scholarly journals Structure Analysis and Properties of Unleaded Brasses

2015 ◽  
Vol 60 (1) ◽  
pp. 323-328 ◽  
Author(s):  
S. Rzadkosz ◽  
J. Kozana ◽  
A. Garbacz-Klempka ◽  
M. Piękoś
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Light Microscopy ◽  
Structure Analysis ◽  
Structure And Properties ◽  
X Ray ◽  
Ecological Characteristics ◽  
The Matrix ◽  
Scanning Electron

Abstract The analysis of brasses regarding their microstructure, mechanical properties and ecological characteristics has been presented. The influence of characteristic alloying elements contained in the brasses and the possibilities of replacing them with other elements have been assessed. The paper contains the results of studies on the influence of chosen additional elements shaping the structure and properties of unleaded alloys based on Cu-Zn system as the matrix. The research aimed at determining the mechanism and the intensity of influence of such additives as tellurium and bismuth. The microstructures were investigated with the help of light microscopy and scanning electron microscopy with X-ray microanalysis (SEM-EDS) for determining significant changes of the properties.

Effect of Ca on Microstructure and Properties of Mg-Al-Si Alloys

2011 ◽  
Vol 194-196 ◽  
pp. 1369-1373 ◽  
Author(s):  
Chun Xiang Xu ◽  
Hui Ju ◽  
Yang Zhou
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Chinese Script ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ca Addition ◽  
The Matrix ◽  
Morphology Modification ◽  
Scanning Electron

Effect of Ca addition on the morphology modification in Mg-7Al-0.8Zn-0.2Mn-1Si (AS71) alloys has been investigated using X-ray diffraction (XRD), optical microscopy (OM), and scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and various testing machines. The results show that when adding 0.1 wt% Ca, a small fraction of Mg2Si change from Chinese script type to polygonal type; with the Ca addition up to 0.3 wt%, edges and angles of polygonal type Mg2Si phase are changed; further increase in Ca addition, the morphology of Mg2Si is changed to strip-like or spot-like one. Meanwhile, the addition of Ca results in the morphology of β- Mg17Al12 phase changing from discontinuous net-like to dispersive island-like. Ca exists as solid-soluting atomic in the matrix with small Ca addition while in the form of CaSi2 with large Ca addition. Optimal mechanical properties can be achieved when Ca addition is 0.3 wt%.

Research on compatibility and surface of high impact bio-based polyamide

2021 ◽  
pp. 095400832110055
Author(s):  
Yang Wang ◽  
Yuhui Zhang ◽  
Yuhan Xu ◽  
Xiucai Liu ◽  
Weihong Guo
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Crystallization Behavior ◽  
High Impact ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

The super-tough bio-based nylon was prepared by melt extrusion. In order to improve the compatibility between bio-based nylon and elastomer, the elastomer POE was grafted with maleic anhydride. Scanning Electron Microscopy (SEM) and Thermogravimetric Analysis (TGA) were used to study the compatibility and micro-distribution between super-tough bio-based nylon and toughened elastomers. The results of mechanical strength experiments show that the 20% content of POE-g-MAH has the best toughening effect. After toughening, the toughness of the super-tough nylon was significantly improved. The notched impact strength was 88 kJ/m2 increasing by 1700%, which was in line with the industrial super-tough nylon. X-ray Diffraction (XRD) and Differential Scanning Calorimetry (DSC) were used to study the crystallization behavior of bio-based PA56, and the effect of bio-based PA56 with high crystallinity on mechanical properties was analyzed from the microstructure.

Characteristics of Ni–Cr–Fe laser clad layers on EA4T steel

2017 ◽  
Vol 31 (16-19) ◽  
pp. 1744031
Author(s):  
Wenjing Chen ◽  
Hui Chen ◽  
Yongjing Wang ◽  
Congchen Li ◽  
Xiaoli Wang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cladding Layer ◽  
Metallurgical Bonding ◽  
The Matrix ◽  
Feeding Speed ◽  
Upper Bainite ◽  
Scanning Electron

The Ni–Cr–Fe metal powder was deposited on EA4T steel by laser cladding technology. The microstructure and chemical composition of the cladding layer were analyzed by optical microscopy (OM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The bonding ability between the cladding layer and the matrix was measured. The results showed that the bonding between the cladding layer and the EA4T steel was metallurgical bonding. The microstructure of cladding layer was composed of planar crystals, columnar crystals and dendrite, which consisted of Cr2Ni3, [Formula: see text] phase, M[Formula: see text]C6 and Ni3B phases. When the powder feeding speed reached 4 g/min, the upper bainite occurred in the heat affected zone (HAZ). Moreover, the tensile strength of the joint increased, while the yield strength and the ductility decreased.

