scholarly journals Study of Green and Chemical Methods for Synthesis of Nano Spinel MgFe2O4 and its Study on Degradation of Rose Bengal Dye

2020 ◽  
Vol 32 (3) ◽  
pp. 501-507
Author(s):  
Krushitha Shetty ◽  
B.S. Prathibha ◽  
Dinesh Rangappa ◽  
K.S. Anantharaju ◽  
H.P. Nagaswarupa ◽  
...  
Keyword(s):  
Combustion Synthesis ◽  
Rose Bengal ◽  
Sol Gel ◽  
Solution Combustion Synthesis ◽  
X Ray Diffraction ◽  
Solution Combustion ◽  
Chemical Methods ◽  
Transfer Resistance ◽  
X Ray ◽  
Rose Bengal Dye

MgFe2O4 nanoferrites were synthesized by sol-gel and solution combustion synthesis (SCS) methods through green and chemical methods. Green and chemical methods for sol-gel were processed with use of lemon extract and citric acid, respectively. A green and chemical method for solution combustion synthesis was followed by using Phyllanthus acidus leaf extract and urea, respectively. The influence of synthesis approach on the behaviour of prepared nanoferrites were studied using powder X-ray diffraction (PXRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM) and UV visible spectroscopy, vast variation in particle size, crystallinity, electrochemical and photocatalytic activity of the nanoferrites synthesized by various methods were witnessed. Powder X-ray diffraction (PXRD) result of prepared nanoferrites acquired by green and chemical approaches clarified phase structure as spinel and the crystalline size found to be around 11-24 nm. The spinel surface morphology was witnessed for the synthesized nanoferrites. The tetrahedral and octahedral sites of the prepared nanoferrites were confirmed by FTIR spectra. MgFe2O4 nanoferrites synthesized by green sol-gel approach exposed superior electrochemical activity by possessing very less charge transfer resistance. The results of EIS were correlated with the photocatalytic degradation of Rose Bengal dye. Photocatalytic property of the prepared nanoferrites was examined for photodegradation of Rose Bengal dye under UV-light.

Microwave-Assisted Solution Combustion Synthesis and Characterization of Thermoelectric Ca3Co2O6 Powders

2013 ◽  
Vol 802 ◽  
pp. 84-88
Author(s):  
Sagulthai Kahatta ◽  
Nopsiri Chaiyo ◽  
Chesta Ruttanapun ◽  
Wicharn Techitdheera ◽  
Wisanu Pecharapa ◽  
...  
Keyword(s):  
Combustion Synthesis ◽  
Solution Combustion Synthesis ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Solution Combustion ◽  
X Ray ◽  
Microwave Assisted ◽  
Product Characterization ◽  
Rhombohedral Crystal Structure ◽  
Rhombohedral Crystal

The microwave-assisted solution combustion synthesis was applied to the initial synthesizing of Ca3Co2O6powder using glycine as a fuel and nitrate as an oxidant. The as-synthesized powders were calcined at 700-1,000ºC for 4h. Product characterization was performed using Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and Scanning electron microscope (SEM). The fuel-to-oxidizer molar ratio was found to affect the combustion reaction and character of the powder obtained. The phase composition of powder after calcination at various temperatures has shown that the formation of Ca3Co2O6occurs directly. The calcined powder possesses a rhombohedral crystal structure with an X-ray diffraction pattern that could be matched with the Ca3Co2O6JCPDS: 89-0629. This method is a simple way of synthesizing fine Ca3Co2O6powder with a low calcination temperature.

LiAl0.1Mn1.9O4 Prepared by a Solution Combustion Synthesis Using Acetate as Raw Materials and Acetic Acid as Fuel: Effect of Further Calcination Time

2012 ◽  
Vol 485 ◽  
pp. 473-477
Author(s):  
Gui Yang Liu ◽  
Jun Ming Guo ◽  
Li Li Zhang ◽  
Jing Wang ◽  
Bao Sen Wang ◽  
...  
Keyword(s):  
Combustion Synthesis ◽  
Raw Materials ◽  
Synthesis Method ◽  
Solution Combustion Synthesis ◽  
Metal Foil ◽  
X Ray Diffraction ◽  
Calcination Time ◽  
Solution Combustion ◽  
X Ray ◽  
Discharge Capacities

