Prediction of Broadband Ground-Motion Time Histories: The Case of Tehran, Iran

2013 ◽  
Vol 29 (2) ◽  
pp. 633-660 ◽  
Author(s):  
Hamid Zafarani ◽  
Hesam Vahidifard ◽  
Anooshirvan Ansari

The northern Tehran fault (NTF) is potentially capable of causing large earth-quakes (Mmax ~ 7.2) in a very densely populated area of northern Tehran, Iran. Due to the lack of recorded strong motion data for earthquakes on the fault, a hybrid simulation method is used to calculate broadband (0.1–20 Hz) ground-motion time histories at bedrock level for deterministic earthquake scenarios on the NTF. Low-frequency components of motion (0.1–1.0 Hz) are calculated using a deterministic approach and the discrete wave number-finite element method in a regional one-dimensional (1-D) velocity model. High frequencies (1.0–20.0 Hz) are calculated by the stochastic finite fault method based on dynamic corner frequency. The results were validated by comparing the simulated peak values and response spectra with the empirical ground motion models available for the area and the Modified Mercalli intensity (MMI) observations from historical earthquakes of the region.

2017 ◽  
Author(s):  
Duruo Huang ◽  
Wenqi Du

Abstract. In performance-based seismic design, ground-motion time histories are needed for analyzing dynamic responses of nonlinear structural systems. However, the number of strong-motion data at design level is often limited. In order to analyze seismic performance of structures, ground-motion time histories need to be either selected from recorded strong-motion database, or numerically simulated using stochastic approaches. In this paper, a detailed procedure to select proper acceleration time histories from the Next Generation Attenuation (NGA) database for several cities in Taiwan is presented. Target response spectra are initially determined based on a local ground motion prediction equation under representative deterministic seismic hazard analyses. Then several suites of ground motions are selected for these cities using the Design Ground Motion Library (DGML), a recently proposed interactive ground-motion selection tool. The selected time histories are representatives of the regional seismic hazard, and should be beneficial to earthquake studies when comprehensive seismic hazard assessments and site investigations are yet available. Note that this method is also applicable to site-specific motion selections with the target spectra near the ground surface considering the site effect.


2021 ◽  
Author(s):  
Nesrin Yenihayat ◽  
Eser Çaktı ◽  
Karin Şeşetyan

<p>One of the major earthquakes that resulted in intense damages in Istanbul and its neighborhoods took place on 10 July 1894. The 1894 earthquake resulted in 474 losses of life and 482 injuries. Around 21,000 dwellings were damaged, which is a number that corresponds to 1/7 of the total dwellings of the city at that time. Without any doubt, the exact loss of life was higher. Because of the censorship, the exact loss numbers remained unknown. There is still no consensus about its magnitude, epicentral location, and rupture of length. Even though the hardness of studying with historical records due to their uncertainties and discrepancies, researchers should enlighten the source parameters of the historical earthquakes to minimize the effect of future disasters especially for the cities located close to the most active fault lines as Istanbul. The main target of this study is to enlighten possible source properties of the 1894 earthquake with the help of observed damage distribution and stochastic ground motion simulations. In this paper, stochastic based ground motion scenarios will be performed for the 10 July 1894 Istanbul earthquake, using a finite fault simulation approach with a dynamic corner frequency and the results will be compared with our intensity map obtained from observed damage distributions. To do this, in the first step, obtained damage information from various sources has been presented, evaluated, and interpreted. Secondly, we prepared an intensity map associated with the 1894 earthquake based on macro-seismic information, and damage analysis and classification. For generating ground motions with a stochastic finite fault simulation approach, the EXSIM 2012 software has been used. Using EXSIM, several scenarios are modeled with different source, path, and site parameters. Initial source properties have been obtained from findings of our previous study on the simulation of the 26 September 2019 Silivri (Istanbul) earthquake with Mw 5.8. With the comparison of spatial distributions of the ground motion intensity parameters to the obtained damage and intensity maps, we estimate the optimum location and source parameters of the 1894 Earthquake.</p>


2020 ◽  
Author(s):  
Sreeram Reddy Kotha ◽  
Graeme Weatherill ◽  
Dino Bindi ◽  
Fabrice Cotton

