scholarly journals Performance Evaluation of a Prototype Solar Collector Using Convex Lenses for Varying Mass Flow Rate of the Heat Transfer Fluid

2015 ◽  
Vol 2 (7) ◽  
pp. 40-43
Author(s):  
Pramod Kumar Trivedi ◽  
Jitendra Jayant ◽  
Kamal Kant Vashistha ◽  
Tiwari A C
Keyword(s):  
Heat Transfer ◽  
Performance Evaluation ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Solar Collector ◽  
Heat Transfer Fluid ◽  
Varying Mass

Thermodynamic Performance Evaluation of a Solar Parabolic Dish Assisted Multigeneration System

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Muhammad Abid ◽  
Muhammad Sajid Khan ◽  
Tahir Abdul Hussain Ratlamwala
Keyword(s):  
Heat Transfer ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Solar Collector ◽  
Integrated System ◽  
Heat Transfer Fluid ◽  
Outlet Temperature ◽  
Parabolic Dish ◽  
Single Effect

The concentration ratio of the parabolic dish solar collector (PDSC) is considered to be one of the highest among the concentrated solar power technologies (CSPs); therefore, such system is capable of generating more heat rate. The present paper focuses on the integration of the PDSC with the combined cycle (gas cycle as the toping cycle and steam cycle as the bottoming cycle) along with the utilization of waste heat from the power cycle to drive the single effect lithium bromide/water absorption cycle. Molten salt is used as a heat transfer fluid in the solar collector. The engineering equation solver (EES) is employed for the mathematical modeling and simulation of the solar integrated system. The various operating parameters (beam radiation, inlet and ambient temperatures of heat transfer fluid, mass flow rate of heat transfer fluid, evaporator temperature, and generator temperature) are varied to analyze their influence on the performance parameters (power output, overall energetic and exergetic efficiencies, outlet temperature of the receiver, and as coefficient of performance (COP) and exergy efficiencies) of the integrated system. The results show that the overall energy and exergy efficiencies are observed to be 39.9% and 42.95% at ambient temperature of 27 °C and solar irradiance of 1000 W/m2. The outlet temperature of the receiver is noticed to decrease from 1008 K to 528 K for an increase in the mass flow rate from 0.01 to 0.05 kg/s. The efficiency rate of the power plant is 38%, whereas COP of single effect absorption system is 0.84, and it will decrease from 0.87 to 0.79. However, the evaporator load is decreased to approximately 9.7% by increasing the generator temperature from 47 °C to 107 °C.

Exergy-Based Optimization of Sub- and Supercritical Thermal Energy Storage Systems

2014 ◽  
Author(s):  
Louis A. Tse ◽  
Reza Baghaei Lakeh ◽  
Richard E. Wirz ◽  
Adrienne S. Lavine
Keyword(s):  
Heat Transfer ◽  
Energy Storage ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Energy ◽  
Thermal Energy Storage ◽  
Storage System ◽  
Heat Transfer Fluid ◽  
Energy And Exergy

In this work, energy and exergy analyses are applied to a thermal energy storage system employing a storage medium in the two-phase or supercritical regime. First, a numerical model is developed to investigate the transient thermodynamic and heat transfer characteristics of the storage system by coupling conservation of energy with an equation of state to model the spatial and temporal variations in fluid properties during the entire working cycle of the TES tank. Second, parametric studies are conducted to determine the impact of key variables (such as heat transfer fluid mass flow rate and maximum storage temperature) on both energy and exergy efficiencies. The optimum heat transfer fluid mass flow rate during charging must balance exergy destroyed due to heat transfer and exergy destroyed due to pressure losses, which have competing effects. Similarly, the optimum maximum storage fluid temperature is evaluated to optimize exergetic efficiency. By incorporating exergy-based optimization alongside traditional energy analyses, the results of this study evaluate the optimal values for key parameters in the design and operation of TES systems, as well as highlight opportunities to minimize thermodynamic losses.