LiAl0.1Mn1.9O4 materials were prepared by a solution combustion synthesis method. In order to improve the purity of the products, the effect of further calcination time was investigated. The phase compositions of the as-prepared products were determined by X-ray diffraction (XRD). The electrochemical performance of the products was tested by using a coin-type half battery versus lithium metal foil as anode material. XRD results suggested that the main phase of the products was LiAl0.1Mn1.9O4, and there was a trace amount Mn2O3 impurity in some of the products. The purity, crystallinity and grain size of the LiAl0.1Mn1.9O4 were increased with increasing further calcination time. Electrochemical experiments demonstrate that the initial discharge capacities of the products with further calcination time of 0, 6, 12 and 24h were 93.7, 105.7, 114.0 and 120.6mAh/g, and about 89.8, 89.5, 89.2 and 88.3% of the initial capacities were retained after 25 cycles, respectively. Further calcination time can enhance the initial capacity, but is not favorable for the cycle ability of the products.

Ni Doped LiMn2O4 Prepared by a Flameless Combustion Synthesis

2012 ◽  
Vol 625 ◽  
pp. 251-254 ◽  
Author(s):  
Gui Yang Liu ◽  
Bao Sen Wang ◽  
Ying He ◽  
Jun Ming Guo
Keyword(s):  
Combustion Synthesis ◽  
Raw Materials ◽  
Synthesis Method ◽  
Solution Combustion Synthesis ◽  
Electrochemical Performances ◽  
X Ray Diffraction ◽  
Galvanostatic Charge ◽  
Solution Combustion ◽  
Limn2o4 Spinel ◽  
X Ray

In this paper, LiNixMn2−xO4 materials were prepared by solution combustion synthesis method using acetic salts as raw materials and acetic acid as fuel. The phase structures are characterized by X-ray diffraction (XRD). Electrochemical performances of the materials are investigated by galvanostatic charge/discharge methods. XRD results revealed that the main phase of the products with increasing Ni3+ content is LiMn2O4, and there is a trace amount of Mn3O4 found in the product with Ni3+ content of 0.05. Electrochemical experiments showed that the capacity and the cyclability of the LiNixMn2−xO4 materials decrease with increasing Ni3+ content. Ni3+ doping has no significantly improvement for the capacity and the cyclability of the LiMn2O4 spinel.

Phase Structures of LiMn1.95Fe0.05O4 Prepared by Solution Combustion Synthesis and Molten-Salt Combustion Synthesis Methods

2012 ◽  
Vol 625 ◽  
pp. 255-258
Author(s):  
Gui Yang Liu ◽  
Bao Sen Wang ◽  
Ying He ◽  
Jun Ming Guo
Keyword(s):  
Combustion Synthesis ◽  
Molten Salts ◽  
Solution Combustion Synthesis ◽  
Relative Content ◽  
Synthesis Methods ◽  
X Ray Diffraction ◽  
Solution Combustion ◽  
X Ray ◽  
Phase Structures ◽  
Main Impurity

LiFe0.05Mn1.95O4 materials were prepared by molten-salts combustion synthesis and solution combustion synthesis methods, respectively. The phase structure and compositions of the products were determined by X-ray diffraction (XRD). The main phase of the products prepared by the two methods is LiMn2O4, but at 300-600oC, pure products can not be obtained. At the temperatures of 300 and 400oC, the main impurities are MnO and Mn3O4. The impurities decrease with increasing temperatures, and finally disappear at >500oC. At 500 and 600oC, the main impurity is Mn2O3, but the relative content of Mn2O3 is low.

scholarly journals Fabrication of La2O3 Uniformly Doped Mo Nanopowders by Solution Combustion Synthesis Followed by Reduction under Hydrogen

Materials ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 2385 ◽  
Author(s):  
Siyong Gu ◽  
Mingli Qin ◽  
Houan Zhang ◽  
Jidong Ma
Keyword(s):  
Combustion Synthesis ◽  
Hydrogen Reduction ◽  
Synthesis Method ◽  
Reduction Process ◽  
Solution Combustion Synthesis ◽  
Particle Sizes ◽  
X Ray Diffraction ◽  
Solution Combustion ◽  
X Ray ◽  
Transmission Electron

