Synthesis and characterization of 1,4-diazophenylenebridged Cu-phthalocyanine polymer

e-Polymers ◽  
2004 ◽  
Vol 4 (1) ◽  
Author(s):  
Cemil Alkan ◽  
Leyla Aras ◽  
Güngör Gündüz
Keyword(s):  
Electrical Conductivity ◽  
Diazonium Salt ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Visible Spectroscopy ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Uv Visible ◽  
Soluble Part

Abstract A novel type of phthalocyanine polymer, 1,4-diazophenylene-bridged Cuphthalocyanine, was prepared from the diazonium salt of diaminobenzene and Cu(II) 1,8,15,22-tetraaminophthalocyanine. The polymer is partially soluble in tetrahydrofuran, dichloromethane, and dimethylformamide. Characterization of the polymer was performed by IR and UV-visible spectroscopy, X-ray diffraction, ash analysis, viscometry, differential scanning calorimetry and thermogravimetric analysis. The molecular weight of the soluble part of the polymer was determined by ebullioscopy. Electrical conductivity of the polymer and its doped samples were determined by the 4-probe technique. It was found that the electrical conductivity increased up to 10-4 S/cm after doping. The redox behaviour of the polymer was investigated utilizing cyclic voltammetry.

scholarly journals Synthesis and characterization of erbium trioxide nanoparticles as photocatalyzers for degradation of methyl orange dye

2019 ◽  
Vol 12 (1) ◽  
pp. 15-21 ◽  
Author(s):  
Rifat Mohammed Dakhil ◽  
Tayser Sumer Gaaz ◽  
Ahmed Al-Amiery ◽  
Mohd S. Takriff ◽  
Abdul Amir H. Kadhum
Keyword(s):  
Methyl Orange ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Visible Spectroscopy ◽  
X Ray ◽  
Uv Visible ◽  
Methyl Orange Dye ◽  
Microscopy Techniques ◽  
Degradation Of Methyl Orange

Abstract. The present work focuses on the photocatalytic degradation of methyl orange (MO) on erbium trioxide nanoparticles (Er2O3 NPs). In this study, Er2O3 nanoparticles were synthesized and fully characterized via various techniques, including X-ray diffraction, UV–visible spectroscopy and scanning electron microscopy techniques. The results revealed that the photocatalytic activity of the prepared Er2O3 NPs was manifested in MO photodegradation. The optimum efficiency obtained was 16 %.

Characterization of New Nonstoichiometric Ferroelectric (Li0.95Cu0.15)Ta0.76Nb0.19O3 and Comparative Study With (Li0.95Cu0.15)Ta0.57Nb0.38O3 as Photocatalysts in Microbial Fuel Cells

2018 ◽  
Vol 16 (2) ◽  
Author(s):  
S. Louki ◽  
N. Touach ◽  
A. Benzaouak ◽  
V. M. Ortiz-Martínez ◽  
M. J. Salar-García ◽  
...  
Keyword(s):  
Power Density ◽  
Microbial Fuel Cells ◽  
Removal Rate ◽  
Oxygen Demand ◽  
Ferroelectric Material ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Uv Visible

This work investigates the photocatalytic activity of new ferroelectric material with formula (Li0.95Cu0.15)Ta0.76Nb0.19O3 (LT76) in a single chamber microbial fuel cell (MFC) and compares its performance with the similar photocatalyst (Li0.95Cu0.15)Ta0.57Nb0.38O3 (LT57). The photocatalysts LT76 and LT57 were synthesized by ceramic route under the same conditions, with the same starting materials. The ratio Ta/Nb was fixed at 4.0 and 1.5 for LT76 and LT57, respectively. These phases were characterized by different techniques including X-ray diffraction (XRD), transmission electronic microscopy (TEM), particle size distribution (PSD), differential scanning calorimetry (DSC), and ultraviolet (UV)–visible (Vis). The new photocatalyst LT76 presents specific surface area of 0.791 m2/g and Curie temperature of 1197 °C. The photocatalytic efficiency of this material is assessed in terms of wastewater treatment and electricity generation by power density and removal rate of chemical oxygen demand (COD) in the presence of a light source. The values of maximum power density and COD removal were 19.77 mW/m3 and 93%, respectively, for LT76.

scholarly journals Stacking Control by Molecular Symmetry of Sterically Protected Phthalocyanines

Molecules ◽  
2020 ◽  
Vol 25 (23) ◽  
pp. 5552
Author(s):  
Ryota Kudo ◽  
Masahiro Sonobe ◽  
Yoshiaki Chino ◽  
Yu Kitazawa ◽  
Mutsumi Kimura
Keyword(s):  
Lamellar Structure ◽  
Synthesis And Characterization ◽  
Molecular Symmetry ◽  
X Ray Diffraction ◽  
Melting Points ◽  
Scanning Calorimetry ◽  
Structural Isomers ◽  
X Ray ◽  
Temperature Controlled

The synthesis and characterization of two phthalocyanine (Pc) structural isomers, 1 and 2, in which four 2,6-di(hexyloxy)phenyl units were attached directly to the 1,8,15,22- or 1,4,15,18-positions of the Pc rings, are described. Both Pcs 1 and 2 exhibited low melting points, i.e., 120 and 130 °C respectively, due to the reduction in intermolecular π-π interaction among the Pc rings caused by the steric hindrance of 2,6-dihexyloxybenzene units. The thermal behaviors were investigated with temperature-controlled polarizing optical microscopy, differential scanning calorimetry, powder X-ray diffraction, and absorption spectral analyses. Pc 1, having C4h molecular symmetry, organized into a lamellar structure containing lateral assemblies of Pc rings. In contrast, the other Pc 2 revealed the formation of metastable crystalline phases, including disordered stacks of Pcs due to rapid cooling from a melted liquid.

