scholarly journals On the modeling and simulation of coupled adsorption and thermosolutal convection in supercritical carbon dioxide

2022 ◽  
Vol 69 (1) ◽  
Author(s):  
Housseyn Smahi ◽  
Djilali Ameur ◽  
Joanna Dib ◽  
Isabelle Raspo
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Critical Point ◽  
Mass Fraction ◽  
Numerical Study ◽  
Thermosolutal Convection ◽  
Thin Boundary Layer ◽  
Heat Transfer Efficiency ◽  
Mass And Heat Transfer ◽  
Dilute Mixture

AbstractIn this paper, we present a numerical study along with an exhaustive adsorption investigation in a binary dilute mixture model nearby the solvent’s critical point in a configuration relevant for soil remediation. By means of this model, mass and heat transfer efficiency were qualitatively and quantitatively discussed through this work. The convergence of the solution was evaluated on the values of the Nusselt and Sherwood numbers. The results reveal intense convection expanding into the cavity close to the critical point, thus enabling homogeneous adsorption of the solute. Moreover, the mass fraction perturbation isolines exhibit the existence, along the adsorbent plate, of a thin boundary layer which becomes thinner when approaching the critical point.

A Numerical Study of Turbulent Boundary Layer Flow Over a Flat Surface With a Single Dimple

2000 ◽  
Author(s):  
Mark E. Kithcart ◽  
David E. Klett
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Boundary Layer Flow ◽  
Flat Surface ◽  
Numerical Study ◽  
Heat Transfer Augmentation ◽  
Study Results ◽  
Turbulent Boundary Layer Flow ◽  
Layer Flow

Abstract Turbulent boundary layer flow over a flat surface with a single dimple has been investigated numerically using the FLUENT CFD software package, and compared to an experiment by Ezerskii and Shekhov [1989], which studied the same configuration. The impetus for this work developed as a result of previous studies. Kithcart and Klett [1996], and Afanas’yev and Chudnovskiy [1992], showed that dimpled surfaces enhance heat transfer comparably to surfaces with protrusion roughness elements, but with a much lower drag penalty. However, the actual physical mechanisms involved in this phenomena were only partially known prior this study. Results obtained numerically are in good agreement with the experiment, most notably the confirmation of the existence of a region of enhanced heat transfer created by interaction of the flow with the dimple. In particular, the simulation indicates that heat transfer augmentation is a consequence of the development of a stagnation flow region within the dimple geometry, and the existence of coherent vortical structures which create a periodic flow-field within and immediately downstream of the dimple. This periodicity appears to govern the magnitude of the heat transfer augmentation.

scholarly journals Numerical Study of Viscoelastic Micropolar Heat Transfer from a Vertical Cone for Thermal Polymer Coating

2019 ◽  
Vol 8 (1) ◽  
pp. 449-460 ◽  
Author(s):  
K. Madhavi ◽  
V. Ramachandra Prasad ◽  
A. Subba Rao ◽  
O. Anwar Bég ◽  
A. Kadir
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Angular Velocity ◽  
Numerical Study ◽  
Relaxation Times ◽  
Viscoelastic Model ◽  
Deborah Number ◽  
Convection Boundary Layer ◽  
Density Parameter ◽  
R Ratio

Abstract A mathematical model is developed to study laminar, nonlinear, non-isothermal, steady-state free convection boundary layer flow and heat transfer of a micropolar viscoelastic fluid from a vertical isothermal cone. The Eringen model and Jeffery’s viscoelastic model are combined to simulate the non-Newtonian characteristics of polymers, which constitutes a novelty of the present work. The transformed conservation equations for linear momentum, angular momentum and energy are solved numerically under physically viable boundary conditions using a finite difference scheme (Keller Box method). The effects of Deborah number (De), Eringen vortex viscosity parameter (R), ratio of relaxation to retardation times (λ), micro-inertia density parameter (B), Prandtl number (Pr) and dimensionless stream wise coordinate (ξ) on velocity, surface temperature and angular velocity in the boundary layer regime are evaluated. The computations show that with greater ratio of retardation to relaxation times, the linear and angular velocity are enhanced whereas temperature (and also thermal boundary layer thickness) is reduced. Greater values of the Eringen parameter decelerate both the linear velocity and micro-rotation values and enhance temperatures. Increasing Deborah number decelerates the linear flow and Nusselt number whereas it increases temperatures and boosts micro-rotation magnitudes. The study is relevant to non-Newtonian polymeric thermal coating processes.

scholarly journals Cumulative Impact of Micropolar Fluid and Porosity on MHD Channel Flow: A Numerical Study

Coatings ◽  
2022 ◽  
Vol 12 (1) ◽  
pp. 93
Author(s):  
Kottakkaran Sooppy Nisar ◽  
Aftab Ahmed Faridi ◽  
Sohail Ahmad ◽  
Nargis Khan ◽  
Kashif Ali ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Chemical Reaction ◽  
Micropolar Fluid ◽  
Numerical Study ◽  
Nonlinear Differential Equations ◽  
X Rays ◽  
Cumulative Impact ◽  
Transfer Rates ◽  
Mass And Heat Transfer ◽  
The Impact

The mass and heat transfer magnetohydrodynamic (MHD) flows have a substantial use in heat exchangers, electromagnetic casting, X-rays, the cooling of nuclear reactors, mass transportation, magnetic drug treatment, energy systems, fiber coating, etc. The present work numerically explores the mass and heat transportation flow of MHD micropolar fluid with the consideration of a chemical reaction. The flow is taken between the walls of a permeable channel. The quasi-linearization technique is utilized to solve the complex dynamical coupled and nonlinear differential equations. The consequences of the preeminent parameters are portrayed via graphs and tables. A tabular and graphical comparison evidently reveals a correlation of our results with the existing ones. A strong deceleration is found in the concentration due to the effect of a chemical reaction. Furthermore, the impact of the magnetic field force is to devaluate the mass and heat transfer rates not only at the lower but at the upper channel walls, likewise.

