A Creative Vibration Energy Harvesting System to Support a Self-Powered Internet of Thing (IoT) Network in Smart Bridge Monitoring

2020 ◽  
Author(s):  
Saman Farhangdoust ◽  
Claudia Mederos ◽  
Behrouz Farkiani ◽  
Armin Mehrabi ◽  
Hossein Taheri ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Cantilever Beam ◽  
Average Power ◽  
Electrical Energy ◽  
Laser Vibrometer ◽  
Stay Cable ◽  
Fe Modelling ◽  
Vibration Energy Harvesting ◽  
Piezoelectric Energy ◽  
Energy Harvesting System

Abstract This paper presents a creative energy harvesting system using a bimorph piezoelectric cantilever-beam to power wireless sensors in an IoT network for the Sunshine Skyway Bridge. The bimorph piezoelectric energy harvester (BPEH) comprises a cantilever beam as a substrate sandwiched between two piezoelectric layers to remarkably harness ambient vibrations of an inclined stay cable and convert them into electrical energy when the cable is subjected to a harmonic acceleration. To investigate and design the bridge energy harvesting system, a field measurement was required for collecting cable vibration data. The results of a non-contact laser vibrometer is used to remotely measure the dynamic characteristics of the inclined cables. A finite element study is employed to simulate a 3-D model of the proposed BPEH by COMSOL Multiphasics. The FE modelling results showed that the average power generated by the BPEH excited by a harmonic acceleration of 1 m/s2 at 1 Hz is up to 614 μW which satisfies the minimum electric power required for the sensor node in the proposed IoT network. In this research a LoRaWAN architecture is also developed to utilize the BPEH as a sustainable and sufficient power resource for an IoT platform which uses wireless sensor networks installed on the bridge stay cables to collect and remotely transfer bridge health monitoring data over the bridge in a low-power manner.

Multimodal Energy Harvesting System: Piezoelectric and Electromagnetic

2008 ◽  
Vol 20 (5) ◽  
pp. 625-632 ◽  
Author(s):  
Yonas Tadesse ◽  
Shujun Zhang ◽  
Shashank Priya
Keyword(s):  
Energy Harvesting ◽  
Resonance Frequency ◽  
Permanent Magnet ◽  
Cantilever Beam ◽  
Piezoelectric Energy Harvesting ◽  
Prototype System ◽  
Finite Element Software ◽  
Piezoelectric Energy ◽  
Energy Harvesting System ◽  
Tip Mass

In this study, we report a multimodal energy harvesting device that combines electromagnetic and piezoelectric energy harvesting mechanism. The device consists of piezoelectric crystals bonded to a cantilever beam. The tip of the cantilever beam has an attached permanent magnet which, oscillates within a stationary coil fixed to the top of the package. The permanent magnet serves two purpose (i) acts as a tip mass for the cantilever beam and lowers the resonance frequency, and (ii) acts as a core which oscillates between the inductive coils resulting in electric current generation through Faraday's effect. Thus, this design combines the energy harvesting from two different mechanisms, piezoelectric and electromagnetic, on the same platform. The prototype system was optimized using the finite element software, ANSYS, to find the resonance frequency and stress distribution. The power generated from the fabricated prototype was found to be 0.25 W using the electromagnetic mechanism and 0.25 mW using the piezoelectric mechanism at 35 g acceleration and 20 Hz frequency.

scholarly journals Analysis of Double Elastic Steel Wind Driven Magneto-Electric Vibration Energy Harvesting System

Sensors ◽  
2021 ◽  
Vol 21 (21) ◽  
pp. 7364
Author(s):  
Yi-Ren Wang ◽  
Ming-Ching Chu
Keyword(s):  
Energy Harvesting ◽  
Electric Energy ◽  
Elastic Beam ◽  
Electrical Energy ◽  
Vibration Energy ◽  
Vibration Energy Harvesting ◽  
Concentrated Load ◽  
Single Beam ◽  
Piezoelectric Patch ◽  
Energy Harvesting System

