scholarly journals Kinematics of the Lumbo–Pelvic Complex under Different Loading Conditions

2019 ◽  
Vol 5 (1) ◽  
pp. 347-349
Author(s):  
Martin Weidling ◽  
Christian Voigt ◽  
Toni Wendler ◽  
Martin Heilemann ◽  
Michael Werner ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Axial Rotation ◽  
Image Correlation ◽  
Loading Conditions ◽  
Structural System ◽  
Lateral Bending ◽  
Test Rig ◽  
Hip Joints ◽  
Complex Structural ◽  
The Right

AbstractThe lumbo-pelvic complex is a highly complex structural system. The current investigation aims to identify the kinematics between interacting bone segments under different loading conditions. A specimen of the lumbo-pelvic complex was obtained from a human body donor and tested in a self-developed test rig. The experimental setup was designed to imitate extension, flexion, right and left lateral bending and axial rotation to the left and to the right, respectively. The vertebra L3 was firmly embedded and load was introduced via hip joints. Using a digital image correlation (DIC) system, the 3D motions of 15 markers at different landmarks were measured for each loadcase under cyclic loading. For each loadcase, the kinematics were analyzed in terms of three-dimensional relative movements between L3 and the sacrum. The usefulness of the experimental technique was demonstrated. It may serve for further biomechanical investigations of relative motion of sacroiliac and vertebral joints and deformation of bony structures.

Craniovertebral junction fixation with transarticular screws: biomechanical analysis of a novel technique

2003 ◽  
Vol 98 (2) ◽  
pp. 202-209 ◽  
Author(s):  
L. Fernando Gonzalez ◽  
Neil R. Crawford ◽  
Robert H. Chamberlain ◽  
Luis E. Perez Garza ◽  
Mark C. Preul ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Axial Rotation ◽  
Craniovertebral Junction ◽  
Biomechanical Analysis ◽  
Lateral Bending ◽  
Content Type ◽  
Additional Stability ◽  
A New Technique ◽  
Flexion And Extension ◽  
Fine Print

Object. The authors compared the biomechanical stability resulting from the use of a new technique for occipitoatlantal motion segment fixation with an established method and assessed the additional stability provided by combining the two techniques. Methods. Specimens were loaded using nonconstraining pure moments while recording the three-dimensional angular movement at occiput (Oc)—C1 and C1–2. Specimens were tested intact and after destabilization and fixation as follows: 1) Oc—C1 transarticular screws plus C1–2 transarticular screws; 2) occipitocervical transarticular (OCTA) plate in which C1–2 transarticular screws attach to a loop from Oc to C-2; and (3) OCTA plate plus Oc—C1 transarticular screws. Occipitoatlantal transarticular screws reduced motion to well within the normal range. The OCTA loop and transarticular screws allowed a very small neutral zone, elastic zone, and range of motion during lateral bending and axial rotation. The transarticular screws, however, were less effective than the OCTA loop in resisting flexion and extension. Conclusions. Biomechanically, Oc—C1 transarticular screws performed well enough to be considered as an alternative for Oc—C1 fixation, especially when instability at C1–2 is minimal. Techniques for augmenting these screws posteriorly by using a wired bone graft buttress, as is currently undertaken with C1–2 transarticular screws, may be needed for optimal performance.

scholarly journals Influence of Carrying Unstable Load on Thoracic Kinematics While Walking on a Curved Path

2021 ◽  
Vol 2071 (1) ◽  
pp. 012013
Author(s):  
D K Ngoc ◽  
A F Salleh ◽  
M S Salim ◽  
N Omar ◽  
K S Basarrudin ◽  
...  
Keyword(s):  
Sagittal Plane ◽  
Three Dimensional ◽  
Frontal Plane ◽  
Axial Rotation ◽  
Heel Strike ◽  
Virtual Lab ◽  
Flexion Extension ◽  
Spinal Kinematics ◽  
Load Intensity ◽  
The Right

Abstract This study investigated the effect of carrying unstable load on thoracic kinematics while walking on a curved path. Three-dimensional spinal kinematics were defined as the rotations between thoracic and the Virtual laboratory coordinate system (Tho/Virtual lab) which consisted of lateral bending (LB), flexion/extension (FE) and axial rotation (AR) in the frontal plane, sagittal plane and transverse plane, respectively. Eight healthy young adults (4 males and 4 females) performed loads carrying and walking on one meter radius curved path. Spinal kinematics was determined at the left leg heel strike and just before the right toe off during the curved path walking. As a result, a significant main effect of load intensity was found only on FE of (Tho/Virtual lab) at both left leg heel strike and right leg toe off. The study concluded that an increase in the load intensity of unstable load from 10% of body weight likely to generate more thorax extension.

