Homodyne laser vibrometer modified by an LCVR for measurement at the nanometer level

2021 ◽  
Author(s):  
Haijin Fu ◽  
Xiong Xinkang ◽  
Zheng Wang ◽  
Peng-Cheng Hu ◽  
ke wang ◽  
...  
Keyword(s):  
Laser Vibrometer

scholarly journals Application of Laser Vibrometry to Assess Defects in Ship Hull’s Welded Joints’ Technical Condition

Sensors ◽  
2021 ◽  
Vol 21 (3) ◽  
pp. 895
Author(s):  
Adam Szeleziński ◽  
Adam Muc ◽  
Lech Murawski ◽  
Marcin Kluczyk ◽  
Tomasz Muchowski
Keyword(s):  
Optical Sensors ◽  
Welded Joints ◽  
Measurement Data ◽  
Technical Condition ◽  
Laser Vibrometer ◽  
Laser Vibrometry ◽  
Destructive Testing ◽  
Laser Sensors ◽  
Measurement Methodology ◽  
The Mathematical Model

The paper presents the measurement process and test results for six thin-walled plates with different dynamic characteristics caused by different defects of welded joints. The tests were carried out using non-destructive testing (NDT). The authors made an attempt to determine the validity of the use and degree of effectiveness of the tests based on laser vibrometry in detecting defects in welded joints. The tests of welded plates were carried out using displacement laser sensors and piezoelectric accelerometers, while the source of vibration extortion was a modal hammer. In the adopted measurement methodology, the application of accelerometers was to obtain the reference data, which allowed for comparison with the measurement data obtained from the laser vibrometer. The analysis of the obtained measurement data, in the fields of time and frequency, made it possible to verify the correctness of the data obtained by means of laser vibrometry and to determine the requirements which are necessary for the correct performance of NDT tests and in the future structural health monitoring (SHM) system of welded joints with the use of a laser vibrometer. The mathematical model developed in the MSC software Pastran-Nastran was also used in the work. The model was developed for the purpose of mutual verification of the measurement and calculation tests. At the present stage of work, it can be stated that the results obtained by laser vibrometry methods should be treated as a supplement to the research conducted with traditional piezoelectric accelerometers. In certain situations, they can be used as an alternative to accelerometers, due to the fact that laser sensors do not require direct contact with the examined object. Where the object under test may be in a strong electromagnetic field, optical sensors are better suited than contact sensors.

scholarly journals Fiber Bragg Grating Sensors for Underwater Vibration Measurement: Potential Hydropower Applications

Sensors ◽  
2021 ◽  
Vol 21 (13) ◽  
pp. 4272
Author(s):  
Oscar de la Torre ◽  
Ignazio Floris ◽  
Salvador Sales ◽  
Xavier Escaler
Keyword(s):  
Fiber Bragg Grating ◽  
Numerical Models ◽  
Vibration Measurement ◽  
Quality Data ◽  
Bragg Grating ◽  
Laser Vibrometer ◽  
Main Concern ◽  
High Expectations ◽  
Fiber Bragg Grating Sensors ◽  
Hydraulic Machinery

The present paper assesses the performance and characteristics of fiber Bragg grating sensors, with a special interest in their applications in hydraulic machinery and systems. The hydropower industry is turning to this technology with high expectations of obtaining high quality data to validate and calibrate numerical models that could be used as digital twins of key assets, further strengthening the sector’s relevant position within industry 4.0. Prior to any validation, fiber Bragg grating sensors’ ability to perform well underwater for long periods of time with minimal degradation, and their ease of scalability, drew the authors´ attention. A simplified modal analysis of a partially submerged beam is proposed here as a first step to validate the potential of this type of technology for hydropower applications. Fiber Bragg grating sensors are used to obtain the beam’s natural frequencies and to damp vibrations under different conditions. The results are compared with more established waterproof electric strain gauges and a laser vibrometer with good agreement. The presence of several sensors in a single fiber ensures high spatial resolution, fundamental to precisely determine vibration patterns, which is a main concern in this industry. In this work, the beam’s vibration patterns have been successfully captured under different excitations and conditions.