<p>Ground-Motion Models (GMMs) characterize the random distributions of ground-motions for a combination of earthquake source, wave travel-path, and the effected site’s geological properties. Typically, GMMs are regressed over a compendium of strong ground-motion recordings collected from several earthquakes recorded at multiple sites scattered across a variety of geographical regions. The necessity of compiling such large datasets is to expand the range of magnitude, distance, and site-types; in order to regress a GMM capable of predicting realistic ground-motions for rare earthquake scenarios, e.g. large magnitudes at short distances from a reference rock site. The European Strong-Motion (ESM) dataset is one such compendium of observations from a few hundred shallow crustal earthquakes recorded at a several hundred seismic stations in Europe and Middle-East.</p><p>We developed new GMMs from the ESM dataset, capable of predicting both the response spectra and Fourier spectra in a broadband of periods and frequencies, respectively. However, given the clear tectonic and geological diversity of the data, possible regional and site-specific differences in observed ground-motions needed to be quantified; whilst also considering the possible contamination of data from outliers. Quantified regional differences indicate that high-frequency ground-motions attenuate faster with distance in Italy compared to the rest of Europe, as well as systematically weaker ground-motions from central Italian earthquakes. In addition, residual analyses evidence anisotropic attenuation of low frequency ground-motions, imitating the pattern of shear-wave energy radiation. With increasing spatial variability of ground-motion data, the GMM prediction variability apparently increases. Hence, robust mixed-effects regressions and residual analyses are employed to relax the ergodic assumption.</p><p>Large datasets, such as the ESM, NGA-West2, and from KiK-Net, provide ample opportunity to identify and evaluate the previously hypothesized event-to-event, region-to-region, and site-to-site differences in ground-motions. With the appropriate statistical methods, these variabilities can be quantified and applied in seismic hazard and risk predictions. We intend to present the new GMMs: their development, performance and applicability, prospective improvements and research needs.</p>


1995 ◽  
Vol 22 (1) ◽  
pp. 190-196
Author(s):  
René Tinawi ◽  
André Filiatrault ◽  
Pierre Léger

An earthquake of magnitude ML = 4.3 occurred near Napierville, Quebec, on November 16, 1993. An accelerograph at the liquefaction, storage, and regasification plant of Gaz Metropolitain in Montreal, about 55 km from the epicentre, recorded the ground motion. Although the maximum accelerations and velocities from this event are small, the acceleration time histories do confirm the high energy content in the very short period range. The recorded ground motion and corresponding absolute acceleration response spectra are presented and various attenuation relationships, proposed for eastern North America, are utilized to compare the measured and predicted ground motion parameters. Key words: Napierville earthquake, attenuation relationships, acceleration spectra, strong motion records.


1987 ◽  
Vol 3 (2) ◽  
pp. 263-287 ◽  
Author(s):  
N. A. Abrahamson ◽  
B. A. Bolt ◽  
R. B. Darragh ◽  
J. Penzien ◽  
Y. B. Tsai

SMART 1 is the first large digital array of strong-motion seismographs specially designed for engineering and seismological studies of the generation and near-field properties of earthquakes. Since the array began operation in September 1980, it has recorded over 3000 accelerogram traces from 48 earthquakes ranging in local magnitude ( ML) from 3.6 to 7.0. Peak ground accelerations have been recorded up to 0.33g and 0.34g on the horizontal and vertical components, respectively. Epicentral distances have ranged from 3 km 200 km from the array center, and focal depths have ranged from shallow to 100 km. The recorded earthquakes had both reverse and strike-slip focal mechanisms associated with the subduction zone and transform faults. These high quality, digital, ground motions provide a varied resource for earthquake engineering research. Earthquake engineering studies of the SMART 1 ground motion data have led to advances in knowledge in several cases: for example, on frequency-dependent incoherency of free-surface ground motions over short distances, on response of linear systems to multiple support excitations, on attenuation of peak ground-motion parameters and response spectra, on site torsion and phasing effects, and on the identification of wave types. Accelerograms from individual strong-motion seismographs do not, in general, provide such information. This review describes the SMART 1 array and the recorded earthquakes with special engineering applications. Also, it tabulates the unfiltered peak array accelerations, displays some of the recorded ground motion time histories, and summarizes the main engineering research that has made use of SMART 1 data.


