On the use of dispersive APVO GPR curves for thin-bed properties estimation: Theory and application to fracture characterization

Geophysics ◽  
2009 ◽  
Vol 74 (1) ◽  
pp. J1-J12 ◽  
Author(s):  
Jacques Deparis ◽  
Stéphane Garambois
Keyword(s):  
Ground Penetrating Radar ◽  
Inverse Method ◽  
Phase Variation ◽  
Fractured Media ◽  
Data Set ◽  
Fracture Characterization ◽  
Propagation Effects ◽  
Phase Liquid ◽  
Ground Penetrating ◽  
Homogeneous Formation

The presence of a thin layer embedded in any formation creates complex reflection patterns caused by interferences within the thin bed. The generated reflectivity amplitude variations with offset have been increasingly used in seismic interpretation and more recently tested on ground-penetrating radar (GPR) data to characterize nonaqueous-phase liquid contaminants. Phase and frequency sensitivities of the reflected signals are generally not used, although they contain useful information. The present study aims to evaluate the potential of these combined properties to characterize a thin bed using GPR data acquired along a common-midpoint (CMP) survey, carried out to assess velocity variations in the ground. It has been restricted to the simple case of a thin bed embedded within a homogeneous formation, a situation often encountered in fractured media. Dispersive properties ofthe dielectric permittivity of investigated materials (homogeneous formation, thin bed) are described using a Jonscher parameterization, which permitted study of the dependency of amplitude and phase variation with offset (APVO) curves on frequency and thin-bed properties (filling nature, aperture). In the second part, we discuss and illustrate the validity of the thin-bed approximation as well as simplify assumptions and make necessary careful corrections to convert raw CMP data into dispersive APVO curves. Two different strategies are discussed to correct the data from propagation effects: a classical normal-moveout approach and an inverse method. Finally, the proposed methodology is applied to a CMP GPR data set acquired along a vertical cliff. It allowed us to extract the characteristics of a subvertical fracture with satisfying resolution and confidence. The study motivates interest to use dispersion dependency of the reflection coefficient variations for thin-bed characterization.

scholarly journals Particle Center Supported Plane for Subsurface Target Classification based on Full Polarimetric Ground Penetrating Radar

2019 ◽  
Vol 11 (4) ◽  
pp. 405
Author(s):  
Xuan Feng ◽  
Haoqiu Zhou ◽  
Cai Liu ◽  
Yan Zhang ◽  
Wenjing Liang ◽  
...  
Keyword(s):  
Ground Penetrating Radar ◽  
Decomposition Methods ◽  
Support Vector ◽  
Classification Methods ◽  
Target Classification ◽  
Data Set ◽  
Particle Center ◽  
Ground Penetrating ◽  
New Criterion

The subsurface target classification of ground penetrating radar (GPR) is a popular topic in the field of geophysics. Among the existing classification methods, geometrical features and polarimetric attributes of targets are primarily used. As polarimetric attributes contain more information of targets, polarimetric decomposition methods, such as H-Alpha decomposition, have been developed for target classification of GPR in recent years. However, the classification template used in H-Alpha classification is preset depending on the experience of synthetic aperture radar (SAR); therefore, it may not be suitable for GPR. Moreover, many existing classification methods require excessive human operation, particularly when outliers exist in the sample (the data set containing the features of targets); therefore, they are not efficient or intelligent. We herein propose a new machine learning method based on sample centers, i.e., particle center supported plane (PCSP). The sample center is defined as the point with the smallest sum of distances from all points in the same sample, which is considered as a better representation of the sample without significant effect of the outliers. In this proposed method, particle swarm optimization (PSO) is performed to obtain the sample centers; the new criterion for subsurface target classification is achieved. We applied this algorithm to full polarimetric GPR data measured in the laboratory and outdoors. The results indicate that, comparing with support vector machine (SVM) and classical H-Alpha classification, this new method is more efficient and the accuracy is relatively high.