Influence of Dimensionless Parameter on De-Ionized Water-alumina Nanofluid Based Parabolic Trough Solar Collector

2020 ◽  
Vol 13 (3) ◽  
pp. 206-221
Author(s):  
Vijayan Gopalsamy ◽  
Karunakaran Rajasekaran ◽  
Logesh Kamaraj ◽  
Siva Sivasaravanan ◽  
Metin Kok
Keyword(s):  
Heat Transfer ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Solar Collector ◽  
Dimensionless Parameter ◽  
Parabolic Trough ◽  
Alumina Nanofluid ◽  
Parabolic Trough Solar Collector

Background: Aqueous-alumina nanofluid was prepared using magnetic stirrer and ultrasonication process. Then, the prepared nanofluid was subjected to flow through the unshielded receiver of the parabolic trough solar collector to investigate the performance of the nanofluid and the effects of the dimensionless parameter were determined. Methods: The experimental work has been divided into two sections. First, the nanofluid was prepared and tested for its morphology, dimensions, and sedimentation using X-Ray Diffraction and Raman shift method. Then, the nanofluids of various concentrations from 0 to 4.0% are used as heat transfer fluid in unshielded type collector. Finally, the effect of the dimensionless parameter on the performance was determined. Results: For the whole test period, depending upon the bulk mean temperature, the dimensionless parameters such as Re and Nu varied from 1098 to 4552 & 19.30 to 46.40 for air and 2150 to 7551 & 11.11 to 48.54 for nanofluid. The enhancement of thermal efficiency found for 0% and 4.0% nanoparticle concentrations was 32.84% for the mass flow rate of 0.02 kg/s and 13.26% for the mass flow rate of 0.06 kg/s. Conclusion: Re and Nu of air depend on air velocity and ambient temperature. Re increased with the mass flow rate and decreased with concentration. Heat loss occurred by convection mode of heat transfer. Heat transfer coefficient and global efficiency increased with increased mass flow rate and volume fraction. The thermal efficiency of both 0% and 4.0% concentrations became equal for increased mass flow rate. It has been proven that at high mass flow rates, the time available to absorb the heat energy from the receiver is insufficient.

scholarly journals Computational analysis of transient turbulent flow and conjugate heat transfer characteristics in a solar collector panel with internal, rectangular fins and baffles

2010 ◽  
Vol 14 (1) ◽  
pp. 221-234 ◽  
Author(s):  
Rachid Saim ◽  
Said Abboudi ◽  
Boumédiene Benyoucef
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Turbulent Flow ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Solar Collector ◽  
Computational Analysis ◽  
Heat Transfer Characteristics ◽  
Thermal Exchange

The poor thermal exchange between the absorber and the fluid in the solar air flat plate collector, gives the bad performance and the mediocre thermal efficiency. The introduction of obstacles in the dynamic air vein of the solar collector in order to obtain a turbulent flow is a technique that improves the thermal exchange by convection between the air and the absorber. This article present a computational analysis on the turbulent flow and heat transfer in solar air collector with rectangular plate fins absorber and baffles which are arranged on the bottom and top channel walls in a periodically staggered way. To this end we solved numerically, by the finite volumes method, the conservation equations of mass, momentum and energy. The low Reynolds number k-? model was adopted for the taking into account of turbulence. The velocity and pressure terms of momentum equations are solved by the SIMPLE algorithm. The parameters studied include the entrance mass flow rate of air. The influence of the mass flow rate of air on the axial velocity and the efficiency of upward type baffled solar air heaters have been investigated numerically. The results show that the flow and the heat transfer characteristics are strongly dependent on mass-flow rate of air and the presence and/or the absence of the baffles and fins in the solar collector. It was observed that increasing the Reynolds number will increase the efficiency of the solar panel, as expected.

