 34 (2) ◽  
pp. 153-169 ◽  
Author(s):  
S Arabzadeh ◽  
M Ghaedi ◽  
A Ansari ◽  
F Taghizadeh ◽  
M Rajabi
Keyword(s):  
Electron Microscopy ◽  
Methylene Blue ◽  
Particle Size ◽  
Activated Carbon ◽  
Nickel Oxide ◽  
High Surface ◽  
Average Particle Size ◽  
High Surface Area ◽  
Average Particle ◽  
Efficient Removal

Palladium nanoparticles (Pd-NPs) and nickel oxide nanoparticles (NiO-NPs) were synthesized and loaded on activated carbon (AC). This novel material successfully used for the removal of methylene blue (MB) dye from aqueous medium. Full characterization of both material using X-ray diffraction, transmission electron microscopy, scanning electron microscopy and Brunauer–Emmet–Teller analyses for Pd-NP show their high surface area (>1340 m2/g) and low pore size (<20 Å) and average particle size lower than 45 Å and for NiO-NP show their high surface area (>1316.1554 m2/g) and low pore size (<20 Å) and average particle size lower than 46 Å in addition to high reactive atom and presence of various functional groups. These unique properties make them possible for efficient removal of MB. In batch experimental set-up, optimum conditions for maximum removal of MB by both adsorbents were attained following searching effect of variables such as central composite design. The Langmuir isotherm was found to be highly recommended for fitting the experimental equilibrium data. The kinetic of adsorption of MB on both adsorbents strongly can be fitted by a combination of pseudo-second order and intraparticle diffusion pathway. The experimental result achieved in this article shows the superiority of Pd-NP-AC for MB removal than NiO-NP-AC, so the maximum adsorption capacities of Pd-NP-AC and NiO-NP-AC were 555.5 mg/g and 588.2 mg/g, respectively.

Effects of Preparation Conditions on Characters of Hydrophobic Silica Granular Aerogel and its Applications

2012 ◽  
Vol 600 ◽  
pp. 190-193 ◽  
Author(s):  
Wei Wei ◽  
Jing Yi Zhang ◽  
Li Ping Wu ◽  
Guo Tong Qin
Keyword(s):  
Particle Size ◽  
Ambient Pressure ◽  
High Surface ◽  
Sol Gel ◽  
Average Particle Size ◽  
High Surface Area ◽  
Nitrogen Adsorption ◽  
Ambient Pressure Drying ◽  
Average Particle ◽  
Hydrophobic Silica

The hydrophobic silica granular aerogels were synthesized via sol-gel synthesis followed by ambient pressure drying. The tetraethyloxylane (TEOS) was used as original precursor. The aerogels were analyzed using nitrogen adsorption, scanning electron microscopy (SEM) and laser particle size analyzer. It was found that the aerogel was mesoporous material with high surface area. The aerogels were prepared in grain form by dipping into disperse solution in order to adsorption application. The average particle size of the aerogel was controlled by pH and disperse solution volume. The pH also affected gel time. The aerogels were used to absorb phenol from water. The saturated adsorption amount could reach up to 145 mg•g-1.

scholarly journals High surface area nano-sized La0.6Ca0.4MnO3 perovskite powder prepared by low temperature pyrolysis of a modified citrate gel

2009 ◽  
Vol 7 (4) ◽  
pp. 809-817 ◽  
Author(s):  
Meysam Soleymani ◽  
Ahmad Moheb ◽  
Ezatolah Joudaki
Keyword(s):  
Particle Size ◽  
Surface Area ◽  
Single Phase ◽  
High Surface ◽  
Average Particle Size ◽  
High Surface Area ◽  
Average Particle ◽  
Precursor Method ◽  
Modified Method ◽  
Low Temperature Pyrolysis

AbstractSingle phase nanocrystalline La0.6Ca0.4MnO3 powder was synthesized by both the usual and a modified citrate gel precursor method, and the effects on the formation of homogeneous nano-sized powder with a perovskite structure were investigated. In the modified method, single phase La0.6Ca0.4MnO3 powder with an average particle size of 17.2 nm was obtained when the powder was pyrolyzed at 520°C for 2 h. Its specific surface area was 40.7 m2 g−1, about 4-fold larger than that of powder made by the usual citrate gel method.