This work reports the preparation of La2O3 uniformly doped Mo nanopowders with the particle sizes of 40–70 nm by solution combustion synthesis and subsequent hydrogen reduction (SCSHR). To reach this aim, the foam-like MoO2 precursors (20–40 nm in size) with different amounts of La2O3 were first synthesized by a solution combustion synthesis method. Next, these precursors were used to prepare La2O3 doped Mo nanopowders through hydrogen reduction. Thus, the content of La2O3 used for doping can be accurately controlled via the SCSHR route to obtain the desired loading degree. The successful doping of La2O3 into Mo nanopowders with uniform distribution were proved by X-ray photon spectroscopy and transmission electron microscopy. The preservation of the original morphology and size of the MoO2 precursor by the La2O3 doped Mo nanopowders was attributed to the pseudomorphic transport mechanism occurring at 600 °C. As shown by X-ray diffraction, the formation of Mo2C impurity, which usually occurs in the direct H2 reduction process, can be avoided by using the Ar calcination-H2 reduction process, when residual carbon is removed by the carbothermal reaction during Ar calcination at 500 °C.

Obtainment of α-Tricalcium Phosphate by Solution Combustion Synthesis Method Using Urea as Combustible

2008 ◽  
Vol 396-398 ◽  
pp. 591-594 ◽  
Author(s):  
Tiago M. Volkmer ◽  
L.L. Bastos ◽  
V.C. Sousa ◽  
L.A. Santos
Keyword(s):  
Heat Treatment ◽  
Combustion Synthesis ◽  
Tricalcium Phosphate ◽  
Synthesis Method ◽  
Solution Combustion Synthesis ◽  
Stoichiometric Ratio ◽  
X Ray Diffraction ◽  
Solution Combustion ◽  
Ph Adjustment ◽  
X Ray

The aim of this work is the synthesis of α-tricalcium phosphate by solution combustion synthesis using urea as combustible in the stoichiometric ratio and with excess of combustible. The salts Ca(O3)2.4H2O and (H4)2HPO4 were used as reaction precursors with Ca/P ratio of 1.5. The pH adjustment was made adding nitric acid. A porous foam composed by β-tricalcium phosphate, hydroxyapatite and α or β-dicalcium pyrophosphate were obtained as reaction product. X-ray diffraction was used to identify the phases. The obtainment of α-TCP was possible after a heat treatment where the material was held at 1250°C for 15 hours followed by quenching. Smaller particle size was obtained when four times the stoichiometric ratio of combustible was used in the reaction. α-TCP samples were immersed in SBF in order to verify the biocompatibility.

scholarly journals The Effect of the Precursor Solution’s Pretreatment on the Properties and Microstructure of the SCS Final Nanomaterials

2019 ◽  
Vol 9 (6) ◽  
pp. 1200 ◽  
Author(s):  
Olga Thoda ◽  
Galina Xanthopoulou ◽  
George Vekinis ◽  
Alexander Chroneos
Keyword(s):  
Combustion Synthesis ◽  
High Speed ◽  
Solution Combustion Synthesis ◽  
Precursor Solution ◽  
Processing Parameters ◽  
Catalytic Performance ◽  
X Ray Diffraction ◽  
Solution Combustion ◽  
X Ray ◽  
Powder Properties

Nanostructured nickel-based catalysts were produced by solution combustion synthesis and it was found that their properties and structure depended on the pretreatment of the precursor solution. X-ray diffraction, N2 adsorption, and an infrared high-speed camera were used to follow the various synthesis steps and to characterize the obtained catalysts, while their catalytic activity was determined in the hydrogenation of maleic acid. It was determined that the amount of water used and the heating of the precursor solution under mild stirring up to 70 °C influenced the nickel nitrate–glycine–water complexes that were formed in the precursor solution in the form of dendrites. These play a key role in the solution combustion synthesis (SCS) reaction mechanism and in particular in the formation of nickel-based catalysts. Understanding the interrelationships between the processing parameters and the ensuing powder properties allowed an efficient optimization of the catalytic performance.