Helicopter-borne ground-penetrating radar investigations on temperate alpine glaciers: A comparison of different systems and their abilities for bedrock mapping

Geophysics ◽  
2016 ◽  
Vol 81 (1) ◽  
pp. WA119-WA129 ◽  
Author(s):  
Anja Rutishauser ◽  
Hansruedi Maurer ◽  
Andreas Bauder
Keyword(s):  
Ground Penetrating Radar ◽  
Low Frequency ◽  
Large Data ◽  
Internal Reflection ◽  
Swiss Alps ◽  
Reflection Band ◽  
Data Set ◽  
Investigation Area ◽  
Attractive Option ◽  
Ground Penetrating

On the basis of a large data set, comprising approximately 1200 km of profile lines acquired with different helicopter-borne ground-penetrating radar (GPR) systems over temperate glaciers in the western Swiss Alps, we have analyzed the possibilities and limitations of using helicopter-borne GPR surveying to map the ice-bedrock interface. We have considered data from three different acquisition systems including (1) a low-frequency pulsed system hanging below the helicopter (BGR), (2) a stepped frequency system hanging below the helicopter (Radar Systemtechnik GmbH [RST]), and (3) a commercial system mounted directly on the helicopter skids (Geophysical Survey Systems Incorporated [GSSI]). The systems showed considerable differences in their performance. The best results were achieved with the BGR system. On average, the RST and GSSI systems yielded comparable results, but we observed significant site-specific differences. A comparison with ground-based GPR data found that the quality of helicopter-borne data is inferior, but the compelling advantages of airborne surveying still make helicopter-borne data acquisition an attractive option. Statistical analyses concerning the bedrock detectability revealed not only large differences between the different acquisition systems but also between different regions within our investigation area. The percentage of bedrock reflections identified (with respect to the overall profile length within a particular region) varied from 11.7% to 68.9%. Obvious factors for missing the bedrock reflections included large bedrock depths and steeply dipping bedrock interfaces, but we also observed that internal features within the ice body may obscure bedrock reflections. In particular, we identified a conspicuous “internal reflection band” in many profiles acquired with the GSSI system. We attribute this feature to abrupt changes of the water content within the ice, but more research is required for a better understanding of the nature of this internal reflection band.

Interpolating wide-aperture ground-penetrating radar beyond aliasing

Geophysics ◽  
2015 ◽  
Vol 80 (2) ◽  
pp. H13-H22 ◽  
Author(s):  
Saulo S. Martins ◽  
Jandyr M. Travassos
Keyword(s):  
Ground Penetrating Radar ◽  
Real Data ◽  
Velocity Model ◽  
Data Sets ◽  
Inversion Problem ◽  
Data Set ◽  
Isolated Points ◽  
Antarctic Continent ◽  
Ground Penetrating ◽  
The Antarctic

Most of the data acquisition in ground-penetrating radar is done along fixed-offset profiles, in which velocity is known only at isolated points in the survey area, at the locations of variable offset gathers such as a common midpoint. We have constructed sparse, heavily aliased, variable offset gathers from several fixed-offset, collinear, profiles. We interpolated those gathers to produce properly sampled counterparts, thus pushing data beyond aliasing. The interpolation methodology estimated nonstationary, adaptive, filter coefficients at all trace locations, including at the missing traces’ corresponding positions, filled with zeroed traces. This is followed by an inversion problem that uses the previously estimated filter coefficients to insert the new, interpolated, traces between the original ones. We extended this two-step strategy to data interpolation by employing a device in which we used filter coefficients from a denser variable offset gather to interpolate the missing traces on a few independently constructed gathers. We applied the methodology on synthetic and real data sets, the latter acquired in the interior of the Antarctic continent. The variable-offset interpolated data opened the door to prestack processing, making feasible the production of a prestack time migrated section and a 2D velocity model for the entire profile. Notwithstanding, we have used a data set obtained in Antarctica; there is no reason the same methodology could not be used somewhere else.

