Reliability assessment of international design concepts for punching shear retrofitting by use of post-installed shear links

2021 ◽  
pp. 638-645
Author(s):  
P. Mowlavi ◽  
N. Mellios ◽  
P. Spyridis ◽  
A. Strauss
Keyword(s):  
Reliability Assessment ◽  
Punching Shear ◽  
Design Concepts ◽  
Shear Links

Evaluation of design concepts for post-installed punching shear retrofitting

Structures ◽  
2020 ◽  
Vol 27 ◽  
pp. 1710-1721
Author(s):  
Oladimeji B. Olalusi ◽  
Panagiotis Spyridis ◽  
Alfred Strauss
Keyword(s):  
Punching Shear ◽  
Design Concepts

Enhanced reliability assessment of punching shear resistance models for flat slabs without shear reinforcement

2021 ◽  
Vol 226 ◽  
pp. 111319
Author(s):  
Marcus Ricker ◽  
Tânia Feiri ◽  
Konstantin Nille-Hauf ◽  
Viviane Adam ◽  
Josef Hegger
Keyword(s):  
Reliability Assessment ◽  
Shear Resistance ◽  
Punching Shear ◽  
Shear Reinforcement ◽  
Flat Slabs

Assessment of Design Concepts for Post-installed Punching Shear Retrofitting

2021 ◽  
pp. 179-190
Author(s):  
Oladimeji B. Olalusi ◽  
Puneh Mowlavi ◽  
Nikolaos Mellios ◽  
Panagiotis Spyridis
Keyword(s):  
Punching Shear ◽  
Design Concepts

High resolution at low voltage: A new approach

1989 ◽  
Vol 47 ◽  
pp. 76-77
Author(s):  
Arthur V. Jones
Keyword(s):  
Low Voltage ◽  
Emission Sources ◽  
New Approach ◽  
Design Concepts ◽  
Probe Diameter ◽  
Low Voltage Operation ◽  
Sufficient Intensity ◽  
Electron Microscopes ◽  
Scanning Electron Microscopes ◽  
Immersion Type

With the introduction of field-emission sources and “immersion-type” objective lenses, the resolution obtainable with modern scanning electron microscopes is approaching that obtainable in STEM and TEM-but only with specific types of specimens. Bulk specimens still suffer from the restrictions imposed by internal scattering and the need to be conducting. Advances in coating techniques have largely overcome these problems but for a sizeable body of specimens, the restrictions imposed by coating are unacceptable.For such specimens, low voltage operation, with its low beam penetration and freedom from charging artifacts, is the method of choice.Unfortunately the technical dificulties in producing an electron beam sufficiently small and of sufficient intensity are considerably greater at low beam energies — so much so that a radical reevaluation of convential design concepts is needed.The probe diameter is usually given by

Experience Design Applied to Research

2019 ◽  
Vol 2 (1) ◽  
Author(s):  
Andrea CAPRA ◽  
Ana BERGER ◽  
Daniela SZABLUK ◽  
Manuela OLIVEIRA
Keyword(s):  
Information Technology ◽  
Product Development ◽  
Design Process ◽  
Development Process ◽  
Product Development Process ◽  
Experience Design ◽  
Low Resolution ◽  
Design Concepts ◽  
Innovative Products ◽  
Technological Products

An accurate understanding of users' needs is essential for the development of innovative products. This article presents an exploratory method of user centered research in the context of the design process of technological products, conceived from the demands of a large information technology company. The method is oriented - but not restricted - to the initial stages of the product development process, and uses low-resolution prototypes and simulations of interactions, allowing users to imagine themselves in a future context through fictitious environments and scenarios in the ambit of ideation. The method is effective in identifying the requirements of the experience related to the product’s usage and allows rapid iteration on existing assumptions and greater exploration of design concepts that emerge throughout the investigation.

Optimization of Process Parameters in Stir Casting of Hybrid Metal Matrix (LM25/SiC/B4C) Composite Using Taguchi Method

2017 ◽  
Vol 13 (9) ◽  
pp. 6475-6479
Author(s):  
M. Arulraj ◽  
P.K. Palani ◽  
L. Venkatesh
Keyword(s):  
Taguchi Method ◽  
Matrix Material ◽  
Base Material ◽  
Stir Casting ◽  
Aluminium Matrix ◽  
Matrix Composites ◽  
Design Concepts ◽  
Specific Strength ◽  
Optimization Of Process Parameters ◽  
Reinforcement Material

Aluminium based composites exhibit many attractive material properties such as increased stiffness, wear resistance, specific strength and vibration damping and decreased co-efficient of thermal expansion compared with the conventional aluminium alloys. Aluminium Matrix Composites consist of non-metallic reinforcement which offers advantageous properties over base material. Reinforcements like SiC, B4C and Al2O3 are normally preferred to improve the mechanical properties. Here Aluminum LM25 is selected as matrix material while Silicon carbide and Boron carbide are selected as reinforcement material. The fabrication of aluminium matrix was done by stir casting method. In the present study an attempt has been made to investigate the effect of three major stir casting parameters (stir speed, stir duration and preheated temperature of reinforcement material) on stir casting of Aluminium LM25 - SiC - B4C composite. Experiments were conducted based on Taguchi methodology. Taguchi quality design concepts of L9 orthogonal array has been used to determine S/N ratio and through S/N ratio a set of optimum stir casting parameters were obtained. The experimental results confirmed the validity of Taguchi method for enhancing tensile strength of castings. 

Analyzing the accuracy of bank reliability assessment based on official reporting

2020 ◽  
Vol 26 (2) ◽  
pp. 327-348
Author(s):  
O.I. Razumova
Keyword(s):  
Financial Reporting ◽  
Financial Stability ◽  
Systems Approach ◽  
Reliability Assessment ◽  
Financial Statements ◽  
Rating Agencies ◽  
Short Term Forecasting ◽  
One Year ◽  
Key Indicators ◽  
Correct Forecast

Subject. The article considers ratings of banks' reliability. Objectives. The aim is to evaluate the accuracy of existing methodology for bank reliability assessment based on official reporting, to identify patterns between indicators and factors that can affect the financial sustainability of a bank. Methods. The study draws on the comparative analysis of key indicators of bank's financial statements one year prior to the introduction of provisional administration, and evaluates the results of existing methods for analyzing the financial standing of banks. Results. The findings show that those methods that use only official reporting to assess the reliability of banks are not sufficient for short-term forecasting of financial stability. Ratings of the majority of agencies that rest on official reporting have a high percentage of erroneous results, therefore, rating agencies are not able to predict the regulator's decisions regarding a credit institution. Conclusions. Currently, there are no universal methods to determine reliability, which would provide a correct forecast of deteriorated financial position of the bank. It is important to use a systems approach, where financial reporting is not a key component.

Sign in / Sign up

Export Citation Format

Share Document