An analysis of the influence of oil supply conditions on the thermohydrodynamic performance of a single-groove journal bearing

2003 ◽  
Vol 217 (2) ◽  
pp. 133-144 ◽  
Author(s):  
L Costa ◽  
A. S. Miranda ◽  
M Fillon ◽  
J. C. P. Claro
Keyword(s):  
Film Thickness ◽  
Journal Bearing ◽  
Hydrodynamic Pressure ◽  
Quantitative Information ◽  
Published Data ◽  
Oil Supply ◽  
Supply Pressure ◽  
Minimum Film Thickness ◽  
Theoretical Predictions ◽  
Loss Maximum

In this work a thermohydrodynamic analysis has been developed in order to investigate the influence of oil supply conditions on the performance of a journal bearing. The supply conditions considered were oil supply temperature, supply pressure, groove length and groove location. To carry out this study, the hydrodynamic pressure distribution inside the bearing has been determined using a mass-conserving cavitation model with realistic supply conditions. The energy equation and the heat conduction equation have been used for the determination of oil film and bush temperature distributions. The agreement observed between theoretical predictions and experimental published data is acceptable. Quantitative information shows that the oil supply conditions affect bearing performance parameters in different ways. Oil flowrate was markedly affected by all supply parameters studied. Power loss, maximum bush temperature and minimum film thickness were mainly dependent on oil supply temperature. The effect of supply pressure on minimum film thickness was dependent on groove location. An axial groove located at 90° to the load line gave rise to more favourable bearing performance characteristics.

An Experimental Analysis of Misalignment Effects on Hydrodynamic Plain Journal Bearing Performances

2001 ◽  
Vol 124 (2) ◽  
pp. 313-319 ◽  
Author(s):  
J. Bouyer ◽  
M. Fillon
Keyword(s):  
Film Thickness ◽  
Journal Bearing ◽  
Hydrodynamic Pressure ◽  
Operating Conditions ◽  
Temperature Fields ◽  
Maximum Pressure ◽  
Minimum Film Thickness ◽  
Oil Flow ◽  
Hydrodynamic Effects

The present study deals with the experimental determination of the performance of a 100 mm diameter plain journal bearing submitted to a misalignment torque. Hydrodynamic pressure and temperature fields in the mid-plane of the bearing, temperatures in two axial directions, oil flow rate, and minimum film thickness, were all measured for various operating conditions and misalignment torques. Tests were carried out for rotational speeds ranging from 1500 to 4000 rpm with a maximum static load of 9000 N and a misalignment torque varying from 0 to 70 N.m. The bearing performances were greatly affected by the misalignment. The maximum pressure in the mid-plane decreased by 20 percent for the largest misalignment torque while the minimum film thickness was reduced by 80 percent. The misalignment caused more significant changes in bearing performance when the rotational speed or load was low. The hydrodynamic effects were then relatively small and the bearing offered less resistance to the misalignment.

Improvement of the THD Performance of a Misaligned Plain Journal Bearing

2003 ◽  
Vol 125 (2) ◽  
pp. 334-342 ◽  
Author(s):  
J. Bouyer ◽  
M. Fillon
Keyword(s):  
Film Thickness ◽  
Flow Rate ◽  
Journal Bearing ◽  
Numerical Study ◽  
Axial Flow ◽  
Hydrodynamic Pressure ◽  
Operating Conditions ◽  
Local Defect ◽  
Minimum Film Thickness ◽  
Global Defect

This numerical study deals with the improvement of the thermohydrodynamic performance of a 100 mm plain journal bearing submitted to a constant misalignment torque under steady-state conditions. The performance of the misaligned journal bearing is improved by adding either a local or a global defect to the bearing geometry. The influence on bearing performance of the local defect, situated in the zone of minimum film thickness, is analyzed by using various widths and lengths of defect. A global defect, which is conical in shape and is located at one end of the bearing, is also studied under varying direction and magnitude of misalignment torque. Our main focus was on hydrodynamic pressure, temperature distributions at the film/bush interface, oil flow rate, power losses and film thickness. The defects significantly improved the performance of the bearing. The minimum film thickness increased by more than 60 percent and the temperature decreased, whilst the axial flow rate was barely affected. Thus, the defects can be an effective solution for misaligned bearings when they are submitted to extreme operating conditions.

