scholarly journals Biosorptive Removal of Lead (II), Cadmium (II) and Arsenic (III) from Aqua Media on Vigna Unguiculata Leaf Powders

2018 ◽  
Vol 15 (3) ◽  
pp. 567-575
Author(s):  
K.G. Akpomie ◽  
C.C. Ezeofor ◽  
S.I. Eze ◽  
C.N. Okey ◽  
P.I. Ebiem-Kenechukwu
Keyword(s):  
Metal Ions ◽  
Vigna Unguiculata ◽  
Contact Time ◽  
Metal Ion ◽  
Low Cost ◽  
Ion Concentration ◽  
Biosorption Process ◽  
Pseudo Second Order ◽  
Best Fit ◽  
Scatchard Model

The biosorption of Cd (II), As (III) and Pb (II) ions from solution utilizing Vigna unguiculata leaf powders (VULP) as a low cost biosorbent was studied. The influence of temperature, metal ion concentration, biosorbent dose, contact time and pH on the sequestration process was examined by batch procedure. Increase in the biosorption of the three metal ions with increased pH and biosorbent dosage was obtained in this study.Equilibrium contact time of 20, 40 and 50min was achieved for Cd(II), As (III) and Pb(II) ions and biosorption was in the order As(III)> Cd(II) >Pb(II). Isotherm analysis was performed by the application of Langmuir, Freundlich, Flory-Huggins and Scatchard models. The Langmuir model gave the best fit with maximum monolayer biosorption capacity of 109.1, 105 and 119.3 mg/g for Cd (II), Pb (II) and As (III) respectively. Scatchard model confirmed a homogenous surface of VULP and monolayer biosorption of metal ions. Pseudo second order model showed the best fit compared to pseudo first order, Elovich and Banghams kinetic models according to kinetic analysis. Thermodynamics study revealed a feasibly, spontaneous exothermic biosorption process. The result showed good potentials of VULP as suitable cheap biosorbent for attenuation of Cd (II), Pb(II) and As (III) ions from polluted wastewaters.

scholarly journals Synthesis and Characterization of Piperidin-4-one Derivatives Using Green Solvent

2020 ◽  
Vol 32 (4) ◽  
pp. 727-732
Author(s):  
Harish Sharma ◽  
Rajesh Kumar ◽  
Mahesh Chandra Vishwakarma ◽  
Sushil Kumar Joshi ◽  
Narender Singh Bhandari
Keyword(s):  
Metal Ions ◽  
Contact Time ◽  
Metal Ion ◽  
Low Cost ◽  
Ion Concentration ◽  
Green Solvent ◽  
Optimum Ph ◽  
Influence Of Ph ◽  
Biosorption Equilibrium

In present study, Pyras pashia leaves were used as low cost biosorbent to study biosorption of Cu(II), Pb(II) and Cd(II) ions from contaminated wastewater. In the employed batch methods pH, contact time, metal ion concentration, temperature, biosorbent doses were taken as study parameters. The pH was varied from pH 1-9 to study the influence of pH on biosorption of metal ions by Pyras pashia. The optimum pH for the removal of Cu(II), Pb(II) and Cd(II) is observed at pH 5. The biosorption equilibrium time was varied between 15-75 min. Langmuir, Freundlich and Temkin isotherms were employed to study the biosorption. The biosorption parameter fits well with Langmuir isotherm. The biosorption of metal ions was increased with increasing biosorbent dose and contact time while increase in pH, metal ion concentration and temperature decrease the biosorption. Thermodynamic data suggest that the bisorption process was spontaneous, feasible and endothermic.

scholarly journals Sequestered capture and desorption of hexavalent chromium from solution and textile wastewater onto low cost Heinsia crinita seed coat biomass

2019 ◽  
Vol 10 (1) ◽  
Author(s):  
Folasegun A. Dawodu ◽  
Benjamin M. Akpan ◽  
Kovo G. Akpomie
Keyword(s):  
Seed Coat ◽  
Contact Time ◽  
Low Cost ◽  
Textile Wastewater ◽  
Ion Concentration ◽  
Point Of Zero Charge ◽  
Chromium Vi ◽  
Biosorption Process ◽  
Operational Variables ◽  
Pseudo Second Order