This research proposes an energy harvesting system that collects the downward airflow from a helicopter or a multi-axis unmanned rotary-wing aircraft and uses this wind force to drive the magnet to rotate, generating repulsive force, which causes the double elastic steel system to slap each other and vibrate periodically in order to generate more electricity than the traditional energy harvesting system. The design concept of the vibration mechanism in this study is to allow the elastic steel carrying the magnet to slap another elastic steel carrying the piezoelectric patch to form a set of double elastic steel vibration energy harvesting (DES VEH) systems. The theoretical DES VEH mechanism of this research is composed of a pair of cantilever beams, with magnets attached to the free end of one beam, and PZT attached to the other beam. This study analyzes the single beam system first. The MOMS method is applied to analyze the frequency response of this nonlinear system theoretically, then combines the piezoelectric patch and the magneto-electric coupling device with this nonlinear elastic beam to analyze the benefits of the system’s converted electrical energy. In the theoretical study of the DES VEH system, the slapping force between the two elastic beams was considered as a concentrated load on each of the beams. Furthermore, both SES and DES VEH systems are studied and correlated. Finally, the experimental data and theoretical results are compared to verify the feasibility and correctness of the theory. It is proven that this DES VEH system can not only obtain the electric energy from the traditional SES VEH system but also obtain the extra electric energy of the steel vibration subjected to the slapping force, which generates optimal power to the greatest extent.

Design of piezoelectric energy harvesting system using cantilever beam

2014 ◽  
Vol 135 (4) ◽  
pp. 2218-2219
Author(s):  
Jin-Su Kim ◽  
Un-Chang Jeong ◽  
Sun-Hoon Lee ◽  
Jung-Min Jeong ◽  
Jae-Eung Oh
Keyword(s):  
Energy Harvesting ◽  
Cantilever Beam ◽  
Piezoelectric Energy Harvesting ◽  
Piezoelectric Energy ◽  
Energy Harvesting System

scholarly journals Maximum Obtainable Energy Harvesting Power from Galloping-Based Piezoelectrics

2020 ◽  
Vol 2020 ◽  
pp. 1-8
Author(s):  
Mohammad Yaghoub Abdollahzadeh Jamalabadi ◽  
Mostafa Safdari Shadloo ◽  
Arash Karimipour
Keyword(s):  
Energy Harvesting ◽  
Cantilever Beam ◽  
Bluff Body ◽  
Mechanical Energy ◽  
Average Power ◽  
Electrical Energy ◽  
Load Resistance ◽  
Nonlinear Motion ◽  
Rc Circuit ◽  
Deflection Limit

In this paper, the maximum obtainable energy from a galloping cantilever beam is found. The system consists of a bluff body in front of wind which was mounted on a cantilever beam and supported by piezoelectric sheets. Wind energy caused the transverse vibration of the beam and the mechanical energy of vibration is transferred to electrical charge by use of piezoelectric transducer. The nonlinear motion of the Euler–Bernoulli beam and conservation of electrical energy is modeled by lumped ordinary differential equations. The wind forces on the bluff body are modeled by quasisteady aeroelasticity approximation where the fluid and solid corresponding dynamics are disconnected in time scales. The linearized motion of beam is limited by its yield stress which causes to find a limit on energy harvesting of the system. The theory founded is used to check the validity of previous results of researchers for the effect of wind speed, tip cross-section geometry, and electrical load resistance on onset speed to galloping, tip displacement, and harvested power. Finally, maximum obtainable average power in a standard RC circuit as a function of deflection limit and synchronized charge extraction is obtained.