scholarly journals ANALISA LAJU PERPINDAHAN PANAS PADA KOLEKTOR SURYA TIPE PELAT DATAR DENGAN ABSORBER PASIR

2011 ◽  
Vol 1 (2) ◽  
Author(s):  
Made Wirawan ◽  
Rudy Sutanto
Keyword(s):  
Heat Transfer ◽  
Solar Energy ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Solar Collector ◽  
Alternative Energy ◽  
Heat Losses ◽  
Clear Sky ◽  
Potential Alternative

Solar energy constitute one of potential alternative energy to develop as a back up of energy. Especially for countries in khatulistiwa location belonging to Indonesia. For use solar energy needful collector that using absorber. Using sand as a absorber make up step for increase value and profit of sand, in a economics manner the price more cheap and easy to obtain than another absorber. The analysis use sand as a alternative absorber for solar collector did for understand rate of heat transfer to acceptanceof water. Dimention of collector are 560 mm x 310 mm with thick of sand absorber 10 mm and 1.2 mm for aluminum plate as a comparator. Observation did begin 10.00 am until 14.00 pm for the two of them in the weather clear sky. The rate of water in this research are 200 cc/min, 250 cc/min and 300 cc/mn for another dan at the same time. The result of analysis be obtained heat absortion by water for solar collector with aluminum absorber more large than sand absorber. The debit of water more and more large in the collector so absorb heat by water more large because incretion the mass flow rate of water (m  ). The heat losses in the solar collector aluminum absorber more than sand absorber.

Effect of pre-swirl nozzle closure modes on unsteady flow and heat transfer characteristics in a pre-swirl system of aero-engine

2021 ◽  
pp. 095441002110191
Author(s):  
Gaowen Liu ◽  
Zhao Lei ◽  
Aqiang Lin ◽  
Qing Feng ◽  
Yan Chen
Keyword(s):  
Heat Transfer ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Temperature Drop ◽  
Thermodynamic Characteristics ◽  
Circumferential Direction ◽  
Temperature Changes ◽  
Air Supply ◽  
Cooling Air

The pre-swirl system is of great importance for temperature drop and cooling air supply. This study aims to investigate the influencing mechanism of heat transfer, nonuniform thermodynamic characteristics, and cooling air supply sensitivity in a pre-swirl system by the application of the flow control method of the pre-swirl nozzle. A novel test rig was proposed to actively control the supplied cooling air mass flow rate by three adjustable pre-swirl nozzles. Then, the transient problem of the pre-swirl system was numerically conducted by comparison with 60°, 120°, and 180° rotating disk cavity cases, which were verified with the experiment results. Results show that the partial nozzle closure will aggravate the fluctuation of air supply mass flow rate and temperature. When three parts of nozzles are closed evenly at 120° in the circumferential direction, the maximum value of the nonuniformity coefficient of air supply mass flow rate changes to 3.1% and that of temperature changes to 0.25%. When six parts of nozzles are closed evenly at 60° in the circumferential direction, the maximum nonuniformity coefficient of air supply mass flow rate changes to 1.4% and that of temperature changes to 0.20%. However, different partial nozzle closure modes have little effect on the average air supply parameters. Closing 14.3% of the nozzle area will reduce the air supply mass flow rate by 9.9% and the average air supply temperature by about 1 K.

Heat Transfer and Flow Friction Characteristics for Compact Cold Plates

2003 ◽  
Vol 125 (1) ◽  
pp. 104-113 ◽  
Author(s):  
Chang-Yuan Liu ◽  
Ying-Huei Hung
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Nusselt Number ◽  
Thermal Resistance ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Average Nusselt Number ◽  
Cold Plate ◽  
Air Mass