Profile Design for Misaligned Journal Bearings Subjected to Transient Mixed Lubrication

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Thomas Gu ◽  
Q. Jane Wang ◽  
Shangwu Xiong ◽  
Zhong Liu ◽  
Arup Gangopadhyay ◽  
...  
Keyword(s):  
Film Thickness ◽  
Performance Metrics ◽  
Journal Bearing ◽  
Hydrodynamic Lubrication ◽  
Hydrodynamic Pressure ◽  
Industrial Applications ◽  
Mixed Lubrication ◽  
Asperity Contact ◽  
Minimum Film Thickness ◽  
Profile Design

Misalignment between the shaft and the bearing of a journal bearing set may be inevitable and can negatively impact journal bearing performance metrics in many industrial applications. This work proposes a convex profile design of the journal surface to help counteract the negative effects caused by such a misalignment. A transient mass-conserving hydrodynamic Reynolds equation model with the Patir–Cheng flow factors and the Greenwood–Tripp pressure–gap relationship is developed to conduct the design and analysis. The results reveal that under transient impulse loading, a properly designed journal profile can help enhance the minimum film thickness, reduce mean and peak bearing frictions, and increase bearing durability by reducing the asperity-related wear load. The mechanism for the minimum film thickness improvement due to the profile design is traced to the more even distribution of the hydrodynamic pressure toward the axial center of the bearing. The reason for the reductions of the friction and wear load is identified to be the decreased asperity contact by changing the lubrication regime from mixed lubrication to nearly hydrodynamic lubrication. Parametric studies and a case study are reported to highlight the key points of the profile design and recommendations for profile height selection are made according to misalignment parameters.

scholarly journals Experimental Investigation of the Influence of Supply Temperature and Supply Pressure on the Performance of a Two-Axial Groove Hydrodynamic Journal Bearing

2006 ◽  
Vol 129 (1) ◽  
pp. 98-105 ◽  
Author(s):  
F. P. Brito ◽  
A. S. Miranda ◽  
J. Bouyer ◽  
M. Fillon
Keyword(s):  
Flow Rate ◽  
Journal Bearing ◽  
Hydrodynamic Pressure ◽  
Significant Rise ◽  
Operating Conditions ◽  
Maximum Temperature ◽  
Outlet Temperature ◽  
Oil Supply ◽  
Supply Pressure ◽  
Oil Flow

An experimental study of the influence of oil supply temperature and supply pressure on the performance of a 100mm plain journal bearing with two axial grooves located at ±90deg to the load line was carried out. The hydrodynamic pressure at the mid-plane of the bearing, temperature profiles at the oil-bush and oil-shaft interfaces, bush torque, oil flow rate, and the position of the shaft were measured for variable operating conditions. Shaft rotational speed ranged from 1000 to 4000rpm and two different values of applied load were tested (2 and 10kN). The supply temperature ranged from 35 to 50°C, whereas the oil supply pressure range was 70 to 210kPa. Bearing performance is strongly dependent on the supply conditions. It was found that the existence of the downstream groove significantly affects the temperature profile at the oil-bush interface except for the low load, low feeding pressure cases, where the cooling effect of the upstream groove is significant. Feeding temperature has a strong effect on the minimum film thickness. The increase in maximum temperature is significantly lower than the corresponding increase in supply temperature. Increases in supply pressure lead to a significant rise in oil flow rate but have little effect on the maximum temperature and power-loss, except in the case of the lightly loaded bearing. Shaft temperature was found to be close to the bearing maximum temperature for low applied loads, being significantly smaller than this value for high loads. The mean shaft temperature is only significantly higher than the outlet temperature at high shaft speeds.

Predictive tool for frictional performance of piston ring-pack/liner conjunction

2019 ◽  
Vol 13 (3) ◽  
pp. 5513-5527
Author(s):  
J. W. Tee ◽  
S. H. Hamdan ◽  
W. W. F. Chong
Keyword(s):  
Film Thickness ◽  
Mathematical Models ◽  
Piston Ring ◽  
Published Data ◽  
Predictive Tool ◽  
Frictional Losses ◽  
Fundamental Understanding ◽  
Minimum Film Thickness ◽  
Piston Ring Pack ◽  
Ring Pack

Fundamental understanding of piston ring-pack lubrication is essential in reducing engine friction. This is because a substantial portion of engine frictional losses come from piston-ring assembly. Hence, this study investigates the tribological impact of different piston ring profiles towards engine in-cylinder friction. Mathematical models are derived from Reynolds equation by using Reynolds’ boundary conditions to generate the contact pressure distribution along the complete piston ring-pack/liner conjunction. The predicted minimum film thickness is then used to predict the friction generated between the piston ring-pack and the engine cylinder liner. The engine in-cylinder friction is predicted using Greenwood and Williamson’s rough surface contact model. The model considers both the boundary friction and the viscous friction components. These mathematical models are integrated to simulate the total engine in-cylinder friction originating from the studied piston ring-pack for a complete engine cycle. The predicted minimum film thickness and frictional properties from the current models are shown to correlate reasonably with the published data. Hence, the proposed mathematical approach prepares a simplistic platform in predicting frictional losses of piston ring-pack/liner conjunction, allowing for an improved fundamental understanding of the parasitic losses in an internal combustion engine.