Synthesis and Electrochemistry of Aluminum Porphycenes: Crystal and Molecular Structure of Methyl-σ-Bonded Aluminum Etioporphycene

1997 ◽  
Vol 01 (02) ◽  
pp. 109-119 ◽  
Author(s):  
ROGER GUILARD ◽  
VIRGINIE PICHON-PESME ◽  
HASSANE LACHEKAR ◽  
CLAUDE LECOMTE ◽  
ALLY M. AUKAULOO ◽  
...  
Keyword(s):  
Molecular Structure ◽  
Crystal And Molecular Structure ◽  
Structural Data ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
H Nmr ◽  
Axial Ligands ◽  
Uv Visible

The synthesis and characterization of three monomeric aluminum porphycenes with anionic or σ-bonded axial ligands is reported. The investigated compounds are represented as ( EtioPc ) Al ( CH 3) and ( EtioPc ) AlX where EtioPc represents the dianion of etioporphycene and X = Cl − or OH −. Each synthesized complex was characterized by mass spectrometry. 1 H NMR, IR and UV-visible spectroscopies as well as by electrochemistry. Comparisons are made between the properties of complexes in the aluminum etioporphycene series and related chloro- or methyl σ-bonded Al ( III ) porphyrins containing octaethylporphyrin ( OEP ) or tetraphenylporphyrin ( TPP ) macrocycles. Comparisons are also made between the currently investigated compounds and a previously reported Al ( III ) μ-oxo dimer, [( EtioPc ) Al ]2 O . In addition, the crystal and molecular structure of ( EtioPc ) Al ( CH 3) was determined by X-ray diffraction. The molecular structure of this methyl-σ-bonded aluminum etioporphycene provides the first structural data for an aluminum porphycene compound. The aluminum(III) atom in ( EtioPc ) Al ( CH 3) is pentacoordinated and is located 0.54 Å from the plane of the four N -nitrogens.

In Situ Polymerization and Characterization of Poly(ε-caprolactone)/Layered Double Hydroxide Nanocomposites

2012 ◽  
Vol 557-559 ◽  
pp. 371-374
Author(s):  
Lian Liu ◽  
Teng Yu ◽  
Pei Wang ◽  
Guang Shuo Wang
Keyword(s):  
Layered Double Hydroxide ◽  
In Situ Polymerization ◽  
X Ray Diffraction ◽  
Visible Spectroscopy ◽  
X Ray ◽  
Uv Visible ◽  
Absorbance Peak ◽  
Double Hydroxide

Nanocomposites of poly(ε-caprolactone) (PCL) and layered double hydroxide (LDH) were prepared by in situ polymerization at low LDHs loadings in this work. The resultants were characterized by FTIR spectroscopy, X-ray diffraction (XRD), differential scanning calorimeter (DSC) and UV-visible spectroscopy (UV-vis). FTIR showed that the PCL/LDHs nanocomposites were prepared successfully by in situ polymerization and XRD spectra showed that the crystal structure did not change greatly in the presence of LDHS. DSC results confirmed that LDHs could act as nucleating agents. UV-vis spectra showed that LDHs had stronger absorbance peak than LDH. Moreover, the PCL/LDHs nanocomposites had strong anti-ultraviolet effect by introduction of LDHs into polymer matrix.

Microwave-Hydrothermal Synthesis and Characterization of Graphene

2012 ◽  
Vol 602-604 ◽  
pp. 917-920 ◽  
Author(s):  
Zhen Hui Xiao ◽  
Shui Sheng Wu ◽  
Yan Lin Sun ◽  
Yu Lin Zhao ◽  
Ya Ming Wang
Keyword(s):  
Chemical Reduction ◽  
Visible Spectrum ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
Microwave Hydrothermal ◽  
Ft Ir ◽  
Uv Visible ◽  
Scanning Electron

Graphene was synthesized by microwave-hydrothermal chemical reduction of graphite oxide using hydrazine hydrate as the reducing agent. Graphene was characterized using X-ray diffraction, UV-visible spectrum, FT-IR spectrum and scanning electron microscopy. Results indicated that the as-prepared graphene was wrinkled and comprised fewer graphenes with a highly crystalline structure.

scholarly journals Synthesis and characterization of allyl- and vinyl-substituted 1,2-bis(tetrazolo)ethanes as polymeric precursors