Continuous and simultaneous measurement of reflector depth and average soil-water content with multichannel ground-penetrating radar

Geophysics ◽  
2008 ◽  
Vol 73 (4) ◽  
pp. J15-J23 ◽  
Author(s):  
Holger Gerhards ◽  
Ute Wollschläger ◽  
Qihao Yu ◽  
Philip Schiwek ◽  
Xicai Pan ◽  
...  
Keyword(s):  
Water Content ◽  
Soil Water ◽  
Soil Water Content ◽  
Ground Penetrating Radar ◽  
Synthetic Data ◽  
Evaluation Procedure ◽  
Noninvasive Technique ◽  
Data Set ◽  
Large Variability ◽  
Ground Penetrating

Ground-penetrating radar is a fast noninvasive technique that can monitor subsurface structure and water-content distribution. To interpret traveltime information from single common-offset measurements, additional assumptions, such as constant permittivity, usually are required. We present a fast ground-penetrating-radar measurement technique using a multiple transmitter-and-receiver setup to measure simultaneously the reflector depth and average soil-water content. It can be considered a moving minicommon-midpoint measurement. For a simple analysis, we use a straightforward evaluation procedure that includes two traveltimes to the same reflector, obtained from different antenna separations. For a more accurate approach, an inverse evaluation procedure is added, using traveltimes obtained from all antenna separations at one position and its neighboring measurement locations. The evaluation of a synthetic data set with a lateral variability in reflector depth and an experimental example with a large variability in soil-water content are introduced to demonstrate the applicability for field-scale measurements. The crucial point for this application is the access to absolute traveltimes, which are difficult to determine accurately from common-offset measurements.

scholarly journals Stochastic Collocation Applications in Computational Electromagnetics

2018 ◽  
Vol 2018 ◽  
pp. 1-13 ◽  
Author(s):  
Dragan Poljak ◽  
Silvestar Šesnić ◽  
Mario Cvetković ◽  
Anna Šušnjara ◽  
Hrvoje Dodig ◽  
...  
Keyword(s):  
Ground Penetrating Radar ◽  
Stochastic Models ◽  
Human Exposure ◽  
Input Data ◽  
Review Paper ◽  
Computational Electromagnetics ◽  
Stochastic Collocation ◽  
Data Set ◽  
Mean And Variance ◽  
Ground Penetrating

The paper reviews the application of deterministic-stochastic models in some areas of computational electromagnetics. Namely, in certain problems there is an uncertainty in the input data set as some properties of a system are partly or entirely unknown. Thus, a simple stochastic collocation (SC) method is used to determine relevant statistics about given responses. The SC approach also provides the assessment of related confidence intervals in the set of calculated numerical results. The expansion of statistical output in terms of mean and variance over a polynomial basis, via SC method, is shown to be robust and efficient approach providing a satisfactory convergence rate. This review paper provides certain computational examples from the previous work by the authors illustrating successful application of SC technique in the areas of ground penetrating radar (GPR), human exposure to electromagnetic fields, and buried lines and grounding systems.

scholarly journals Combining Signal Features of Ground-Penetrating Radar to Classify Moisture Damage in Layered Building Floors

2021 ◽  
Vol 11 (19) ◽  
pp. 8820
Author(s):  
Tim Klewe ◽  
Christoph Strangfeld ◽  
Tobias Ritzer ◽  
Sabine Kruschwitz
Keyword(s):  
Ground Penetrating Radar ◽  
High Sensitivity ◽  
Moisture Damage ◽  
Depth Information ◽  
Insulation Material ◽  
Data Set ◽  
Piped Water ◽  
Signal Features ◽  
Ground Penetrating ◽  
Non Destructive

To date, the destructive extraction and analysis of drilling cores is the main possibility to obtain depth information about damaging water ingress in building floors. The time- and cost-intensive procedure constitutes an additional burden for building insurances that already list piped water damage as their largest item. With its high sensitivity for water, a ground-penetrating radar (GPR) could provide important support to approach this problem in a non-destructive way. In this research, we study the influence of moisture damage on GPR signals at different floor constructions. For this purpose, a modular specimen with interchangeable layers is developed to vary the screed and insulation material, as well as the respective layer thickness. The obtained data set is then used to investigate suitable signal features to classify three scenarios: dry, damaged insulation, and damaged screed. It was found that analyzing statistical distributions of A-scan features inside one B-scan allows for accurate classification on unknown floor constructions. Combining the features with multivariate data analysis and machine learning was the key to achieve satisfying results. The developed method provides a basis for upcoming validations on real damage cases.

