Effects of processing conditions on powder particle size and morphology in centrifugal atomisation of tin

2004 ◽  
Vol 47 (2) ◽  
pp. 168-172 ◽  
Author(s):  
J.W. Xie ◽  
Y.Y. Zhao ◽  
J.J. Dunkley
RSC Advances ◽  
2015 ◽  
Vol 5 (18) ◽  
pp. 13331-13340 ◽  
Author(s):  
T. N. Ng ◽  
X. Q. Chen ◽  
K. L. Yeung

Flow-synthesis of mesoporous silica allows deliberate and precise control over the size and shapes and enables the preparation of complex microstructures (i.e., hollow spheres).


2014 ◽  
Vol 936 ◽  
pp. 1694-1700
Author(s):  
Zhi Wei Li ◽  
Kai Yong Jiang ◽  
Fei Wang ◽  
Ji Liang Zhang

This paper mainly introduces the mechanism of microwave heating: electric conduction loss, eddy current loss and arc discharge. The microwave heating behavior of 316 stainless steel powder body which made by gel casting was investigated in the paper. Experiments on different microwave power, powder particle size, and the content of auxiliary heating material showed that the smaller the powder particle size, the larger microwave power and auxiliary heating materials help 316 stainless steel body for sintering.


2021 ◽  
Vol 11 (14) ◽  
pp. 6578
Author(s):  
Aleksandra Jedlińska ◽  
Alicja Barańska ◽  
Dorota Witrowa-Rajchert ◽  
Ewa Ostrowska-Ligęza ◽  
Katarzyna Samborska

This paper discusses the physicochemical properties of powders obtained by spray drying of cloudy beetroot juice, using dehumidified air in variants with or without carriers. The inlet air temperature was 130 °C or 90 °C, and the addition of the carriers was at a ratio of juice to carrier solids of 3:2. In the obtained powders, the following physicochemical properties were determined: water content and water activity, apparent density, loose and tapped density, porosity, flowability, particle size and morphology, and the content and retention of betalains. It was possible to dry cloudy beetroot juice without the use of carriers at low temperatures (90 or 130 °C). The 100% beetroot powders were characterized by satisfactory physicochemical properties, often better than those with carriers (including lower hygroscopicity and higher color saturation and yield). A lower loss of betalains was found for the powders with the addition of carriers. The best process yields were obtained for the powder without carriers at 130 °C and 90 °C.


2007 ◽  
Vol 336-338 ◽  
pp. 140-142
Author(s):  
Jun Jie Hao ◽  
Xiao Hui Wang ◽  
Shi Yun Lin ◽  
Long Tu Li

Na0.5Bi0.5TiO3 (NBT) is considered to be an excellent candidate for lead-free piezoelectric ceramics. In this study, we propose a hydrothermal method for the preparation of single phase NBT powder at relatively low treatment-temperature. The particle size and morphology of the synthesized powders were examined by SEM. The powders were further pressed into disk and sintered at 1120°C/2h in air, and its properties and microstructure were compared with traditionally prepared samples.


2014 ◽  
Vol 46 (3) ◽  
pp. 365-375
Author(s):  
N. Labus ◽  
S. Mentus ◽  
Z.Z. Djuric ◽  
M.V. Nikolic

The influence of air and nitrogen atmosphere during heating on TiO2 nano and micro sized powders as well as sintered polycrystalline specimens was analyzed. Sintering of TiO2 nano and micro powders in air atmosphere was monitored in a dilatometer. Non compacted nano and micro powders were analyzed separately in air and nitrogen atmospheres during heating using thermo gravimetric (TG) and differential thermal analysis (DTA). The anatase to rutile phase transition temperature interval is influenced by the powder particle size and atmosphere change. At lower temperatures for nano TiO2 powder a second order phase transition was detected by both thermal techniques. Polycrystalline specimens obtained by sintering from nano powders were reheated in the dilatometer in nitrogen and air atmosphere, and their shrinkage is found to be different. Powder particle size influence, as well as the air and nitrogen atmosphere influence was discussed.


2016 ◽  
Vol 43 (2) ◽  
pp. 0203007
Author(s):  
闫岸如 Yan Anru ◽  
杨恬恬 Yang Tiantian ◽  
王燕灵 Wang Yanling ◽  
马志红 Ma Zhihong ◽  
杜云 Du Yun ◽  
...  

2020 ◽  
Vol 989 ◽  
pp. 816-820
Author(s):  
Roman Sergeevich Khmyrov ◽  
R.R. Ableyeva ◽  
Tatiana Vasilievna Tarasova ◽  
A.V. Gusarov

Mass transfer in the laser-interaction zone at selective laser melting influences the quality of the obtained material. Powder particles displacement during the formation of the single bead is experimentally studied. The so-called denudated zone was visualized by metallography. It was determined that increasing the powder particle size leads to widening the denudated zone. This can signify that the adhesion forces between powder particles prevail over the friction forces.


2014 ◽  
Vol 2 (37) ◽  
pp. 15437-15447 ◽  
Author(s):  
Aziz Abdellahi ◽  
Oncu Akyildiz ◽  
Rahul Malik ◽  
Katsuyo Thornton ◽  
Gerbrand Ceder

Using calculations based on first principles, we demonstrate that the preferred interface in singles LiFePO4 particles depends both on the particle size and morphology.


Sign in / Sign up

Export Citation Format

Share Document