Refraction wavefield migration

Geophysics ◽  
2020 ◽  
Vol 85 (6) ◽  
pp. Q27-Q37
Author(s):  
Yang Shen ◽  
Jie Zhang
Keyword(s):  
Signal To Noise Ratio ◽  
Surface Velocity ◽  
Data Set ◽  
Near Surface ◽  
Depth Migration ◽  
Reflection Data ◽  
Imaging Tool ◽  
Imaging Results ◽  
Migration Method ◽  
Single Method

Refraction methods are often applied to model and image near-surface velocity structures. However, near-surface imaging is very challenging, and no single method can resolve all of the land seismic problems across the world. In addition, deep interfaces are difficult to image from land reflection data due to the associated low signal-to-noise ratio. Following previous research, we have developed a refraction wavefield migration method for imaging shallow and deep interfaces via interferometry. Our method includes two steps: converting refractions into virtual reflection gathers and then applying a prestack depth migration method to produce interface images from the virtual reflection gathers. With a regular recording offset of approximately 3 km, this approach produces an image of a shallow interface within the top 1 km. If the recording offset is very long, the refractions may follow a deep path, and the result may reveal a deep interface. We determine several factors that affect the imaging results using synthetics. We also apply the novel method to one data set with regular recording offsets and another with far offsets; both cases produce sharp images, which are further verified by conventional reflection imaging. This method can be applied as a promising imaging tool when handling practical cases involving data with excessively weak or missing reflections but available refractions.

Seismic imaging and velocity analysis for an Alberta Foothills seismic survey

Geophysics ◽  
2001 ◽  
Vol 66 (3) ◽  
pp. 721-732 ◽  
Author(s):  
Lanlan Yan ◽  
Larry R. Lines
Keyword(s):  
Seismic Imaging ◽  
Migration Velocity ◽  
Surface Velocity ◽  
Seismic Survey ◽  
Velocity Analysis ◽  
Prestack Depth Migration ◽  
Near Surface ◽  
Depth Migration ◽  
Migration Velocity Analysis ◽  
Imaging Results

Seismic imaging of complex structures from the western Canadian Foothills can be achieved by applying the closely coupled processes of velocity analysis and depth migration. For the purposes of defining these structures in the Shaw Basing area of western Alberta, we performed a series of tests on both synthetic and real data to find optimum imaging procedures for handling large topographic relief, near‐surface velocity variations, and the complex structural geology of steeply dipping formations. To better understand the seismic processing problems, we constructed a typical foothills geological model that included thrust faults and duplex structures, computed the model responses, and then compared the performance of different migration algorithms, including the explicit finite difference (f-x) and Kirchhoff integral methods. When the correct velocity was used in the migration tests, the f-x method was the most effective in migration from topography. In cases where the velocity model was not assumed known, we determined a macrovelocity model by performing migration/velocity analysis by using smiles and frowns in common image gathers and by using depth‐focusing analysis. In applying depth imaging to the seismic survey from the Shaw Basing area, we found that imaging problems were caused partly by near‐surface velocity problems, which were not anticipated in the modeling study. Several comparisons of different migration approaches for these data indicated that prestack depth migration from topography provided the best imaging results when near‐surface velocity information was incorporated. Through iterative and interpretive migration/velocity analysis, we built a macrovelocity model for the final prestack depth migration.

Prestack processing of land data with complex topography

Geophysics ◽  
1995 ◽  
Vol 60 (6) ◽  
pp. 1875-1886 ◽  
Author(s):  
Sara Rajasekaran ◽  
George A. McMechan
Keyword(s):  
Wave Equation ◽  
Processing System ◽  
Essential Elements ◽  
Surface Velocity ◽  
Velocity Variation ◽  
Data Set ◽  
Near Surface ◽  
Depth Migration ◽  
Elevation Changes ◽  
Data Extrapolation

A new wave‐equation–based prestack seismic processing system is proposed. This system has only two essential elements; velocity analysis and depth migration. This approach applies truly surface‐consistent statics corrections, regardless of the amount of elevation, change or of near‐surface velocity variation. It uses tomography for estimating the details of shallow velocities and a finite‐difference solution of the two‐way wave‐equation both for computation of image times and for data extrapolation in migration. A field data set that violates most of the assumptions in conventional common midpoint (CMP) processing, because of severe elevation changes and near‐surface velocity variations, is successfully processed. The final depth section reveals a complicated fold‐thrust geometry that was not visible after CMP processing.