AbstractDue to the high cost associated with the treatment of effluents containing heavy metals in the environment, the continuous untreated release of effluent containing chromium from textile industries has resulted in several adverse effects to plants, ecological systems and humans. This research therefore focused on the use of a low cost, biodegradable Heinsia crinita seed coat (HCSC) material for the biosorption of chromium(VI) from aqueous and textile contaminated effluent. The biosorbent was characterized for specific surface area, surface morphology, pH point of zero charge and surface functional groups. Operational variables influences such as biosorbent dose, pH, temperature, initial Cr(VI) ion concentration and contact time on biosorption process was tested. The optimum biosorption parameter was obtained at pH 2.0, adsorbent dosage 0.25 g and contact time of 30 min. From sorption analysis, the pseudo-second-order model best described the attenuation kinetics. Concerning biosorption equilibrium, the results suggested that the adsorption isotherm obeyed the Freundlich model. Langmuir maximum monolayer biosorption capacity of 231.7 mg/g was higher than most biosorbents for Cr(VI) ion. The thermodynamic data showed a physical, spontaneous and endothermic biosorption process. HCSC showed high percentage desorption > 90% using 0.1 M HNO3 and was efficient after three cycles of regeneration studies. The results showed HCSC biomass as a suitable candidate for abstraction of Cr(VI) ion from contaminated solution and textile effluent.

scholarly journals Yam Peels as Adsorbent for the Removal of Copper (Cu) and Manganese (Mn) in Waste Water

2017 ◽  
Vol 1 (2) ◽  
pp. 230-243 ◽  
Author(s):  
E. S. Isagba ◽  
S. Kadiri ◽  
I. R. Ilaboya
Keyword(s):  
Waste Water ◽  
Experimental Data ◽  
Metal Ions ◽  
Kinetic Models ◽  
Contact Time ◽  
Metal Ion ◽  
Second Order ◽  
Ion Concentration ◽  
Order Kinetic ◽  
Pseudo Second Order

This paper investigated the use of yam peel as a natural adsorbent for the removal of Copper (Cu) and Manganese (Mn) from waste water. The yam peels were thoroughly washed with distilled water, dried, pulverized and carbonized. The carbonized yam peel was then characterized for its particle sizes, moisture content, ash content, volatile matter, Methylene Blue number, Iodine number. The raw yam peels were prepared using the same procedure, but was not carbonized. The adsorption of Mn(II) and Cu(II) ions were investigated using adsorption experiment at room temperature. The effect of contact time, metal ion concentration and dosage were evaluated. The residual concentrations of the metal ions were determined by Atomic Absorption Spectrophotometer (AAS). Experimental data obtained were analyzed using Kinetic models and Isotherms such as Pseudo- First order kinetic models, Pseudo-second order kinetic models, Langmuir isotherms and Freundlich isotherm. The analysis showed that the pseudo-second order kinetic model best described the adsorption of the metal ions; ( Cu; r2 = 0.991 for RYP and r2 = 0.834 for AYP) and (Mn; r2 = 0.958 for RYP and r2 = 0.896 for AYP) and the experimental data best fit the Freundlich model; (Cu; r2 = 0.564 for RYP and r2 = 0.871 for AYP) and (Mn; r2 = 0.685 for RYP and r2 = 0.736 for AYP). Finally, optimum removal efficiencies of 30.54% for Mn(II) and 39.62% for Cu(II) were obtained for AYP at concentrations of 50mg/l and mass dosage of 1.0g, 120 minutes contact time and a pH of 6.8.

scholarly journals The Kinetics and Thermodynamics studies of the biosorption of Chromium (III) ions from aqueous solution using groundnut husk

2018 ◽  
Vol 5 (1) ◽  
Author(s):  
Olaniyi K Yusuff ◽  
Abdulrahman A. Mukadam ◽  
Adenike M.o Abdulraheem ◽  
Aanuoluwapo Akerele
Keyword(s):  
Aqueous Solution ◽  
Particle Size ◽  
Contact Time ◽  
Low Cost ◽  
Ion Concentration ◽  
Biosorption Process ◽  
Adsorption Analysis ◽  
Effects Of Ph ◽  
Pseudo Second Order ◽  
Physical And Chemical

The biosorption of Cr (III) ions from aqueous solutions by groundnut husk, a low-cost biosorbent was studied on a laboratory scale batch experiments. The effects of pH, contact time, particle size, biosorbent dosage and temperature on the adsorption of Cr (III) ions were investigated. Determination of Chromium ion concentration in solution was done using Atomic Absorption Spectrophotometer (AAS). The results show that the removal mechanism is predominantly by chemisorption and it is dependent on the physical and chemical characteristics of the biosorbent material. From the initial concentration of 0.5 mM, optimum Cr (III) ions removal was obtained at pH of 4, particle size of 0.15 nm, contact time of 180 minutes and biosorbent dosage of 50 mg, with the highest biosorption efficiency of 81.15 %. The biosorption process was best described by the BET adsorption isotherm with R2 value 0.9814 indicating multiplayer adsorption. Analysis of the experimental data revealed that the biosorption of Cr (III) ions from aqueous solution by groundnut husk is a spontaneous process with a ?Go value of -24.38 kJmol-1 at 298 K and follow the pseudo second order kinetics with a rate constant of 0.0151 min-1. The results indicate that groundnut husk can be employed as a low cost alternative to commercial adsorbents in the removal of Cr (III) ions from wastewater.