A Contrastive Study on LiMn2O4 Prepared by Solution Combustion Synthesis Using Nitrate or Acetate Salts as Raw Materials

2011 ◽  
Vol 142 ◽  
pp. 205-208 ◽  
Author(s):  
Gui Yang Liu ◽  
Jun Ming Guo ◽  
Li Li Zhang ◽  
Bao Sen Wang ◽  
Ying He
Keyword(s):  
Acetic Acid ◽  
Combustion Synthesis ◽  
Raw Materials ◽  
Solution Combustion Synthesis ◽  
Electrochemical Performances ◽  
X Ray Diffraction ◽  
Solution Combustion ◽  
X Ray ◽  
Contrastive Study ◽  
Nitrate Salts

In this paper, spinel LiMn2O4 was prepared by the solution combustion synthesis using acetate or nitrate salts as raw materials and acetic acid as fuel. The composition and phase structure are determined by X-ray diffraction (XRD) and the electrochemical performance is tested by using a coin type half-battery versus Li+/Li. The results indicate that the products prepared from acetate salts have higher purities, higher crystallinities and better electrochemical performances than these of the products prepared from nitrate salts. And for the products prepared from acetate salts, the performance becomes worse with increasing acetic acid ratios. Contrarily, for the products prepared from nitrate salts, the performance becomes little better with increasing acetic acid ratios.

Al Doped LiMn2O4 Prepared by a Solution Combustion Synthesis Using Acetate Salts as Raw Materials and Acetic Acid as Fuel

2011 ◽  
Vol 142 ◽  
pp. 209-212
Author(s):  
Gui Yang Liu ◽  
Jun Ming Guo ◽  
Li Li Zhang ◽  
Bao Sen Wang ◽  
Ying He
Keyword(s):  
Acetic Acid ◽  
Combustion Synthesis ◽  
Raw Materials ◽  
Synthesis Method ◽  
Solution Combustion Synthesis ◽  
Electrochemical Performances ◽  
X Ray Diffraction ◽  
Solution Combustion ◽  
X Ray ◽  
Charge Discharge

To improve the cyclability of spinel LiMn2O4, Al3+doped LiAlxMn2−xO4(x=0, 0.01, 0.05 and 0.10) materials are prepared using a solution combustion synthesis method using acetic salts as raw materials and acetic acid as fuel. Their phase structures are characterized by X-ray diffraction (XRD). Electrochemical performances of the materials are investigated by galvanostatic charge/discharge methods. XRD results reveal that the purity of the samples increases with increasing Al3+content. Electrochemical experiments demonstrate that the charge/discharge cyclability of the LiAlxMn2-xO4increases with increasing Al3+content. Compared with the pristine LiMn2O4, the Al-doped LiAlxMn1−xO4show the obviously improved cyclability, especially for the sample LiAl0.1Mn1.9O4.

Flameless Solution Combustion Synthesis of Al3+ Doped LiMn2O4

2011 ◽  
Vol 186 ◽  
pp. 7-10 ◽  
Author(s):  
Gui Yang Liu ◽  
Jun Ming Guo ◽  
Bao Sen Wang ◽  
Ying He
Keyword(s):  
Combustion Synthesis ◽  
Synthesis Method ◽  
Solution Combustion Synthesis ◽  
Xrd Analysis ◽  
Cycling Performance ◽  
X Ray Diffraction ◽  
Solution Combustion ◽  
Electrochemical Test ◽  
Micro Morphology ◽  
Better Than

Single phase Al3+ doped LiMn2O4 has been prepared by flameless solution combustion synthesis method at 600oC for 1h. X-ray diffraction (XRD) and scanning electric microscope (SEM) were used to determine the phase composition and micro morphology of the products. XRD analysis indicates that the purities increase and the lattice parameters of the products decrease with increasing Al3+ content. Electrochemical test indicates that the cycling performance of the products with Al3+ doping are better than that of the product without Al3+ doping. The product LiAl0.10Mn1.90O4 gets the best electrochemical performance. At the current density of 30mA/g, the initial discharge capacity of LiAl0.10Mn1.90O4 is 124.8mAh/g, and after 20 cycles, the capacity retention is more than 89%. SEM investigation indicates that the particles of LiAl0.10Mn1.90O4 are sub-micron in size and well dispersed.

Sign in / Sign up

Export Citation Format

Share Document