scholarly journals Beryllium Standard Update

2019 ◽  
Vol 67 (5) ◽  
pp. 264-264
Author(s):  
Jennan A. Phillips

The updated Occupational Safety and Health Administration’s (OSHA) beryllium standard for general industry, construction, and shipyards reduced exposure limits for this known human carcinogen and became effective in 2018. Occupational and environmental health nurses need to monitor updates recently proposed for general industry to clarify implementation of the standard.

2000 ◽  
Author(s):  
LuAnn Gibson

Abstract There are numerous aspects of the electronics demanufacturing industry that may be scrutinized by Occupational Safety and Health regulators. In older computer equipment, there may be materials that have since been banned from use in industry, such as PCBs. Workers disassembling electronic equipment need to be able to recognize components containing this hazardous material. Disassemblers are also exposed to lifting and cutting hazards in their activities. Those who shred or grind their electronics may be exposed to particulated heavy metals or silica, as well as dangerous levels of noise. When electronic components are removed from circuit boards, melting the solder will release lead fumes that must be properly ventilated. Recent and pending changes in OSHA requirements will affect electronics demanufacturers. Forklift standards were revised March 1, 1999, silica exposure limits may soon be reduced, and an ergonomics standard is pending. Universal and waste must be properly handled and stored in ways that comply with regulations and protect the safety and health of the workers. As a new but growing industry, electronics demanufacturers and recylers must remain aware of potential errors that could cost tens of thousands of dollars in OSHA fines or workers’ compensation claims.


2017 ◽  
Vol 2017 (1) ◽  
pp. 2017149
Author(s):  
Patrik Sartz ◽  
Srijan Aggarwal

In-situ burning (ISB) is an efficient and important response tool in a wide range of conditions from open water and very open drift ice (herders) to consolidated ice (self-contained). Herding agents provide a means to thicken and then burn uncontained slicks that would otherwise be too thin to ignite. In this project we assessed the impacts on ambient air quality in the vicinity of the location following ISB tests on crude oil herded and ignited from the air in a large purpose built test pond outside of Fairbanks Alaska. We measured downwind and in-the-smoke-plume, concentrations of respirable particulate matter sizes (PM2.5) and seven different combustion gases (CO, CO2, NO, NO2, NOx, SO2, & VOCs) during five ISB tests, with sampling instruments placed 6–12 m away from the source area. It was also investigated if the herding agent was detectable in the air borne plume. Although in this study we did not use instrument and methods specifically approved by the Occupational Safety and Health Administration (OSHA) and the National Institute for Occupational Safety and Health (NIOSH), to provide a context the study results were compared with exposure limits provided by these agencies. From our results downwind, in the smoke plume, concentrations of particulate matter and SO2 were found to significantly exceed (P <0.01) NIOSH and OSHA exposure limits, while the remaining compounds measured were significantly below (P <0.01) established NIOSH and OSHA exposure limits. In addition, GC/MS Analysis of aerosol samples collected utilizing a flow meter and carbon sorbent tubes in the smoke plume, the silicone based functional group of the applied OP-40 herding agent was not detected in the collected samples. The concentrations measured in this study in the vicinity of the ISB site, lasted for less than ten minutes, before drifting downwind and becoming greatly diluted. These results provide information which might be helpful towards developing guidelines for worker safety in spill response situations.


2022 ◽  
Vol 10 (1) ◽  
pp. 79-88
Author(s):  
Sri Haryanti ◽  
Bambang Suwerda

 This study aims to produce learning videos that are feasible as learning media. The resulting video is a Spirometer Practice Tutorial Video in the Occupational Safety and Health (K3) subject for students of the Environmental Health Department of the Health Ministry of Health Yogyakarta. The method used in research is the method of research and development (Research and Development). This development research uses the Borg & Gall development procedure model which is simplified by the Puslitjaknov Team (2008: 11) with the following steps: 1) Analyzing the product to be developed, 2) Developing the initial product, 3) Expert validation and revision, 4) Testing small-scale field and revisions, 5). Large-scale field trials and final products. The research location was carried out at the Hyperkes Laboratory of Environmental Health Department. This research was conducted in July - September 2020. The results showed that the Spirometer Practice Tutorial video in the occupational safety and health course can be used as a learning medium or learning resource for students, especially for the K3 (Occupational Health Safety) practical course in the Environmental Health Department. the feasibility level is 86.84 5%. Keywords: Learning Media , Video Tutorial, K3 Practice Course


Sign in / Sign up

Export Citation Format

Share Document