Traveltime tomography of crosshole ground-penetrating radar based on an arctangent functional with compactness constraints

Geophysics ◽  
2017 ◽  
Vol 82 (3) ◽  
pp. H1-H14 ◽  
Author(s):  
Shufan Hu ◽  
Yonghui Zhao ◽  
Tan Qin ◽  
Chunfeng Rao ◽  
Cong An
Keyword(s):  
Ground Penetrating Radar ◽  
Gradient Algorithm ◽  
Order Differential Operator ◽  
Data Set ◽  
Actual Structure ◽  
Trade Off ◽  
Traveltime Tomography ◽  
Ground Penetrating ◽  
The Impact ◽  
Low Order

Regularization has been an effective technique to provide unique and stable solutions for crosshole ground-penetrating radar (GPR) traveltime tomography. The traditional form of this method, in which a low-order differential operator was used, commonly yields a smooth solution that may not be appropriate when anomalies occur in block patterns, such as voids or irregular objects. The minimum support (MS) functional can be used to improve the resolution of blocky structures; however, in crosshole GPR traveltime tomography, the MS functional is unable to resolve residual artifacts, whose departure from an a priori model are smaller than the focusing parameter selected from a trade-off curve. In addition, it would result in severe instability and yield a trade-off curve with poorly defined corners when the focusing parameter nears the precision of the apparatus. We have developed a new stabilizing functional based on the arctangent (AT) function that effectively removes the artificially small values in the crosshole GPR traveltime tomography, and ultimately is more efficient because it does not require the user to select a focusing parameter. We inverted three 2D synthetic data sets based on the reweighted regularized conjugate gradient algorithm. Compared with the low-order differential and MS functional, the user will be able to clearly distinguish the anomaly boundary using this method, which will yield results that are closer to the actual structure. We also discussed the impact of some influencing factors caused by the noise contained in the data, the central frequency of the antenna, the anomalous trends, and the ray coverage angle. We further inverted an experimental data set to test the effectiveness and robustness of the method.

Predicting material properties of concrete from ground-penetrating radar attributes

2020 ◽  
pp. 147592172097699
Author(s):  
Isabel M Morris ◽  
Vivek Kumar ◽  
Branko Glisic
Keyword(s):  
Compressive Strength ◽  
Physical Properties ◽  
Ground Penetrating Radar ◽  
Material Properties ◽  
Regression Models ◽  
Physical Property ◽  
Portland Cement Concrete ◽  
Instantaneous Amplitude ◽  
Data Set ◽  
Ground Penetrating

We present here a laboratory-based experimental protocol that seeks to establish and characterize the relationship between ground-penetrating radar attributes and the mechanical properties (density, porosity, and compressive strength) of typical industry concrete mixes. The experimental data consist of ground-penetrating radar attributes from 900 MHz radargrams that correspond to simultaneously measured physical properties of Portland cement concrete, alkali-activated concrete, and cement mortar. Appropriate regression models are trained and tested on this data set to predict each physical property from ground-penetrating radar attributes. From a small selection of individual attributes, including total phase and intensity, trained random forest regression models predict porosity ( R2 = 0.83 from the instantaneous amplitude), density ( R2 = 0.67 from the intensity attribute), and compressive strength ( R2 = 0.51 from instantaneous amplitude). These novel relationships between physical properties and ground-penetrating radar attributes indicate that material properties could be predicted from the attributes of ordinary ground-penetrating radar scans of concrete.

Sign in / Sign up

Export Citation Format

Share Document