The Impact Properties of a Polyurethane Composite Filled with Clay

2011 ◽  
Vol 197-198 ◽  
pp. 1100-1103
Author(s):  
Jian Li
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Mechanical Analysis ◽  
Impact Testing ◽  
Impact Properties ◽  
Polyurethane Composite ◽  
The Matrix ◽  
The Impact ◽  
Scanning Electron

A polyurethane/clay (PU/clay) composite was synthesized. The microstructure of the composite was examined by scanning electron microscopy. The impact properties of the composite were characterized by impact testing. The study on the structure of the composite showed that clays could be dispersed in the polymer matrix well apart from a few of clusters. The results from mechanical analysis indicated that the impact properties of the composite were increased greatly in comparison with pure polyurethane. The investigation on the mechanical properties showed that the impact strength could be obviously increased by adding 20 wt% (by weight) clay to the matrix.

UTILIZATION OF FLY ASH AND CONCRETE RESIDUE IN THE PRODUCTION OF GEOPOLYMER BRICKS

2017 ◽  
Vol 12 (1) ◽  
pp. 63-77 ◽  
Author(s):  
Siriporn Sirikingkaew ◽  
Nuta Supakata
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Compressive Strength ◽  
Phase Composition ◽  
Fly Ash ◽  
Industrial Waste ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

This study presents the development of geopolymer bricks synthetized from industrial waste, including fly ash mixed with concrete residue containing aluminosilicate compound. The above two ingredients are mixed according to five ratios: 100:0, 95:5, 90:10, 85:15, and 80:20. The mixture's physico-mechanical properties, in terms of water absorption and the compressive strength of the geopolymer bricks, are investigated according to the TIS 168-2546 standard. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyses are used to investigate the microstructure and the elemental and phase composition of the brick specimens. The results indicate that the combination of fly ash and concrete residue represents a suitable approach to brick production, as required by the TIS 168–2546 standard.

scholarly journals The Influence of A Mo Addition on the Interfacial Morphologies and Corrosion Resistances of Novel Fe-Cr-B Alloys Immersed in Molten Aluminum

Materials ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 256 ◽  
Author(s):  
Zicheng Ling ◽  
Weiping Chen ◽  
Weiye Xu ◽  
Xianman Zhang ◽  
Tiwen Lu ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Electron Probe ◽  
Molten Aluminum ◽  
Dendritic Structure ◽  
H13 Steel ◽  
X Ray ◽  
Transmission Electron ◽  
The Matrix ◽  
Scanning Electron

The influence of a Mo addition on the interfacial morphologies and corrosion resistances of novel Fe-Cr-B alloys in molten aluminum at 750 °C was systematically investigated using scanning electron microscopy, X-ray diffractometer, electron probe microanalysis, and transmission electron microscopy. The results indicated that Mo could not only strengthen the matrix but also facilitate the formation of borides. Furthermore, the microstructures of Mo-rich M2B boride changed from a local eutectic net-like structure to a typical coarse dendritic structure and a blocky hypereutectic structure with increasing Mo addition. This was true of the blocky Mo-rich M2B boride, rod-like Cr-rich M2B boride and the corrosion products, which had a synergistic effect on retarding of the diffusion of molten aluminum. Notably, the corrosion resistance of the Fe-Cr-B-Mo alloy, with an 8.3 wt.% Mo addition, was 3.8 times higher than that of H13 steel.

scholarly journals Amazonian Metakaolin Reactivity for Geopolymer Synthesis

2019 ◽  
Vol 2019 ◽  
pp. 1-7 ◽  
Author(s):  
Ruy A. Sá Ribeiro ◽  
Marilene G. Sá Ribeiro ◽  
Gregory P. Kutyla ◽  
Waltraud M. Kriven
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
X Ray Diffraction ◽  
Local Resource ◽  
X Ray ◽  
Potassium Sodium ◽  
Mixing Intensity ◽  
Amazonian Region ◽  
Scanning Electron

To determine the viability of using a local resource for geopolymer synthesis, geopolymers were synthesized using metakaolin made from clay mined in the Amazonian region of Brazil. Samples were made with mixed potassium-sodium and pure sodium metakaolin-based geopolymer. Samples were also made using commercial metakaolin (CMK) from BASF, Inc. as a comparison to the Amazonian metakaolin (AMK). Scanning electron microscopy was used to investigate the microstructure of the materials. X-ray diffraction was able to confirm the formation of geopolymer. The mechanical properties of AMK material were nearly equivalent to those based on CMK. Neither CMK nor AMK reacted completely, although samples made with CMK showed less unreacted material. By increasing the mixing intensity and duration, the amount of residual unreacted material was substantially reduced, and mechanical properties were improved.