Synthesis and Characterization of Water-Soluble Monolayer-Protected Gold Nanoparticles

2011 ◽  
Vol 415-417 ◽  
pp. 617-620 ◽  
Author(s):  
Yan Su ◽  
Ying Yun Lin ◽  
Yu Li Fu ◽  
Fan Qian ◽  
Xiu Pei Yang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Particle Size ◽  
Gold Nanoparticles ◽  
Average Particle Size ◽  
Water Soluble ◽  
Synthesis And Characterization ◽  
Average Particle ◽  
Transmission Electron

Water-soluble gold nanoparticles (AuNPs) were prepared using 2-mercapto-4-methyl-5- thiazoleacetic acid (MMTA) as a stabilizing agent and sodium borohydride (NaBH4) as a reducing agent. The AuNPs product was analyzed by transmission electron microscopy (TEM), UV-vis absorption spectroscopy and Fourier transform infrared spectroscopy (FTIR). The TEM image shows that the particles were well-dispersed and their average particle size is about 5 nm. The UV-vis absorption and FTIR spectra confirm that the MMTA-AuNPs was stabilized by the carboxylate ions present on the surface of the AuNPs.

scholarly journals Microporous activated carbon developed from KOH activated biomass waste: surface mechanistic study of methylene blue dye adsorption

2021 ◽  
Author(s):  
Ali H. Jawad ◽  
Ahmed Saud Abdulhameed ◽  
Noor Nazihah Bahrudin ◽  
Nurul Nadiah Mohd Firdaus Hum ◽  
S. N. Surip ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
Sugarcane Bagasse ◽  
High Surface ◽  
High Surface Area ◽  
Dye Adsorption ◽  
Type I ◽  
Order Kinetic ◽  
Bagasse Waste

Abstract In this work, sugarcane bagasse waste (SBW) was used as a lignocellulosic precursor to develop a high surface area activated carbon (AC) by thermal treatment of the SBW impregnated with KOH. This sugarcane bagasse waste activated carbon (SBWAC) was characterized by means of crystallinity, porosity, surface morphology and functional groups availability. The SBWAC exhibited Type I isotherm which corresponds to microporosity with high specific surface area of 709.3 m2/g and 6.6 nm of mean pore diameter. Further application of SBWAC as an adsorbent for methylene blue (MB) dye removal demonstrated that the adsorption process closely followed the pseudo-second order kinetic and Freundlich isotherm models. On the other hand, thermodynamic study revealed the endothermic nature and spontaneity of MB dye adsorption on SBWAC with high acquired adsorption capacity (136.5 mg/g). The MB dye adsorption onto SBWAC possibly involved electrostatic interaction, H-bonding and π-π interaction. This work demonstrates SBW as a potential lignocellulosic precursor to produce high surface area AC that can potentially remove more cationic dyes from the aqueous environment.

Changes in Particle Size Distributions on a Fixed Bed of Granular Activated Carbon

1986 ◽  
Vol 18 (1) ◽  
pp. 31-42 ◽  
Author(s):  
E. A. Shpirt ◽  
K. T. Alben
Keyword(s):  
New York ◽  
Particle Size ◽  
Activated Carbon ◽  
Average Particle Size ◽  
Fixed Bed ◽  
Treatment Plant ◽  
Granular Activated Carbon ◽  
Water Treatment Plant ◽  
Average Diameter ◽  
Average Particle

The particle size distribution at different bed depths of a fixed bed of granular activated carbon (GAC) has been monitored during 50 weeks of a pilot column run at the Waterford, New York potable water treatment plant. Initial backwashing resulted in significant stratification of GAC in the column: larger particles (average diameter 1.18 mm) settled in the bottom of the column (105 cm), and smaller particles (average diameter 0.97 mm) were concentrated near the top (24 cm), compared to samples of unstratified virgin Calgon F400 (average diameter 1.09 mm). During column loading and initial backwashing, more fines were created than were present in the virgin GAC (average 6.5% of GAC fines in the &gt; 40 mesh fraction, compared to only 0.3% in the &gt; 40 mesh fraction for virgin Calgon F400). After 50 weeks of service there was an overall trend toward a smaller average particle size (0.9 mm) with development of a more regular pattern of bed stratification (1.08 mm at the bottom and 0.75 mm at the top). These changes are attributed to breaking of large particles (12-20 mesh) and creation of intermediate size particles (20-30 and 30-40 mesh).

scholarly journals Synthesis of activated carbon from biowaste of fir bark for methylene blue removal