Thermal performance enhancement in a wedge duct with in-line pin fins combined with vortex generators

2019 ◽  
Vol 29 (8) ◽  
pp. 2545-2565
Author(s):  
Safeer Hussain ◽  
Jian Liu ◽  
Lei Wang ◽  
Bengt Ake Sunden
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Thermal Performance ◽  
Performance Enhancement ◽  
Numerical Study ◽  
Vortex Generators ◽  
Content Type ◽  
Pin Fin ◽  
Pin Fins ◽  
Cooling Enhancement

Purpose The purpose of this paper is to enhance the heat transfer and thermal performance in the trailing edge region of the vane with vortex generators (VGs). Design/methodology/approach This numerical study presents the enhancement of thermal performance in the trailing part of a gas turbine blade. In the trailing part, generally, pin fins are used either in staggered or in-line arrangements to enhance the heat transfer. In this study, based on the idea from heat exchangers, pin fins are combined with VGs. A pair of VGs is embedded in the boundary layer upstream of each pin fin in the first row of the pin fin array having an in-line configuration. The effects of the VG angle relative to the streamwise direction and streamwise distance between the pin fin and VGs are investigated at various Reynolds numbers. Findings The results indicated that the endwall heat transfer is enhanced with the addition of VGs and the heat transfer from the surfaces of the pin fins. The level of heat transfer enhancement compared to the case without VGs is more significant at high Reynolds number. The surfaces of the VGs also show a significant amount of heat transfer. Study of the angle of the attack suggested that a high angle of attack is more appropriate for pin fin cooling enhancement whereas an intermediate gap between the VGs and pin fins shows considerable improvement of thermal performance compared to the small and large gaps. The phenomenon of heat transfer augmentation with the VGs is demonstrated by the flow field. It shows that the enhancement of heat transfer is governed by the mixing of the flow as a result of the interaction of vortices generated by the VGs and pin fins. Originality/value VGs are used to disturb the thermal boundary layer. It shows that heat transfer is augmented as a result of the interaction of vortices associated with VGs and pin fins.

A Numerical Study of Impulsively Started External Convection at Microscale

2014 ◽  
Vol 31 (1) ◽  
pp. 79-90
Author(s):  
K. Ramadan
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Thermal Boundary Layer ◽  
Numerical Study ◽  
Velocity Slip ◽  
Transition Time ◽  
Surface Cooling ◽  
Linear Ordinary Differential Equations

ABSTRACTImpulsively started external convection at microscale level is studied numerically in both planar and axisymmetric geometries. Using similarity transformation, the resulting coupled partial and non-linear ordinary differential equations are simultaneously solved by finite differences together with a well established ordinary differential equation solver, over a range of problem parameters. Rarefaction effects within the slip flow regime on the thermal boundary layer response, heat transfer rate and transition time when system experiences sudden changes in surface temperature are analyzed, and a comparison between sudden surface cooling and heating is presented. The results show that the thermal boundary layer thickness, heat transfer rate and the transition time is considerably influenced by the degree of rarefaction. The transition time tends to be less sensitive with increasing rarefaction. The velocity slip and temperature jump factors are found to have opposite effects on the transition time and the heat transfer rate, with the velocity slip factor having the most profound influence on these parameters.

Study of Heat Transfer Characteristics in the Boundary Layer of a Visco-Elastic Fluid Under Varying Influencing Parameters

2007 ◽  
Author(s):  
P. Anuradha ◽  
S. Krishnambal
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Numerical Study ◽  
Numerical Technique ◽  
Heat Transfer Characteristics ◽  
Elastic Fluid ◽  
Transfer Characteristics ◽  
Dimensional Parameters ◽  
Influencing Parameters ◽  
Sheet Stretching

The heat transfer characteristics of a visco-elastic fluid within the boundary layer formed by the passage of a sheet stretching at a uniform rate through it are studied under varying influencing parameters using a numerical technique. The influence of considering or ignoring elastic deformation in the thermal analysis is studied in the presence of chosen values of non-dimensional parameters like Prandtl number (Pr) and Eckert number (E). Two cases of sheet surface conditions are considered — (i) PST case involving prescribed surface temperature and (ii) PHF case involving prescribed heat flux at the surface. The results of this numerical study are diagrammatically represented with appropriate conclusions drawn on the influence of the above parameters considered in isolation or together. The trend of results is seen to agree well with those of other researchers who used other solution techniques. A judious choice of the above two principal non-dimensional parameters is suggested for application to a cooling process typical of a polymer extrusion industry.

Sign in / Sign up

Export Citation Format

Share Document