Depth migration with the near surface: A case study for mineral exploration in China

2019 ◽  
Vol 7 (4) ◽  
pp. T809-T817
Author(s):  
Guofeng Liu ◽  
Xiaohong Meng ◽  
Yu Liu
Keyword(s):  
Mineral Exploration ◽  
Velocity Model ◽  
Small Scale ◽  
Seismic Reflection Data ◽  
Near Surface ◽  
Imaging Quality ◽  
Depth Migration ◽  
Original Surface ◽  
Imaging Results ◽  
Migration Method

Seismic reflection data used in mineral exploration are usually of poor quality because of rough topography and small-scale heterogeneities. However, there is an increasing demand for accurate imaging processes that can obtain such data. Here, we have developed a practical rugged depth migration method based on the finite-difference one-way wave equation. It can be used to improve imaging quality when faced with rough topography and complex geologic features. First, synthetic data are used to illustrate the errors and problems that cause unsatisfactory imaging results. This is usually because no consideration is given to rough topography during conventional processing procedures. To address this, a depth migration method that begins with the rugged topography is introduced. It can be used to produce better images. Real data from mineral exploration activities in Fujian, China, are then used to demonstrate the practical use of this method. We also compare two computational processes: The first corrects the data back to the original surface and then builds a velocity model before conducting rugged depth migration; the second process involves performing rugged depth migration on processed data featuring a smoothed surface following short-wavelength static correction and residual correction. The imaging results indicate that the section obtained from the processed data has better quality. They also indicate that the imaging quality of the original surface is affected by the built velocity model, which cannot include near-surface and small-scale structures.

scholarly journals Crustal velocity structure of the Superior and Grenville provinces of the southeastern Canadian Shield

1997 ◽  
Vol 34 (8) ◽  
pp. 1167-1184 ◽  
Author(s):  
S. Winardhi ◽  
R. F. Mereu
Keyword(s):  
Greenstone Belt ◽  
Velocity Structure ◽  
Canadian Shield ◽  
Crustal Thickening ◽  
Surface Velocity ◽  
Data Set ◽  
Tectonic Zone ◽  
Near Surface ◽  
Abitibi Greenstone Belt ◽  
Sudbury Structure

The 1992 Lithoprobe Abitibi–Grenville Seismic Refraction Experiment was conducted using four profiles across the Grenville and Superior provinces of the southeastern Canadian Shield. Delay-time analysis and tomographic inversion of the data set demonstrate significant lateral and vertical variations in crustal velocities from one terrane to another, with the largest velocity values occurring underneath the Central Gneiss and the Central Metasedimentary belts south of the Grenville Front. The Grenville Front Tectonic Zone is imaged as a southeast-dipping region of anomalous velocity gradients extending to the Moho. The velocity-anomaly maps suggest an Archean crust may extend, horizontally, 140 km beneath the northern Grenville Province. Near-surface velocity anomalies correlate well with the known geology. The most prominent of these is the Sudbury Structure, which is well mapped as a low-velocity basinal structure. The tomography images also suggest underthrusting of the Pontiac and Quetico subprovinces beneath the Abitibi Greenstone Belt. Wide-angle PmP signals, indicate that the Moho varies from a sharp discontinuity south of the Grenville Front to a rather diffuse and flat boundary under the Abitibi Greenstone Belt north of the Grenville Front. A significant crustal thinning near the Grenville Front may indicate post-Grenvillian rebound and (or) the extensional structure of the Ottawa–Bonnechere graben. Crustal thickening resulting from continental collision may explain the tomographic images showing the Moho is 4–5 km deeper south of the Grenville Front.

Overthrust imaging with tomo‐datuming: A case study

Geophysics ◽  
1998 ◽  
Vol 63 (1) ◽  
pp. 25-38 ◽  
Author(s):  
Xianhuai Zhu ◽  
Burke G. Angstman ◽  
David P. Sixta
Keyword(s):  
Velocity Model ◽  
Surface Velocity ◽  
Time Shift ◽  
Lateral Velocity ◽  
Prestack Depth Migration ◽  
Near Surface ◽  
Depth Migration ◽  
Static Corrections ◽  
Velocity Variations ◽  
Kirchhoff Method