Removal of copper(II) and cadmium(II) ions from aqueous solutions by biosorption onto pine cone

2012 ◽  
Vol 66 (3) ◽  
pp. 564-572 ◽  
Author(s):  
Görkem Değirmen ◽  
Murat Kılıç ◽  
Özge Çepelioğullar ◽  
Ayşe E. Pütün
Keyword(s):  
Aqueous Solutions ◽  
Metal Ion ◽  
Low Cost ◽  
Ion Concentration ◽  
Isotherm Models ◽  
Diffusion Kinetic ◽  
Biosorption Process ◽  
Biosorption Mechanism ◽  
Pine Cone ◽  
Pseudo Second Order

In this study, the removal of copper(II) and cadmium(II) ions from aqueous solutions by biosorption onto pine cone was studied. Variables that affect the biosorption process such as pH, biosorbent dosage, initial metal ion concentration, contact time and temperature of solution were optimized. Experimental data were fitted to Langmuir, Freundlich, Dubinin Radushkevich and Temkin isotherm models to investigate the equilibrium isotherms. Pseudo-first-order, pseudo-second-order and intraparticle diffusion kinetic models were used to determine the biosorption mechanism. The thermodynamics of biosorption were studied for predicting the nature of biosorption. Experimental results showed that pine cone could be evaluated as an alternative precursor for removal of heavy metal ions from aqueous solutions, due to its high biosorption capacity, availability, and low cost.

Use of agro-waste (Musa paradisiaca peels) as a sustainable biosorbent for toxic metal ions removal from contaminated water

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Contact Time ◽  
Metal Ion ◽  
Equilibrium Concentration ◽  
Ion Concentration ◽  
Contaminated Water ◽  
Musa Paradisiaca ◽  
Percentage Removal ◽  
Adsorbent Dose

A study of removal of heavy metal ions from heavy metal contaminated water using agro-waste was carried out with Musa paradisiaca peels as test adsorbent. The study was carried by adding known quantities of lead (II) ions and cadmium (II) ions each and respectively into specific volume of water and adding specific dose of the test adsorbent into the heavy metal ion solution, and the mixture was agitated for a specific period of time and then the concentration of the metal ion remaining in the solution was determined with Perkin Elmer Atomic absorption spectrophotometer model 2380. The effect of contact time, initial adsorbate concentration, adsorbent dose, pH and temperature were considered. From the effect of contact time results equilibrium concentration was established at 60minutes. The percentage removal of these metal ions studied, were all above 90%. Adsorption and percentage removal of Pb2+ and Cd2+ from their aqueous solutions were affected by change in initial metal ion concentration, adsorbent dose pH and temperature. Adsorption isotherm studies confirmed the adsorption of the metal ions on the test adsorbent with good mathematical fits into Langmuir and Freundlich adsorption isotherms. Regression correlation (R2) values of the isotherm plots are all positive (>0.9), which suggests too, that the adsorption fitted into the isotherms considered.

scholarly journals Batch Sorption Experiments: Langmuir and Freundlich Isotherm Studies for the Adsorption of Textile Metal Ions onto Teff Straw (Eragrostis tef) Agricultural Waste

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Mulu Berhe Desta
Keyword(s):  
Heavy Metals ◽  
Metal Ions ◽  
Contact Time ◽  
Metal Ion ◽  
Low Cost ◽  
Agricultural Waste ◽  
Equilibrium Concentration ◽  
Eragrostis Tef ◽  
Batch Adsorption ◽  
Textile Effluents

Adsorption of heavy metals (Cr, Cd, Pb, Ni, and Cu) onto Activated Teff Straw (ATS) has been studied using batch-adsorption techniques. This study was carried out to examine the adsorption capacity of the low-cost adsorbent ATS for the removal of heavy metals from textile effluents. The influence of contact time, pH, Temperature, and adsorbent dose on the adsorption process was also studied. Results revealed that adsorption rate initially increased rapidly, and the optimal removal efficiency was reached within about 1 hour. Further increase in contact time did not show significant change in equilibrium concentration; that is, the adsorption phase reached equilibrium. The adsorption isotherms could be fitted well by the Langmuir model. The value in the present investigation was less than one, indicating that the adsorption of the metal ion onto ATS is favorable. After treatment with ATS the levels of heavy metals were observed to decrease by 88% (Ni), 82.9% (Cd), 81.5% (Cu), 74.5% (Cr), and 68.9% (Pb). Results indicate that the freely abundant, locally available, low-cost adsorbent, Teff straw can be treated as economically viable for the removal of metal ions from textile effluents.