Pulsed-laser vibrometer using photoelectromotive-force sensors

2003 ◽  
Vol 83 (9) ◽  
pp. 1893-1895 ◽  
Author(s):  
Ponciano Rodriguez ◽  
Sudhir Trivedi ◽  
Feng Jin ◽  
Chen-Chia Wang ◽  
Serguei Stepanov ◽  
...  
Keyword(s):  
Pulsed Laser ◽  
Force Sensors ◽  
Laser Vibrometer ◽  
Photoelectromotive Force

Investigation of Sensor Placement in Lamb Wave-Based SHM Method

2012 ◽  
Vol 518 ◽  
pp. 174-183 ◽  
Author(s):  
Pawel Malinowski ◽  
Tomasz Wandowski ◽  
Wiesław M. Ostachowicz
Keyword(s):  
Wave Propagation ◽  
Damage Detection ◽  
Guided Waves ◽  
Sensor Placement ◽  
Detection Algorithm ◽  
Piezoelectric Sensors ◽  
Optimal Placement ◽  
Laser Vibrometer ◽  
Contact Method ◽  
Monitoring Method

In this paper the investigation of a structural health monitoring method for thin-walled parts of structures is presented. The concept is based on the guided elastic wave propagation phenomena. This type of waves can be used in order to obtain information about structure condition and possibly damaged areas. Guided elastic waves can travel in the medium with relatively low attenuation, therefore they enable monitoring of extensive parts of structures. In this way it is possible to detect small defects in their early stage of growth. It is essential because undetected damage can endanger integrity of a structure. In reported investigation piezoelectric transducer was used to excite guided waves in chosen specimens. Dispersion of guided waves results in changes of velocity with the wave frequency, therefore a narrowband signal was used. Measurement of the wave field was realized using laser scanning vibrometer that registered the velocity responses at points belonging to a defined mesh. An artificial discontinuity was introduced to the specimen. The goals of the investigation was to detect it and find optimal sensor placement for this task. Determination of the optimal placement of sensors is a very challenging mission. In conducted investigation laser vibrometer was used to facilitate the task. The chosen mesh of measuring points was the basis for the investigation. The purpose was to consider various configuration of piezoelectric sensors. Instead of using vast amount of piezoelectric sensors the earlier mentioned laser vibrometer was used to gather the necessary data from wave propagation. The signals gather by this non-contact method for the considered network were input to the damage detection algorithm. Damage detection algorithm was based on a procedure that seeks in the signals the damage-reflected waves. Knowing the wave velocity in considered material the damage position can be estimated.

Research on the Piezoelectric Ultrasonic Actuator Applied to SFSS

2015 ◽  
Author(s):  
Y. J. Tang ◽  
Z. Yang ◽  
X. J. Wang ◽  
J. Wang
Keyword(s):  
Natural Vibration ◽  
Structural Parameters ◽  
Laser Vibrometer ◽  
Vibration Modes ◽  
Element Analysis ◽  
Linear Type ◽  
Frequency Sweep ◽  
The Finite Element Analysis ◽  
Frequency Sweep Test ◽  
Overall Performance

This paper presents an investigation of a novel linear-type piezoelectric ultrasonic actuator for application in a Smart Fuze Safety System (SFSS). Based on the requirements of SFSS, the structural parameters of the proposed piezoelectric ultrasonic actuator are determined by fuze arming mode. Moreover, sensitivity analysis of the structural parameters to the frequency consistency is conducted using FEM software, after which the optimal dimensions are obtained with two close natural vibration frequencies. To validate the results of FEM, the frequency sweep tests of the piezoelectric ultrasonic actuator are performed to determine the motor’s actual working mode frequencies with PSV-300-B Doppler laser vibrometer system. Furthermore, the results of frequency sweep test are compared with that of the finite element analysis, and further verified by impedance analyzer. To investigate the overall performance of the piezoelectric ultrasonic actuator, vibration modes of actuator’s stator, output speed and force of the piezoelectric ultrasonic actuator are tested. The experimental results show that the output speed and force of the actuator can reach 88.2 mm/s and 2.3N respectively, which means that piezoelectric ultrasonic actuator designed in this paper can meet the demands of the SFSS.