2019 ◽  
Vol 6 (9) ◽  
pp. 190523 ◽  
Author(s):  
Lu Luo ◽  
Xi Wu ◽  
Zeliang Li ◽  
Yalan Zhou ◽  
Tingting Chen ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Nonlinear Models ◽  
Low Cost ◽  
High Surface ◽  
High Surface Area ◽  
Raw Material ◽  
Maximum Adsorption Capacity ◽  
Koh Activation ◽  
Mb Adsorption

Activated carbon (AC) was successfully prepared from low-cost forestry fir bark (FB) waste using KOH activation method. Morphology and texture properties of ACFB were studied by scanning and high-resolution transmission electron microscopies (SEM and HRTEM), respectively. The resulting fir bark-based activated carbon (ACFB) demonstrated high surface area (1552 m 2 g −1 ) and pore volume (0.84 cm 3 g −1 ), both of which reflect excellent potential adsorption properties of ACFB towards methylene blue (MB). The effect of various factors, such as pH, initial concentration, adsorbent content as well as adsorption duration, was studied individually. Adsorption isotherms of MB were fitted using all three nonlinear models (Freundlich, Langmuir and Tempkin). The best fitting of MB adsorption results was obtained using Freundlich and Temkin. Experimental results showed that kinetics of MB adsorption by our ACFB adsorbent followed pseudo-second-order model. The maximum adsorption capacity obtained was 330 mg g −1 , which indicated that FB is an excellent raw material for low-cost production of AC suitable for cationic dye removal.

The Aggregation Study and Characterization of Silver Nanoparticles

2017 ◽  
Vol 263 ◽  
pp. 165-169
Author(s):  
Silvia Chowdhury ◽  
Faridah Yusof ◽  
Nadzril Sulaiman ◽  
Mohammad Omer Faruck
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Particle Size ◽  
Silver Nanoparticles ◽  
Absorption Spectrum ◽  
Average Particle Size ◽  
Average Particle ◽  
Transmission Electron ◽  
Vis Spectroscopy

In this article, we have studied the process of silver nanoparticles (AgNPs) aggregation and to stop aggregation 0.3% Polyvinylpyrrolidone (PVP) was used. Aggregation study carried out via UV-vis spectroscopy and it is reported that the absorption spectrum of spherical silver nanoparticles were found a maximum peak at 420 nm wavelength. Furthermore, Transmission Electron Microscopy (TEM) were used to characterized the size and shape of AgNPs, where the average particle size is around 10 to 25 nm in diameter and the AgNPs shape is spherical. Next, Dynamic Light Scattering (DLS) were used, owing to observed size distribution and self-correlation of AgNPs.

Magnetic Fe3O4@C nanoparticles as adsorbents for removal of amoxicillin from aqueous solution

2013 ◽  
Vol 69 (1) ◽  
pp. 147-155 ◽  
Author(s):  
Babak Kakavandi ◽  
Ali Esrafili ◽  
Anoushiravan Mohseni-Bandpi ◽  
Ahmad Jonidi Jafari ◽  
Roshanak Rezaei Kalantary
Keyword(s):  
Electron Microscopy ◽  
Activated Carbon ◽  
Kinetic Models ◽  
High Surface ◽  
High Surface Area ◽  
Order Kinetic ◽  
Magnetic Composites ◽  
Factors Affecting ◽  
Transmission Electron ◽  
Pseudo Second Order

In the present study, powder activated carbon (PAC) combined with Fe3O4 magnetite nanoparticles (MNPs) were used for the preparation of magnetic composites (MNPs-PAC), which was used as an adsorbent for amoxicillin (AMX) removal. The properties of magnetic activated carbon were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, Brunaeur, Emmett and Teller and vibrating sample magnetometer. The operational factors affecting adsorption such as pH, contact time, adsorbent dosage, initial AMX concentration and temperature were studied in detail. The high surface area and saturation magnetization for the synthesized adsorbent were found to be 671.2 m2/g and 6.94 emu/g, respectively. The equilibrium time of the adsorption process was 90 min. Studies of adsorption equilibrium and kinetic models revealed that the adsorption of AMX onto MNPs-PAC followed Freundlich and Langmuir isotherms and pseudo-second-order kinetic models. The calculated values of the thermodynamic parameters, such as ΔG°, ΔH° and ΔS° demonstrated that the AMX adsorption was endothermic and spontaneous in nature. It could be concluded that MNPs-PAC have a great potential for antibiotic removal from aquatic media.

Sign in / Sign up

Export Citation Format

Share Document