Through the use of iterative turning‐ray tomography followed by wave‐equation datuming (or tomo‐datuming) and prestack depth migration, we generate accurate prestack images of seismic data in overthrust areas containing both highly variable near‐surface velocities and rough topography. In tomo‐datuming, we downward continue shot records from the topography to a horizontal datum using velocities estimated from tomography. Turning‐ray tomography often provides a more accurate near‐surface velocity model than that from refraction statics. The main advantage of tomo‐datuming over tomo‐statics (tomography plus static corrections) or refraction statics is that instead of applying a vertical time‐shift to the data, tomo‐datuming propagates the recorded wavefield to the new datum. We find that tomo‐datuming better reconstructs diffractions and reflections, subsequently providing better images after migration. In the datuming process, we use a recursive finite‐difference (FD) scheme to extrapolate wavefield without applying the imaging condition, such that lateral velocity variations can be handled properly and approximations in traveltime calculations associated with the raypath distortions near the surface for migration are avoided. We follow the downward continuation step with a conventional Kirchhoff prestack depth migration. This results in better images than those migrated from the topography using the conventional Kirchhoff method with traveltime calculation in the complicated near surface. Since FD datuming is only applied to the shallow part of the section, its cost is much less than the whole volume FD migration. This is attractive because (1) prestack depth migration usually is used iteratively to build a velocity model, so both efficiency and accuracy are important factors to be considered; and (2) tomo‐datuming can improve the signal‐to‐noise (S/N) ratio of prestack gathers, leading to more accurate migration velocity analysis and better images after depth migration. Case studies with synthetic and field data examples show that tomo‐datuming is especially helpful when strong lateral velocity variations are present below the topography.

scholarly journals Using Seismic Attributes in seismotectonic research: an application to the Norcia's Mw = 6.5 earthquake (30th October 2016) in Central Italy

2019 ◽  
Author(s):  
Maurizio Ercoli ◽  
Emanuele Forte ◽  
Massimiliano Porreca ◽  
Ramon Carbonell ◽  
Cristina Pauselli ◽  
...  
Keyword(s):  
Seismic Reflection ◽  
Central Italy ◽  
Seismic Attributes ◽  
Seismic Attribute ◽  
Data Set ◽  
Epicentral Zone ◽  
Seismic Reflection Data ◽  
Near Surface ◽  
Reflection Data ◽  
Attribute Analysis

Abstract. In seismotectonic studies, seismic reflection data are a powerful tool to unravel the complex deep architecture of active faults. Such tectonic structures are usually mapped at surface through traditional geological surveying whilst seismic reflection data may help to trace their continuation from the near-surface down to hypocentral depth. In this study, we propose the application of the seismic attributes technique, commonly used in seismic reflection exploration by oil industry, to seismotectonic research for the first time. The study area is a geologically complex region of Central Italy, recently struck by a long-lasting seismic sequence including a Mw 6.5 main-shock. A seismic reflection data-set consisting of three vintage seismic profiles, currently the only available across the epicentral zone, constitutes a singular opportunity to attempt a seismic attribute analysis. This analysis resulted in peculiar seismic signatures which generally correlate with the exposed surface geologic features, and also confirming the presence of other debated structures. These results are critical, because provide information also on the relatively deep structural setting, mapping a prominent, high amplitude regional reflector that marks the top basement, interpreted as important rheological boundary. Complex patterns of high-angle discontinuities crossing the reflectors have been also identified. These dipping fabrics are interpreted as the expression of fault zones, belonging to the active normal fault systems responsible for the seismicity of the region. This work demonstrates that seismic attribute analysis, even if used on low-quality vintage 2D data, may contribute to improve the subsurface geological interpretation of areas characterized by high seismic potential.

A robust first-arrival picking workflow using convolutional and recurrent neural networks

Geophysics ◽  
2020 ◽  
Vol 85 (5) ◽  
pp. U109-U119
Author(s):  
Pengyu Yuan ◽  
Shirui Wang ◽  
Wenyi Hu ◽  
Xuqing Wu ◽  
Jiefu Chen ◽  
...  
Keyword(s):  
Deep Learning ◽  
Model Building ◽  
Signal To Noise Ratio ◽  
Synthetic Data ◽  
Velocity Model ◽  
Surface Velocity ◽  
Data Sets ◽  
Near Surface ◽  
Segmentation Boundary ◽  
First Arrival