Both experimental and theoretical investigations on the heat transfer and flow friction characteristics of compact cold plates have been performed. From the results, the local and average temperature rises on the cold plate surface increase with increasing chip heat flux or decreasing air mass flow rate. Besides, the effect of chip heat flux on the thermal resistance of cold plate is insignificant; while the thermal resistance of cold plate decreases with increasing air mass flow rate. Three empirical correlations of thermal resistance in terms of air mass flow rate with a power of −0.228 are presented. As for average Nusselt number, the effect of chip heat flux on the average Nusselt number is insignificant; while the average Nusselt number of the cold plate increases with increasing Reynolds number. An empirical relationship between Nu¯cp and Re can be correlated. In the flow frictional aspect, the overall pressure drop of the cold plate increases with increasing air mass flow rate; while it is insignificantly affected by chip heat flux. An empirical correlation of the overall pressure drop in terms of air mass flow rate with a power of 1.265 is presented. Finally, both heat transfer performance factor “j” and pumping power factor “f” decrease with increasing Reynolds number in a power of 0.805; while they are independent of chip heat flux. The Colburn analogy can be adequately employed in the study.

scholarly journals Thermal Characteristics Analysis on Multi- Heat Pipe Induced Heat Exchanger

2019 ◽  
Vol 9 (2S2) ◽  
pp. 143-147 ◽  
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Heat Pipe ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Cold Water ◽  
Hot Water ◽  
Working Fluid ◽  
Physical Parameters

In this investigation of multi heat pipe induced in heat exchanger shows the developments in heat transfer is to improve the efficiency of heat exchangers. Water is used as a heat transfer fluid and acetone is used as a working fluid. Rotameter is set to measure the flow rate of cold water and hot water. To maintain the parameter as experimental setup. Then set the mass flow rate of hot water as 40 LPH, 60LPH, 80 LPH, 100LPH, 120 LPH and mass flow rate of cold water as 20 LPH, 30 LPH, 40 LPH, 50 LPH, and 60 LPH. Then 40 C, 45 ºC, 50 ºC, 55 C, 60 ºC are the temperatures of hot water at inlet are maintained. To find some various physical parameters of Qc , hc , Re ,, Pr , Rth. The maximum effectiveness of the investigation obtained from condition of Thi 60 C, Tci 32 C and 100 LPH mhi, 60 LPH mci the maximum effectiveness attained as 57.25. Then the mhi as 100 LPH, mci as 60 LPH and Thi at 40 C as 37.6%. It shows the effectiveness get increased about 34.3 to the maximum conditions.

scholarly journals Contribution to the Parametric Study of the Performance of A Parabolic Trough Collector

2021 ◽  
Vol 321 ◽  
pp. 02016
Author(s):  
Belkacem Bouali ◽  
Hanane-Maria Regue
Keyword(s):  
Heat Transfer ◽  
Mass Flow ◽  
Flow Rate ◽  
Optimal Operation ◽  
Heat Transfer Fluid ◽  
Parabolic Trough ◽  
Parabolic Trough Collector ◽  
Heat Transfer Fluids ◽  
Ansys Cfx ◽  
Different Seasons

This paper presents an analysis of the performance of a parabolic trough collector (PTC) according to some key operating parameters. The effects of the secondary reflector, the length and thickness of the absorber tube (receiver tube) and the flow rate of the heat transfer fluid (HTF) are investigated. The main objective is to determine an optimal operation, which improves the performance of a traditional PTC. The target variables are the temperature at the outlet of the tube, the amount of energy collected by the HTF and the efficiency of the system. The solar flux data concern the city of LAGHOUAT located in the south of Algeria. Four days in different seasons are considered. The optical analysis of the system is performed by using the open source SolTrace code. The output of this analysis is used as a boundary condition for the CFD solver. The conjugate heat transfer and the fluid flow through the absorber tube are simulated by using ANSYS-CFX solver. Water is considered as heat transfer fluids. The obtained results show that the use of a curved secondary reflector significantly improves the performance of the traditional PTC. As the thickness of the tube increases, the heat storage in the material increases, which increases the temperature at the exit of the tube and therefore the efficiency of the system. However, the length of the tube depends on the mass flow of the HTF and vice versa. To keep the efficiency constant by choosing another length, it is necessary to choose a mass flow rate proportional to the flow rate corresponding to the initial length.

Sign in / Sign up

Export Citation Format

Share Document