Detection of Intermetallic Compounds in a Mg-5Al-3Ca-0.7Sr-0.2Mn Magnesium Alloy

2013 ◽  
Vol 197 ◽  
pp. 137-142 ◽  
Author(s):  
Tomasz Rzychoń ◽  
Janusz Szala ◽  
Tomasz Kukiełka
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Magnesium Alloy ◽  
Light Microscopy ◽  
Diffraction Analysis ◽  
Intermetallic Compounds ◽  
Intermetallic Phases ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

In this paper the results of microstructural investigations and methodology of detection of intermetallic compounds were reported. The microstructural investigations included the light microscopy, scanning electron microscopy, chemical microanalysis and X-ray diffraction analysis. It was found that the microstructure of Mg-5Al-3Ca-0.7Sr-0.2Mn alloy consists of α-Mg, (Mg,Al)2Ca, Al3Mg13(Sr,Ca), Mg2Ca and Al2Ca intermetallic phases. The correct detection of these phases requires the high magnifications and a large number of measurements fields.

scholarly journals Investigation of deformation and microstructure of bainite in Cu-9.97%Al-4.62%mn alloy

2014 ◽  
Vol 50 (1) ◽  
pp. 87-90 ◽  
Author(s):  
E. Aldirmaz ◽  
I. Aksoy
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Physical And Mechanical Properties ◽  
Compression Stress ◽  
X Ray Diffraction ◽  
Deformation Effect ◽  
X Ray ◽  
Deformation Test ◽  
Scanning Electron

In this study, some physical and mechanical properties in Cu-9.97%Al-4.62%Mn (wt%) alloy were investigated by X-ray diffraction (XRD), Scanning Electron Microscopy (SEM) and compression deformation test. Bainite phase were obtained in the samples according to SEM and XRD analyses. Compression stress was applied on the alloy in order to investigate the deformation effect on the bainite phase transformation. On the surface of the Cu-9.97%Al-4.62%Mn alloy after the deformation, both bainite and martensite variants formed.

Processing of Biodegradable Polymer Composite Using Soy Protein-Based Resin and Nanoclay

2016 ◽  
Author(s):  
Mohammad K. Hossain ◽  
Samira N. Shaily ◽  
Hadiya J. Harrigan ◽  
Terrie Mickens
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Optical Microscopy ◽  
Soy Protein ◽  
Poly Vinyl Alcohol ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

A completely biodegradable composite was fabricated from an herbal polymer, soy protein concentrate (SPC) resin. Soy protein was modified by adding 30 wt% of glycerol and 5 wt% of poly vinyl alcohol (PVA) to enhance its mechanical as well as thermal property. 3%, 5%, 10%, and 20% nanoclay (NC) were infused into the system. To evaluate its mechanical properties, crystallinity, thermal properties, bonding interaction, and morphological evaluation, tensile, X-ray diffraction (XRD), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and Fourier transform infrared spectroscopy (FTIR) tests, and optical microscopy (OM) and scanning electron microscopy (SEM) evaluation were performed. Tensile tests showed that the addition of nanoclay improved the mechanical properties of the modified resin. Soy protein is hydrophilic due to the presence of amino acids that contain various polar groups such as amine, carboxyl, and hydroxyl. As a result, polar nanoclay particles that are exfoliated can be evenly dispersed in the SPC resin. From experimental results, it is clear that adding of nanoclay with SPC resin significantly increased the stiffness of the SPC resin. A combination of 5% clay, 30% glycerol, and 5% PVA with the modified SPC resulted in the maximum stress of 18 MPa and Young modulus of 958 MPa. The modified SPC showed a reduced failure strain as well. X-ray diffraction curves showed an improvement of crystallinity of the prepared resin with increasing amount of nanoclay. Interaction among soy, glycerol, PVA, and nanoclay was clearly demonstrated from the FTIR analysis. Optical microscopy (OM) and scanning electron microscopy (SEM) micrographs revealed rougher surface in the nanoclay infused SPC samples compared to that of the neat one. SEM evaluation revealed rougher fracture surface in the NC infused samples.

Sign in / Sign up

Export Citation Format

Share Document