Water to binder ratio concept in QC

2021 ◽  
pp. 113-123
Author(s):  
Masaki Kitazume
Keyword(s):  
Binder Ratio ◽  
Water To Binder Ratio

Effects of Two Polypropylene Fibers on the Properties of High Strength Concrete

2013 ◽  
Vol 357-360 ◽  
pp. 1328-1331
Author(s):  
Bai Rui Zhou ◽  
Dong Dong Han ◽  
Jian Hua Yang ◽  
Yi Liang Peng ◽  
Guo Xin Li
Keyword(s):  
Portland Cement ◽  
Modulus Of Elasticity ◽  
High Strength Concrete ◽  
Polypropylene Fiber ◽  
High Strength ◽  
Polypropylene Fibers ◽  
Strength Concrete ◽  
Reticular Fiber ◽  
Binder Ratio ◽  
Water To Binder Ratio

Portland cement, crushed stone, sand and superplasticizer were used to obtain a high strength concrete with a low water to binder ratio. A reticular polypropylene fiber and a single polypropylene fiber were used to improve the strength of the high strength concrete, but the effects of the two fibers on the slump and strengths were quite different. The reasons of the differences were the surface area and the modulus of elasticity of the fibers. The results show the reticular fiber was better to used in high strength concretes.

scholarly journals Bond Strength between Glass Fiber Fabrics and Low Water-to-Binder Ratio Mortar: Experimental Characterization

2018 ◽  
Vol 2018 ◽  
pp. 1-10
Author(s):  
Daniel Bohling ◽  
Andrzej Cwirzen ◽  
Karin Habermehl-Cwirzen
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Bond Strength ◽  
Glass Fiber ◽  
Penetration Depth ◽  
Pullout Strength ◽  
Lap Shear Strength ◽  
Lap Shear ◽  
Binder Ratio ◽  
Water To Binder Ratio

Full utilization of mechanical properties of glass fiber fabric-reinforced cement composites is very limited due to a low bond strength between fibers and the binder matrix. An experimental setup was developed and evaluated to correlate the mortar penetration depth with several key parameters. The studied parameters included fresh mortar properties, compressive and flexural strengths of mortar, the fabric/mortar bond strength, fabric pullout strength, and a single-lap shear strength. Results showed that an average penetration of mortar did not exceed 100 µm even at a higher water-to-binder ratio. The maximum particle size of the used fillers should be below an average spacing of single glass fibers, which in this case was less than 20 µm to avoid the sieving effect, preventing effective penetration. The pullout strength was strongly affected by the penetration depth, while the single-lap shear strength was also additionally affected by the mechanical properties of the mortar.

Effect of Fly Ash and Nano-CaCO3 on the Viscosity of Cement Paste

2013 ◽  
Vol 357-360 ◽  
pp. 968-971 ◽  
Author(s):  
Ren Juan Sun ◽  
Zhi Qin Zhao ◽  
Da Wei Huang ◽  
Gong Feng Xin ◽  
Shan Shan Wei ◽  
...  
Keyword(s):  
Fly Ash ◽  
Cement Paste ◽  
Bingham Model ◽  
Reduced Viscosity ◽  
Binder Ratio ◽  
Water To Binder Ratio

The effect of fly ash and nanoCaCO3 on the viscosity of pastes was studied. The rheological value of cement paste was determined by the rotation rheometer NXS-11B. In the study, five different dosages (0%, 20%, 30%, 40%, and 50%) of fly ash and three levels of nanoCaCO3, 0.5%, 1%, and 2.5%, were considered. Viscosity of the pastes, made with fly ash and nanoCaCO3 at a constant water-to-binder ratio of 0.35, were measured and analyzed. The results indicate that the pastes with fly ash or/and nanoCaCO3 still fit the Bingham model. The addition of fly ash reduced viscosity, however, the addition of nanoCaCO3 increased viscosity. The effect of nanoCaCO3 is more significantly than fly ash on viscosity.