scholarly journals Intelligent Control of Vibration Energy Harvesting System

2020 ◽  
Vol 16 (1) ◽  
pp. 1-10
Author(s):  
Nizar Almajdy ◽  
Rabee Thjel ◽  
Ramzi Ali
Keyword(s):  
Energy Harvesting ◽  
Intelligent Control ◽  
Fuzzy Logic Controller ◽  
Mechanical Vibration ◽  
Electrical Energy ◽  
Operating Conditions ◽  
Vibration Energy ◽  
Vibration Energy Harvesting ◽  
Simulink Model ◽  
Energy Harvesting System

The Intelligent Control of Vibration Energy Harvesting system is presented in this paper. The harvesting systems use a mechanical vibration to generate electrical energy in a suitable form for use. Proportional-Integrated-derivative controller and Fuzzy Logic controller have been suggested; their parameters are optimized using a new heuristic algorithm, the Camel Traveling Algorithm(CTA). The proposed circuit Simulink model was constructed in Matlab facilities, and the model was tested under various operating conditions. The results of the simulation using the CTA was compared with two other methods.

scholarly journals Development of Micro-Mobility Based on Piezoelectric Energy Harvesting for Smart City Applications

2020 ◽  
Vol 12 (7) ◽  
pp. 2933 ◽  
Author(s):  
Chaiyan Jettanasen ◽  
Panapong Songsukthawan ◽  
Atthapol Ngaopitakkul
Keyword(s):  
Energy Source ◽  
Energy Harvesting ◽  
Smart City ◽  
Alternative Energy ◽  
Mechanical Energy ◽  
Electrical Energy ◽  
Piezoelectric Energy Harvesting ◽  
Alternative Energy Source ◽  
Piezoelectric Energy ◽  
Energy Harvesting System

This study investigates the use of an alternative energy source in the production of electric energy to meet the increasing energy requirements, encourage the use of clean energy, and thus reduce the effects of global warming. The alternative energy source used is a mechanical energy by piezoelectric material, which can convert mechanical energy into electrical energy, that can convert mechanical energy from pressure forces and vibrations during activities such as walking and traveling into electrical energy. Herein, a pilot device is designed, involving the modification of a bicycle into a stationary exercise bike with a piezoelectric generator, to study energy conversion and storage generated from using the bike. Secondly, the piezoelectric energy harvesting system is used on bicycles as a micro-mobility, light electric utility vehicle with smart operation, providing a novel approach to smart city design. The results show that the energy harvested from the piezoelectric devices can be stored in a 3200 mAh, 5 V battery and power sensors on the bicycle. Moreover, 13.6 mW power can be generated at regular cycling speed, outputting 11.5 V and 1.2 mA. Therefore, the piezoelectric energy harvesting system has sufficient potential for application as a renewable energy source that can be used with low power equipment.

scholarly journals Characterization of Polyvinylidene Difluoride-based Energy Harvesting with IDE Circuit Flexible Cantilever Beam

2022 ◽  
Vol 30 (1) ◽  
pp. 605-619
Author(s):  
Khairul Azman Ahmad ◽  
Noramalina Abdullah ◽  
Mohamad Faizal Abd Rahman ◽  
Muhammad Khusairi Osman ◽  
Rozan Boudville
Keyword(s):  
Energy Harvesting ◽  
Piezoelectric Material ◽  
Cantilever Beam ◽  
Energy Harvester ◽  
Electrical Energy ◽  
Adhesive Tape ◽  
Induced Voltage ◽  
Interdigitated Electrode ◽  
Polyvinylidene Difluoride ◽  
Piezoelectric Energy

Piezoelectric energy harvesting is the process of extracting electrical energy using energy harvester devices. Any stress in the piezoelectric material will generate induced voltage. Previous energy harvester device with stiff cantilever beam was generated low harvested energy. A flexural piezoelectric energy harvester is proposed to improve the generated harvesting energy. Polyvinylidene difluoride is a polymer piezoelectric material attached to a flexible circuit made of polyimide. Four interdigitated electrode circuits were designed and outsourced for fabrication. The polyvinylidene difluoride was then attached to the interdigitated electrode circuit, and a single clear adhesive tape was used to bind them. Four piezoelectric energy harvesters and ultrasonic ceramic generators were experimentally tested using a sieve shaker. The sieve shaker contains a two-speed oscillator, with M1=0.025 m/s and M2=0.05 m/s. It was used to oscillate the energy harvester devices. The resulting induced voltages were then measured. Design 4, with the widest width of electrode fingers and the widest gap between electrode fingers, had the highest power generated at an output load of 0.745 µW with the M2 oscillation speed. The oscillation speed of the sieve shaker impacted the energy harvester devices as a higher oscillation speed gave higher generated power.