Effect of Facetectomy on the Three-Dimensional Biomechanical Properties of the Fourth Canine Cervical Functional Spinal Unit: A Cadaveric Study

2017 ◽  
Vol 30 (06) ◽  
pp. 430-437 ◽  
Author(s):  
Nadja Bösch ◽  
Martin Hofstetter ◽  
Alexander Bürki ◽  
Beatriz Vidondo ◽  
Fenella Davies ◽  
...  
Keyword(s):  
Range Of Motion ◽  
Motion Analysis ◽  
Testing Machine ◽  
Three Dimensional ◽  
Axial Rotation ◽  
Biomechanical Properties ◽  
Lateral Bending ◽  
Coupled Motion ◽  
Functional Spinal Unit ◽  
Flexion Extension

Abstract Objective To study the biomechanical effect of facetectomy in 10 large breed dogs (>24 kg body weight) on the fourth canine cervical functional spinal unit. Methods Canine cervical spines were freed from all muscles. Spines were mounted on a six-degrees-of-freedom spine testing machine for three-dimensional motion analysis. Data were recorded with an optoelectronic motion analysis system. The range of motion wasdetermined inall threeprimary motionsaswellasrange of motion of coupled motions on the intact specimen, after unilateral and after bilateral facetectomy. Repeated-measures analysis of variance models were used to assess the changes of the biomechanical properties in the three treatment groups considered. Results Facetectomy increased range of motion of primary motions in all directions. Axial rotation was significantly influenced by facetectomy. Coupled motion was not influenced by facetectomy except for lateral bending with coupled motion axial rotation. The coupling factor (coupled motion/primary motion) decreased after facetectomy. Symmetry of motion was influenced by facetectomy in flexion–extension and axial rotation, but not in lateral bending. Clinical Significance Facet joints play a significant role in the stability of the cervical spine and act to maintain spatial integrity. Therefore, cervical spinal treatments requiring a facetectomy should be carefully planned and if an excessive increase in range of motion is expected, complications should be anticipated and reduced via spinal stabilization.

scholarly journals Correlation between different instrumentation variants and the degree of destabilization in treating cervical spondylotic spinal canal stenosis by unilateral hemilaminectomy with bilateral decompression: a biomechanical investigation

2021 ◽  
Author(s):  
Ingo Fiss ◽  
Dorothee Mielke ◽  
Veit Rohde ◽  
Marios Psychogios ◽  
Christoph Schilling
Keyword(s):  
Three Dimensional ◽  
Axial Rotation ◽  
Clinical Results ◽  
Biomechanical Study ◽  
Lateral Bending ◽  
Invasive Treatment ◽  
Canal Stenosis ◽  
Flexion Extension ◽  
Native Condition ◽  
Analysis System

Abstract Purpose Unilateral hemilaminectomy with bilateral decompression (BDZ) was proposed as an alternative decompressive procedure in cervical spondylotic myelopathy (CSM). Despite promising clinical results, the destabilizing effect is yet unknown. We therefore performed a biomechanical study to investigate whether lateral mass screw fixation should follow BDZ. Methods Six human C2–C7 cervical specimens were tested under various conditions: native, unilateral hemilaminectomy with bilateral decompression without/with fixation (BDZ/BDF), unilateral hemilaminectomy with bilateral decompression and unilateral foraminotomy without/with fixation (UFZ/UFF), unilateral hemilaminectomy with bilateral decompression and bilateral foraminotomy without/with fixation (BFZ/BFF), and laminectomy without/with fixation (LAZ/LAF). Instrumention was applied from C3–C6. For each condition, the three-dimensional kinematics of the cervical specimen were measured in three main loading directions with an ultrasonic motion analysis system. ANOVA was used to determine differences between the specific segment conditions to assess the parameter’s range of motion (ROM) and neutral zone (NZ). Results For flexion–extension, lateral bending and axial rotation, ROM of BDZ, UFZ, BFZ and LAZ remained at the level of the native condition (p > 0.74), whereas fixation reduced ROM significantly (p < 0.01). Between BDF, UFF, BFF and LAF, no significant differences in reduction in ROM were seen (p > 0.49). Results for NZ were equivalent to ROM in flexion–extension and lateral bending. For axial rotation, NZ remained almost constant on the native level for all tested conditions. Conclusion Bilateral decompression via a hemilaminectomy, even if combined with foraminotomy, could be a less invasive treatment option for multilevel CSM in patients with lordotic cervical alignment and absence of segmental instability.

scholarly journals Effect of Graded Facetectomy on Lumbar Biomechanics

2017 ◽  
Vol 2017 ◽  
pp. 1-6 ◽  
Author(s):  
Zhi-li Zeng ◽  
Rui Zhu ◽  
Yang-chun Wu ◽  
Wei Zuo ◽  
Yan Yu ◽  
...  
Keyword(s):  
Facet Joint ◽  
Three Dimensional ◽  
Element Model ◽  
Axial Rotation ◽  
Point Of View ◽  
Spinal Instability ◽  
Flexion Extension ◽  
Biomechanical Effect ◽  
Von Mises ◽  
The Right