Percussion signals of Lygus rugulipennis Poppius (Heteroptera: Miridae)

2014 ◽  
Vol 9 (5) ◽  
pp. 543-549
Author(s):  
Sándor Koczor ◽  
Andrej Cokl
Keyword(s):  
Dominant Frequency ◽  
Laser Vibrometer ◽  
Pest Species ◽  
Adult Males ◽  
Tarnished Plant Bug ◽  
Lygus Rugulipennis ◽  
Important Pest ◽  
Low Pass ◽  
Males And Females ◽  
Study Laboratory

AbstractThe European tarnished plant bug (Lygus rugulipennis Poppius) is among the most serious pests in the family Miridae, and therefore there is increasing interest in understanding the behaviour of this species. In the present study, laboratory recordings were taken using a laser vibrometer on adult males and females to ascertain whether acoustic signals are involved in intraspecific communication. Recordings were both carried out on plant and loudspeaker membrane substrates. Males and females emitted vibratory signals and the present results indicate that these signals are important during courtship. The basic signal characteristics measured were the dominant frequency, pulse duration, repetition time and number of pulses per group within the signal. Male and female signals did not differ in respect to any of these characteristics. Plant recorded signals were longer because of different mechanical properties of substrates. Additionally, the high frequency components were attenuated due to the low-pass filtering properties of plants. As this is the first study on vibratory communication of the European tarnished plant bug, we believe these findings may contribute considerably to the better understanding of the mating behavior of this important pest species.

A Creative Vibration Energy Harvesting System to Support a Self-Powered Internet of Thing (IoT) Network in Smart Bridge Monitoring

2020 ◽  
Author(s):  
Saman Farhangdoust ◽  
Claudia Mederos ◽  
Behrouz Farkiani ◽  
Armin Mehrabi ◽  
Hossein Taheri ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Cantilever Beam ◽  
Average Power ◽  
Electrical Energy ◽  
Laser Vibrometer ◽  
Stay Cable ◽  
Fe Modelling ◽  
Vibration Energy Harvesting ◽  
Piezoelectric Energy ◽  
Energy Harvesting System

Abstract This paper presents a creative energy harvesting system using a bimorph piezoelectric cantilever-beam to power wireless sensors in an IoT network for the Sunshine Skyway Bridge. The bimorph piezoelectric energy harvester (BPEH) comprises a cantilever beam as a substrate sandwiched between two piezoelectric layers to remarkably harness ambient vibrations of an inclined stay cable and convert them into electrical energy when the cable is subjected to a harmonic acceleration. To investigate and design the bridge energy harvesting system, a field measurement was required for collecting cable vibration data. The results of a non-contact laser vibrometer is used to remotely measure the dynamic characteristics of the inclined cables. A finite element study is employed to simulate a 3-D model of the proposed BPEH by COMSOL Multiphasics. The FE modelling results showed that the average power generated by the BPEH excited by a harmonic acceleration of 1 m/s2 at 1 Hz is up to 614 μW which satisfies the minimum electric power required for the sensor node in the proposed IoT network. In this research a LoRaWAN architecture is also developed to utilize the BPEH as a sustainable and sufficient power resource for an IoT platform which uses wireless sensor networks installed on the bridge stay cables to collect and remotely transfer bridge health monitoring data over the bridge in a low-power manner.

Sign in / Sign up

Export Citation Format

Share Document