2018 ◽  
Vol 18 (3) ◽  
pp. 152-160
Author(s):  
Yuliastuti Yuliastuti ◽  
Euis Etty A ◽  
Topan Setiadipura

A thorough understanding of an earthquake is very important to provide a descriptive knowledge and in the same time as a prescriptive knowledge for the future development. In particular, it is essential for site selection and structural design development of nuclear reactor and other critical facilities. Ground motion acceleration time history is an important raw information to understand the earthquake and specific geological condition of where the data is recorded. This paper presented the development of strong-motion analysis code, called Winston-BATAN, which able to interpret ground motion time history. The analysis scope of the code including the ground motion parameters such as peak ground acceleration, several additional seismic intensity parameters, strong motion duration, its frequency content via Fast Fourier Transformation and response spectra analysis. Being developed based on an open source Python programming language, Winston-BATAN is flexible for exploratory study to exploit the ground motion time history and easily improve to accommodate additional features. This code able to read input from PEER NGA type file or a simple time and acceleration data type of ground motion. Analysis results of Winston-BATAN shows a very good agreement compare to the results from the standard tools Seismosignal® 2018 Software, in addition flexibility of this code, in particular, to explore the response spectra from the ground motion time history is demonstrated.


2017 ◽  
Vol 17 (10) ◽  
pp. 1725-1739
Author(s):  
Duruo Huang ◽  
Wenqi Du ◽  
Hong Zhu

Abstract. In performance-based seismic design, ground-motion time histories are needed for analyzing dynamic responses of nonlinear structural systems. However, the number of ground-motion data at design level is often limited. In order to analyze seismic performance of structures, ground-motion time histories need to be either selected from recorded strong-motion database or numerically simulated using stochastic approaches. In this paper, a detailed procedure to select proper acceleration time histories from the Next Generation Attenuation (NGA) database for several cities in Taiwan is presented. Target response spectra are initially determined based on a local ground-motion prediction equation under representative deterministic seismic hazard analyses. Then several suites of ground motions are selected for these cities using the Design Ground Motion Library (DGML), a recently proposed interactive ground-motion selection tool. The selected time histories are representatives of the regional seismic hazard and should be beneficial to earthquake studies when comprehensive seismic hazard assessments and site investigations are unavailable. Note that this method is also applicable to site-specific motion selections with the target spectra near the ground surface considering the site effect.


2021 ◽  
pp. 875529302098197
Author(s):  
Jack W Baker ◽  
Sanaz Rezaeian ◽  
Christine A Goulet ◽  
Nicolas Luco ◽  
Ganyu Teng

This manuscript describes a subset of CyberShake numerically simulated ground motions that were selected and vetted for use in engineering response-history analyses. Ground motions were selected that have seismological properties and response spectra representative of conditions in the Los Angeles area, based on disaggregation of seismic hazard. Ground motions were selected from millions of available time series and were reviewed to confirm their suitability for response-history analysis. The processes used to select the time series, the characteristics of the resulting data, and the provided documentation are described in this article. The resulting data and documentation are available electronically.


2002 ◽  
Vol 18 (1) ◽  
pp. 1-17 ◽  
Author(s):  
K. Anastassiadis ◽  
I. E. Avramidis ◽  
P. Panetsos

According to the model of Penzien and Watabe, the three translational ground motion components on a specific point of the ground are statistically noncorrelated along a well-defined orthogonal system of axes p, w, and v, whose orientation remains reasonably stable over time during the strong motion phase of an earthquake. This orthotropic ground motion is described by three generally independent response spectra Sa, Sb, and Sc, respectively. The paper presents an antiseismic design procedure for structures according to the above seismic motion model. This design includes a) determination of the critical orientation of the seismic input, i.e., the orientation that gives the largest response, b) calculation of the maximum and the minimum values of any response quantity, and c) application of either the Extreme Stress Method or the Extreme Force Method for determining the most unfavorable combinations of several stress resultants (or sectional forces) acting concurrently at a specified section of a structural member.


2015 ◽  
Vol 31 (3) ◽  
pp. 1629-1645 ◽  
Author(s):  
Ronnie Kamai ◽  
Norman Abrahamson

We evaluate how much of the fling effect is removed from the NGA database and accompanying GMPEs due to standard strong motion processing. The analysis uses a large set of finite-fault simulations, processed with four different high-pass filter corners, representing the distribution within the PEER ground motion database. The effects of processing on the average horizontal component, the vertical component, and peak ground motion values are evaluated by taking the ratio between unprocessed and processed values. The results show that PGA, PGV, and other spectral values are not significantly affected by processing, partly thanks to the maximum period constraint used when developing the NGA GMPEs, but that the bias in peak ground displacement should not be ignored.


Sign in / Sign up

Export Citation Format

Share Document