scholarly journals Removal of Zinc ions from industrial wastewater with wool fibers

2010 ◽  
Vol 7 (3) ◽  
pp. 1193-1201
Author(s):  
Baghdad Science Journal
Keyword(s):  
Acid Concentration ◽  
Contact Time ◽  
Industrial Wastewater ◽  
Metal Ion ◽  
Low Cost ◽  
Zinc Ion ◽  
Ion Concentration ◽  
Natural Material ◽  
Zinc Ions ◽  
Wool Fibers

In this research, the efficiency of low-cost unmodified wool fibers were used to remove zinc ion from industrial wastewater. Removal of zinc ion was achieved at 99.52% by using simple wool column. The experiment was carried out under varying conditions of (2h) contact time, metal ion concentration (50mg/l), wool fibers quantity to treated water (70g/l), pH(7) & acid concentration (0.05M). The aim of this method is to use a high sensitive, available & cheep natural material which applied successfully for industrial wastewater& synthetic water, where zinc ion concentration was reduced from (14.6mg/l) to (0.07mg/l) & consequently the hazardous effect of contamination was minimized.

Removal of Pb(II) and Cd(II) From Aqueous Solution by Adsorption Using Agrowaste-Modified Kaolinite Clay

2021 ◽  
Keyword(s):  
Aqueous Solution ◽  
Aqueous Solutions ◽  
Metal Ions ◽  
Metal Ion ◽  
Low Cost ◽  
Ion Concentration ◽  
Kaolinite Clay ◽  
Adsorbent Surface ◽  
Initial Adsorption ◽  
Adsorption Rates

This study showed that kaolinite clay modified with Moringa oleifera pods is a promising low cost adsorbent for the removal of metals from aqueous solution because the resultant composite has higher adsorption capacities, and hence a better metal ions removal efficiency. The efficiencies of these adsorbents for the removal of Pb (II) and Cd (II) ions from aqueous solutions were studied as a function of pH, time, adsorbate concentration and adsorbent dose. Adsorption results showed that pH did significantly affect removal of heavy metal ions between pH 3 and 6. Increasing contact time and initial metal ion concentration increased the sorption capacity of the adsorbent for the metal ions. Adsorbent dosage indicated mainly surface phenomena involving sharing of electrons between the adsorbent surface and the metal ion species. The adsorption of metal ions from aqueous solutions of both metal ions at different initial metal ion concentrations reduced the initial adsorption rates of the adsorption of Pb (II) and Cd (II) by unmodified and modified kaolinite clay.

scholarly journals Eco-Efficient Biosorbent Based on Leucaena leucocephala Residues for the Simultaneous Removal of Pb(II) and Cd(II) Ions from Water System: Sorption and Mechanism

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
C. A. Cimá-Mukul ◽  
Youness Abdellaoui ◽  
Mohamed Abatal ◽  
Joel Vargas ◽  
Arlette A. Santiago ◽  
...  
Keyword(s):  
Leucaena Leucocephala ◽  
Metal Ion ◽  
Water System ◽  
Ion Concentration ◽  
Point Of Zero Charge ◽  
Southern Mexico ◽  
Lead And Cadmium ◽  
Biosorption Process ◽  
Monolayer Adsorption ◽  
Pseudo Second Order

Leucaena leucocephala is a potential source of polyphenols widely available in southern Mexico. This work highlights the extraction of polyphenols from Leucaena leucocephala leaves waste (LLEPs) and the evaluation of their efficiency to remove the single and multicomponent Pb(II) and Cd(II) metal ions from aqueous solutions. Batch test conditions were carried out to examine the effects of contact time, initial metal ion concentration, and adsorbent dosage on the biosorption process. The surface textures and the composition of the LLEP biosorbent was characterized using pH of point of zero charge (pHPZC), attenuated total reflectance Fourier transform infrared (ATR-FTIR), and matrix-assisted laser desorption/ionization time of flight (MALDI-TOF) mass spectrometry, respectively. Further analysis using ATR-FTIR after adsorption contact of biosorbent was also investigated. The highest Langmuir saturation monolayer adsorption capacity, qm, for the removal of Pb(II) by LLEPs was obtained as 25.51 and 21.55 mg/g in mono- and bimetal solutions, respectively. The pseudo-second-order model provided the best fit for the kinetic data obtained for the removal of Pb(II), Cd(II), and their mixture, and the k2 values depend on the adsorbent mass. This implied that the chemisorption process might be the mechanism of the solute ions-LLEPs interaction in this study. Furthermore, nearly 100% removal of lead and cadmium individually and 95% of their mixture was found using 0.9 g of LLEPs.

Sign in / Sign up

Export Citation Format

Share Document