2016 ◽  
Vol 71 (12) ◽  
pp. 1199-1209
Author(s):  
Vera A. Hartdegen ◽  
Maximilian S. Hofmayer ◽  
Konstantin Karaghiosoff ◽  
Thomas M. Klapötke
Keyword(s):  
Allyl Bromide ◽  
2D Nmr ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
2D Nmr Spectroscopy ◽  
X Ray ◽  
Physical Stimuli ◽  
Thermal Stability Of

AbstractOn the basis of 1,2-bis(5-tetrazolo)ethane (BTE) the corresponding twofold vinyl and allyl N-substituted derivatives were synthesized using 1,2-dibromoethane and allyl bromide, respectively. The compounds were obtained as two different constitutional isomers. Both species were analyzed using NMR and IR spectroscopy, elemental analysis, as well as mass spectrometry. In the case of the diallyl bistetrazoles, the two isomers were characterized using 2D NMR spectroscopy. The synthesis of the divinyl compounds gave crystals of the 2,2′-N-substituted isomer, which were analyzed by single-crystal X-ray diffraction. The thermal stability of the compounds was determined using differential scanning calorimetry (DSC) and gave decomposition temperatures around 190°C and 230°C. For the investigation of the inherent energetic potential, sensitivities toward physical stimuli and detonation parameters were determined. The compounds turned out to be insensitive toward friction and impact and possess moderate energetic properties.

DSC AND ELECTRICAL CONDUCTIVITY STUDIES ON SUPERIONIC ALL-GLASS PHOSPHATE-BASED COMPOSITES

2011 ◽  
Vol 04 (02) ◽  
pp. 139-142
Author(s):  
JAN L. NOWIŃSKI ◽  
WIOLETA ŚLUBOWSKA ◽  
JERZY E. GARBARCZYK ◽  
MAREK WASIUCIONEK
Keyword(s):  
Electrical Conductivity ◽  
Electrical Properties ◽  
Phosphate Glasses ◽  
Superionic Conductors ◽  
X Ray Diffraction ◽  
Glass Composite ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Dsc Studies

The work investigates electrical properties of all-glass composite Ag +-ion conductors based on silver phosphate glasses. A combination of X-ray diffraction (XRD) and differential scanning calorimetry (DSC) was used for characterization of the samples. The impedance spectroscopy (IS) was applied to determine the electrical conductivity in a wide temperature range (from -140 to +20°C). Results of the DSC studies indicate that all-glass materials prepared from the powdered glasses are bi-phasic. On the other hand their electrical properties resemble homogeneous rather than heterogeneous superionic conductors.

Chemical synthesis and characterization of polyaniline-molybdenum trisulfide composite

1999 ◽  
Vol 14 (5) ◽  
pp. 1805-1813 ◽  
Author(s):  
Florence Fusalba ◽  
Daniel Bélanger
Keyword(s):  
Aqueous Solution ◽  
Photoelectron Spectroscopy ◽  
Synthesis And Characterization ◽  
Scanning Electron Micrographs ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Chemical Polymerization ◽  
X Ray ◽  
Scanning Electron

A novel polyaniline-molybdenum trisulfide composite has been prepared by chemical polymerization from an acidic (1 M HCl) aqueous solution containing aniline and ammonium tetrathiomolybdate. The presence of molybdenum trisulfide in the polyaniline matrix induces morphological change to the polymer as evidenced by scanning electron micrographs. X-ray diffraction and differential scanning calorimetry indicate that polyaniline-molybdenum trisulfide is slightly less crystalline than polyaniline-HCl. X-ray photoelectron spectroscopy (XPS) and elemental analysis have been used to confirm the presence of molybdenum trisulfide in the polymer matrix. The XPS data also confirm that molybdenum trisulfide and tetrathiomolybdate anions are present with polyaniline to form a new inorganic-organic composite.

Synthesis and Characterization of LiMn2O4 Nanoparticles Using Citric Acid as Chelating Agent

2009 ◽  
Vol 67 ◽  
pp. 227-232 ◽  
Author(s):  
Gurpreet Singh ◽  
Amrish Panwar ◽  
Anjan Sil ◽  
Sudipto Ghosh
Keyword(s):  
Citric Acid ◽  
Room Temperature ◽  
Sol Gel ◽  
Chelating Agent ◽  
Synthesis And Characterization ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Powder Particles

Nanocrystalline LiMn2O4 powder was synthesized by sol-gel method using citric acid as a chelating agent. The powders were characterized by X-ray diffraction (XRD), Field emission scanning electron microscopy (FESEM), Differential scanning calorimetry (DSC), Differential thermal analysis (DTA), Impedance spectroscopy (IS) and Electrochemical measurements. The powder particles having slight agglomeration characteristics were found to have prismatic morphology and a wider size distribution from 50 nm to 200 nm, which provides good packing density of the material. The electrical conductivity of the powder at room temperature is in the order of ~10-5 S/cm. The structural stability of LiMn2O4 cubic spinel over the temperature range of battery operation was assessed. Electrochemical performance of the material shows a discharge capacity of ~130 mAh/gm.

Sign in / Sign up

Export Citation Format

Share Document