Dynamic Analysis of Tilting-Pad Journal Bearing—Influence of Pad Deformations

1994 ◽  
Vol 116 (3) ◽  
pp. 621-627 ◽  
Author(s):  
H. Desbordes ◽  
M. Fillon ◽  
C. Chan Hew Wai ◽  
J. Frene
Keyword(s):  
Film Thickness ◽  
Pressure Field ◽  
Journal Bearing ◽  
Maximum Pressure ◽  
Tilting Pad ◽  
Minimum Film Thickness ◽  
Dimensional Finite Element ◽  
The One ◽  
Tilting Pad Journal Bearing ◽  
Tilting Pad Journal Bearings

A theoretical nonlinear analysis of tilting-pad journal bearings is presented for small and large unbalance loads under isothermal conditions. The radial displacements of internal pad surface due to pressure field are determined by a two-dimensional finite element method in order to define the actual film thickness. The influence of pad deformations on the journal orbit, on the minimum film thickness and on the maximum pressure is studied. The effects of pad displacements are to decrease the minimum film thickness and to increase the maximum pressure. The orbit amplitude is also increased by 20 percent for the large unbalance load compared to the one obtained for rigid pad.

The Effects of Oil Supply Pressure at different Groove Position on Temperature and Pressure Profile in Journal Bearing

2013 ◽  
Vol 66 (3) ◽  
Author(s):  
Mohamad Ali Ahmad ◽  
Salmiah Kasolang ◽  
R. S. Dwyer-Joyce ◽  
Aidah Jumahat
Keyword(s):  
Journal Bearing ◽  
Pressure Profile ◽  
Diameter Ratio ◽  
Radial Load ◽  
Oil Supply ◽  
Supply Pressure ◽  
Pressure Profiles ◽  
Hydrodynamic Journal Bearing ◽  
Temperature And Pressure ◽  
Length To Diameter Ratio

The effects of oil supply pressure on the temperature and pressure at different groove locations on a hydrodynamic journal bearing were investigated. A journal with a diameter of 100 mm and a ½ length-to-diameter ratio was used. The supply pressure was set to 0.2, 0.5, and 0.7 MPa at seven different groove locations, namely, -45°, -30°, -15°, 0°, +15°, +30°, and +45°. Temperature and pressure profiles were measured at speed values of 300, 500, and 800 rpm with 10 kN radial load. The results show that the change in oil supply pressure simultaneously reduced the temperature and increased the pressure profile.

Influence of Scratches on the Performance of a Partial Journal Bearing

2008 ◽  
Author(s):  
Mihai B. Dobrica ◽  
Michel Fillon
Keyword(s):  
Film Thickness ◽  
Thermal Effects ◽  
Journal Bearing ◽  
Friction Torque ◽  
Maximum Pressure ◽  
Relative Depth ◽  
Performance Loss ◽  
Minimum Film Thickness ◽  
Overall Performance ◽  
Bearing Damage

In this paper, the influence of circumferential scratches on the thermohydrodynamic performance of a partial (lobe) journal bearing is studied. The bearing damage is characterized by four factors: the area of the scratched region, the density of the scratches within the affected area, the relative position of the scratched region and the relative depth of the wear defects. The bearing performance is characterized by minimum film thickness, average oil temperature, maximum pressure, friction torque etc., at imposed magnitude and direction of the load. A numerical hydrodynamic model with global thermal effects is used for studying the influence of the different wear related parameters on the bearing performance. The results permit to predict the overall performance loss due to the circumferential wear marks, for different wear profiles. The types of wear profiles that can lead to the bearing destruction (characterized by a critical minimum film thickness) are also investigated.

The Effect of Oil Supply Pressure on the Circumferential Pressure Profile in Hydrodynamic Journal Bearing

2013 ◽  
Vol 315 ◽  
pp. 809-814 ◽  
Author(s):  
Mohamad Ali Ahmad ◽  
Salmiah Kasolang ◽  
Rob Dwyer-Joyce ◽  
Nik Rosli Abdullah
Keyword(s):  
Journal Bearing ◽  
Hydrodynamic Lubrication ◽  
Pressure Profile ◽  
Journal Bearings ◽  
Maximum Pressure ◽  
Oil Supply ◽  
Supply Pressure ◽  
Machine Elements ◽  
Hydrodynamic Journal Bearing ◽  
Circumferential Pressure

In hydrodynamic lubrication, the pressure condition of the fluid is critical to ensure good performance of the lubricated machine elements such as journal bearings. In the present study, an experimental work was conducted to determine the effect of oil supply pressure on pressure profile around the circumference of a journal bearing. A journal diameter of 100mm with a ½ length-to-diameter ratio was used. The oil supply pressure was set at three different values (0.3, 0.5, 0.7 Mpa) and the circumferential pressure results for 400, 600 and 800 RPM at different radial loads were obtained. It was observed that the maximum pressure values were affected by changes in oil supply pressure.

Sign in / Sign up

Export Citation Format

Share Document