A deep-learning-based workflow is proposed in this paper to solve the first-arrival picking problem for near-surface velocity model building. Traditional methods, such as the short-term average/long-term average method, perform poorly when the signal-to-noise ratio is low or near-surface geologic structures are complex. This challenging task is formulated as a segmentation problem accompanied by a novel postprocessing approach to identify pickings along the segmentation boundary. The workflow includes three parts: a deep U-net for segmentation, a recurrent neural network (RNN) for picking, and a weight adaptation approach to be generalized for new data sets. In particular, we have evaluated the importance of selecting a proper loss function for training the network. Instead of taking an end-to-end approach to solve the picking problem, we emphasize the performance gain obtained by using an RNN to optimize the picking. Finally, we adopt a simple transfer learning scheme and test its robustness via a weight adaptation approach to maintain the picking performance on new data sets. Our tests on synthetic data sets reveal the advantage of our workflow compared with existing deep-learning methods that focus only on segmentation performance. Our tests on field data sets illustrate that a good postprocessing picking step is essential for correcting the segmentation errors and that the overall workflow is efficient in minimizing human interventions for the first-arrival picking task.

Land FWI in the Delaware Basin, west Texas: A case study

2020 ◽  
Vol 39 (5) ◽  
pp. 324-331
Author(s):  
Gary Murphy ◽  
Vanessa Brown ◽  
Denes Vigh
Keyword(s):  
Seismic Data ◽  
Waveform Inversion ◽  
Surface Velocity ◽  
High Signal ◽  
Data Sets ◽  
Data Set ◽  
Low Frequencies ◽  
Near Surface ◽  
Delaware Basin ◽  
West Texas

As part of a wide-reaching full-waveform inversion (FWI) research program, FWI is applied to an onshore seismic data set collected in the Delaware Basin, west Texas. FWI is routinely applied on typical marine data sets with high signal-to-noise ratio (S/N), relatively good low-frequency content, and reasonably long offsets. Land seismic data sets, in comparison, present significant challenges for FWI due to low S/N, a dearth of low frequencies, and limited offsets. Recent advancements in FWI overcome limitations due to poor S/N and low frequencies making land FWI feasible to use to update the shallow velocities. The chosen area has contrasting and variable near-surface conditions providing an excellent test data set on which to demonstrate the workflow and its challenges. An acoustic FWI workflow is used to update the near-surface velocity model in order to improve the deeper image and simultaneously help highlight potential shallow drilling hazards.

scholarly journals Time-lapse imaging using 3D ultra-high-frequency marine seismic reflection data

Geophysics ◽  
2020 ◽  
Vol 85 (2) ◽  
pp. P13-P25
Author(s):  
Michael J. Faggetter ◽  
Mark E. Vardy ◽  
Justin K. Dix ◽  
Jonathan M. Bull ◽  
Timothy J. Henstock
Keyword(s):  
High Frequency ◽  
Seismic Reflection ◽  
High Tide ◽  
Time Lapse ◽  
Data Set ◽  
Seismic Reflection Data ◽  
Near Surface ◽  
Ultra High Frequency ◽  
Reflection Data ◽  
Marine Seismic

Time-lapse (4D) seismic imaging is now widely used as a tool to map and interpret changes in deep reservoirs as well as investigate dynamic, shallow hydrological processes in the near surface. However, there are very few examples of time-lapse analysis using ultra-high-frequency (UHF; kHz range) marine seismic reflection data. Exacting requirements for navigation can be prohibitive for acquiring coherent, true-3D volumes. Variable environmental noise can also lead to poor amplitude repeatability and make it difficult to identify differences that are related to real physical changes. Overcoming these challenges opens up a range of potential applications for monitoring the subsurface at decimetric resolution, including geohazards, geologic structures, as well as the bed-level and subsurface response to anthropogenic activities. Navigation postprocessing was incorporated to improve the acquisition and processing workflow for the 3D Chirp subbottom profiler and provide stable, centimeter-level absolute positioning, resulting in well-matched 3D data and mitigating 4D noise for data stacked into [Formula: see text] common-midpoint bins. Within an example 4D data set acquired on the south coast of the UK, interpretable differences are recorded within a shallow gas blanket. Reflections from the top and bottom of a gas pocket are imaged at low tide, whereas at high tide only the upper reflection is imaged. This case study demonstrates the viability of time-lapse UHF 3D seismic reflection for quantitative mapping of decimeter-scale changes within the shallow marine subsurface.

Sign in / Sign up

Export Citation Format

Share Document