The benefits of a magnetically coupled asymmetric monostable dual-cantilever energy harvester under random excitation

2019 ◽  
Vol 30 (20) ◽  
pp. 3136-3145 ◽  
Author(s):  
Zhengqiu Xie ◽  
Shengxi Zhou ◽  
Jitao Xiong ◽  
Wenbin Huang
Keyword(s):  
Energy Harvesting ◽  
Cantilever Beam ◽  
Energy Harvester ◽  
Mechanical Strain ◽  
Magnetic Coupling ◽  
Random Excitation ◽  
Superior Performance ◽  
Vibration Energy ◽  
Vibration Energy Harvesting ◽  
Piezoelectric Energy

Piezoelectric vibration energy harvesting is a promising technique to power wireless sensor networks. This article originally presents a magnetically coupled asymmetric monostable dual-cantilever piezoelectric energy harvester consisting of a generating piezoelectric cantilever beam and an auxiliary cantilever beam. Theoretical and experimental results both verify that the asymmetric harvester has the superior performance compared with the conventional magnetically coupled symmetric bistable dual-cantilever piezoelectric energy harvester, yielding higher voltage output under different magnetic coupling intensities and different power densities of the band-limited Gaussian white noise random excitation. More importantly, the mechanical strain of the asymmetric harvester is much smaller than that of the symmetric harvester, being lower than half of the latter one under strong magnetic coupling. Therefore, due to its higher energy conversion efficiency and better durability, the proposed asymmetric harvester is beneficial for practical environment vibration energy harvesting.

scholarly journals Piezoelectric Energy Harvester for IoT Sensor Devices

2021 ◽  
Vol 5 (4) ◽  
pp. 124
Author(s):  
Noor Pratama Apriyanto ◽  
Eka Firmansyah ◽  
Lesnanto Multa Putranto
Keyword(s):  
Energy Harvesting ◽  
Energy Harvester ◽  
Electrical Energy ◽  
Sensor Nodes ◽  
Energy Characteristics ◽  
Module Design ◽  
Piezoelectric Energy ◽  
Battery Power ◽  
Piezoelectric Elements ◽  
Energy Harvesting System

Limited battery power is a major challenge for wireless sensor network (WSN) in internet of things (IoT) applications, especially in hard-to-reach places that require periodic battery replacement. The energy harvesting application is intended as an alternative to maintain network lifetime by utilizing environmental energy. The proposed method utilized piezoelectricity to convert vibration or pressure energy into electrical energy through a modular piezoelectric energy harvesting design used to supply energy to sensor nodes in WSN. The module design consisted of several piezoelectric elements, of which each had a different character in generating energy. A bridge diode was connected to each element to reduce the feedback effect of other elements when pressure was exerted. The energy produced by the piezoelectric is an impulse so that the capacitor was used to quickly store the energy. The proposed module produced 7.436 μJ for each step and 297.4 μJ of total energy with pressure of a 45 kg load 40 times with specific experiments installed under each step. The energy could supply WSN nodes in IoT application with a simple energy harvesting system. This paper presents a procedure for measuring the energy harvested from a commonly available piezoelectric buzzer. The specific configurations of the piezoelectric and the experiment setups will be explained. Therefore, the output energy characteristics will be understood. In the end, the potentially harvested energy can be estimated. Therefore, the configuration of IoT WSN could be planned.

Sign in / Sign up

Export Citation Format

Share Document