Facetectomy is an important intervention for spinal stenosis but may lead to spinal instability. Biomechanical knowledge for facetectomy can be beneficial when deciding whether fusion is necessary. Therefore, the aim of this study was to investigate the biomechanical effect of different grades of facetectomy. A three-dimensional nonlinear finite element model of L3–L5 was constructed. The mobility of the model and the intradiscal pressure (IDP) of L4-L5 for standing were inside the data from the literature. The effect of graded facetectomy on intervertebral rotation, IDP, facet joint forces, and maximum von Mises equivalent stresses in the annuli was analyzed under flexion, extension, left/right lateral bending, and left/right axial rotation. Compared with the intact model, under extension, unilateral facetectomy increased the range of intervertebral rotation (IVR) by 11.7% and IDP by 10.7%, while the bilateral facetectomy increased IVR by 40.7% and IDP by 23.6%. Under axial rotation, the unilateral facetectomy and the bilateral facetectomy increased the IVR by 101.3% and 354.3%, respectively, when turned to the right and by 1.1% and 265.3%, respectively, when turned to the left. The results conclude that, after unilateral and bilateral facetectomy, care must be taken when placing the spine into extension and axial rotation posture from the biomechanical point of view.

3D kinematics of the equine metacarpophalangeal joint at walk and trot

2007 ◽  
Vol 02 (02) ◽  
pp. 86-91 ◽  
Author(s):  
D. Sha ◽  
J. Stick ◽  
N. Elvin ◽  
H. M. Clayton
Keyword(s):  
Soft Tissues ◽  
Sagittal Plane ◽  
Proximal Phalanx ◽  
Three Dimensional ◽  
Axial Rotation ◽  
Metacarpophalangeal Joint ◽  
Phase Extension ◽  
Flexion Extension ◽  
The Right ◽  
Value Decomposition

SummaryThe metacarpophalangeal (MCP) joint and its supporting soft tissues are common sites of injury in athletic horses. Equine gait analysis has focused on 2D analysis in the sagittal plane and little information is available which describes 3D motions of the MCP joint and their possible role in the development of injuries. The aim was to characterize the 3D rotations of the equine MCP joint during walking and trotting. Three-dimensional trajectories of marker triads fixed rigidly to the third metacarpus and proximal phalanx of the right forelimb of healthy horses were recorded at walk (n=4) and trot (n=6) at 120 Hz using eight infra-red cameras. Kinematics of the MCP joint were calculated in terms of helical angles between the two segments using singular-value decomposition and spatial attitude methods. The ranges of motion were: flexion/extension: 62 ± 7° at walk, 77 ± 5° at trot; adduction/abduction: 13 ± 7° at walk, 18 ± 7° at trot; and axial rotation: 6 ± 3° at walk, 9 ± 5° at trot. Flexion/extension had a consistent pattern and amplitude in all horses and appeared to be coupled with adduction/abduction, such that stance phase extension was accompanied by abduction and swing phase flexion was accompanied by adduction. Axial rotation was small in amount and the direction varied between horses but was consistent within an individual for the two gaits.

Load Sharing Among Spinal Elements of a Motion Segment in Extension and Lateral Bending

1987 ◽  
Vol 109 (4) ◽  
pp. 291-297 ◽  
Author(s):  
V. K. Goel ◽  
J. M. Winterbottom ◽  
J. N. Weinstein ◽  
Y. E. Kim
Keyword(s):  
Ligamentum Flavum ◽  
Linear Optimization ◽  
Compressive Load ◽  
Tensile Load ◽  
Loading Conditions ◽  
Lateral Bending ◽  
Capsular Ligament ◽  
Motion Segment ◽  
Axial Tensile ◽  
The Right

A linear optimization model was formulated using a semi-experimental protocol to estimate the forces in the spinal elements of a lumbar motion segment subjected to an extension or lateral bending moment with and without a 120 N compressive preload. A morphometer was used to acquire the three-dimensional locations of the disk center, facet centers and ligament origin and insertion sites with the specimen in a “neutral” position. The relative motion of the superior vertebra, under the loading conditions tested, was monitored using a Selspot II® system. These data allowed the formulation of the static equilibrium equations for the superior vertebra at each of the loading conditions mentioned above. A linear optimization technique was used, along with a suitable cost function, to find an optimum solution for the set of equations and imposed constraints. Results showed that for 6.9 Nm of extension moment, each facet carried a load of 52 N, with the disk carrying an axial tensile load of 104 N. At the 6.9 Nm extension moment coupled with 120 N preload, each facet carried a load of 77.2 N and the disk an axial tensile load of 37 N. In right lateral bending, with and without preload, the load was distributed among the right facet, the disk, the left ligamentum flavum and the left capsular ligament. At the 6.9 Nm load step without preload the right facet carried an axial load of 127.01 N with the disk carrying an axial compressive load of 7.8 N. Ligament forces for this step for the left ligamentum flavum and capsular ligament, respectively, were 61.03 N and 65.14 N. The addition of 120 N of preload reduced the load on the right facet to 83.5 N. The compressive load in the disk increased to 107.5 N. The corresponding ligament forces were 43.2 N (left ligamentum flavum) and 50.7 N (left capsular ligament).

Sign in / Sign up

Export Citation Format

Share Document