High Performance Concrete with Ternary Binders

2018 ◽  
Vol 761 ◽  
pp. 120-123 ◽  
Author(s):  
Vlastimil Bílek ◽  
David Pytlík ◽  
Marketa Bambuchova
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Silica Fume ◽  
High Performance ◽  
Ordinary Portland Cement ◽  
High Performance Concrete ◽  
Fresh Concrete ◽  
Binder Ratio ◽  
Water To Binder Ratio ◽  
Condensed Silica Fume

Use a ternary binder for production of a high performance concrete with a compressive strengths between 120 and 170 MPa is presented. The water to binder ratio of the concrete is 0.225 and the binder is composed of Ordinary Portland Cement (OPC), condensed silica fume (CSF), ground limestone (L), fly ash (FA) and metakaoline (MK). The dosage of (M + CSF) is kept at a constant level for a better workability of fresh concrete. Different workability, flexural and compressive strengths were obtained for concretes with a constant cement and a metakaoline dosage, and for a constant dosage (FA + L) but a different ratio FA / L. An optimum composition was found and concretes for other tests were designed using this composition.

scholarly journals The role of shrinkage reducing admixtures and supplementary cementitious materials in volume stability and strength development

2019 ◽  
Vol 289 ◽  
pp. 02005
Author(s):  
Ioanna Papayianni ◽  
Fotini Kesikidou ◽  
Philip Henes Alt
Keyword(s):  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Strength Development ◽  
Capillary Absorption ◽  
Volume Stability ◽  
Cement Mortars ◽  
Shrinkage Reducing Admixture ◽  
Binder Ratio ◽  
Shrinkage Reducing Admixtures ◽  
Water To Binder Ratio

Shrinkage is one of the main reasons for mortar and concrete failures like curling, crack formation and de-bonding. It is a complex phenomenon due to many factors involved, such as the type and amount of cement, water to binder ratio, binder to aggregates ratio and the type and granulometry of the aggregates, relative humidity, air temperature and the temperature of concrete. To reduce this phenomenon, Shrinkage Reducing Admixtures (SRAs) have been studied over the last 30 years. On the other hand, investigation in the field of Supplementary Cementitious Materials (SCMs) has indicated that their use in concrete may improve its volume stability depending on their percentage and the type of the material. In this paper, the addition of a Shrinkage Reducing Admixture and Supplementary Cementitious Materials like ladle furnace slag, calcareous fly ash and limestone filler, were investigated. Their influence, separately and in combination, in volume stability and strength development of cement mortars was identified. Capillary absorption and open porosity were also determined.

Microscopic Analysis and Study of High-Performance Seawater All-Coral Concrete

2019 ◽  
Vol 815 ◽  
pp. 216-222
Author(s):  
Chao Chen ◽  
Jin Ming Liu ◽  
Yang Yang ◽  
Zhi Guo Guo
Keyword(s):  
Mechanical Properties ◽  
Natural Environment ◽  
High Performance ◽  
Work Performance ◽  
Room Temperature ◽  
Microscopic Analysis ◽  
Internal Curing ◽  
Mix Design ◽  
Binder Ratio ◽  
Water To Binder Ratio

The ocean islands are far from inland and the concrete sandstone aggregates are scarce. In this paper, high-performance seawater all-coral concrete was developed by seawater mixing and room temperature maintenance design, and by optimizing the water-to-binder ratio, regulating internal curing, changing auxiliary cementing materials and blending ratio, incorporating expansion agent, adjusting fiber blending, etc. Combined with the consideration of work performance and mechanical properties, the concrete self-shrinkage is adjusted to further optimize the mix design. The mechanical properties of the optimized high-performance seawater all-coral concrete were studied, and the relevant durability tests were carried out according to the natural environment characteristics of the island. This is of great significance to the construction of island projects, repair and construction, and construction of protective projects [1].

Sign in / Sign up

Export Citation Format

Share Document