Structure and properties of styrene-butadiene rubber/ pristine clay nanocomposites prepared by latex compounding method

e-Polymers ◽  
2007 ◽  
Vol 7 (1) ◽  
Author(s):  
Mahdi Abdollahi ◽  
Ali Rahmatpour ◽  
Jamal Aalaie ◽  
Homayon Hossein Khanli
Keyword(s):  
Mechanical Properties ◽  
Layered Silicate ◽  
Clay Content ◽  
Mechanical Tests ◽  
Styrene Butadiene Rubber ◽  
Clay Nanocomposites ◽  
Butadiene Rubber ◽  
Initial Modulus ◽  
Elastic Responses ◽  
Styrene Butadiene

AbstractStyrene- butadiene rubber (SBR)/ clay nanocomposites were prepared by mixing the SBR latex with aqueous clay dispersion and co-coagulating the mixture. Tapping mode AFM and XRD were applied to characterize the structure of nanocomposites. It was found that fully exfoliated structure could be obtained by this method only when the low loading of layered silicate (< 10 phr) is used. With increasing the clay content, both non-exfoliated (stacked layers) and exfoliated structures can be observed simultaneously in the nanocomposites. The results of mechanical tests on the vulcanized pure SBR and SBR/ clay nanocomposites showed that the nanocomposites presents better mechanical properties than clayfree SBR vulcanizate. Furthermore, initial modulus, tensile strength, tensile strain at break, hardness (shore A) and tear strength increased with increasing the clay content, indicating the nanoreinforcement effect of clay on the mechanical properties of SBR/ clay nanocomposites. Compared to the clay free SBR vulcanizate, the nanocomposite vulcanizates exhibit a lower tanδ peak value, higher storage modulus and higher tanδ value at the rubbery region (0-60 °C) which indicate that the elastic responses of pure SBR towards deformation are strongly influenced by the presence of nanodisperced natural sodium montmorillonite layers especially completely exfoliated silicate layers.

Structure and Mechanical Properties of Carboxylated Styrene-Butadiene Rubber (XSBR)/Pristine Clay Nanocomposites

e-Polymers ◽  
2007 ◽  
Vol 7 (1) ◽  
Author(s):  
Mahdi Abdollahi ◽  
Ali Rahmatpour ◽  
Homayon Hossein Khanli
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Tensile Strain ◽  
Clay Content ◽  
Mechanical Tests ◽  
Styrene Butadiene Rubber ◽  
Clay Nanocomposites ◽  
Butadiene Rubber ◽  
Carboxylated Styrene Butadiene Rubber ◽  
Styrene Butadiene

AbstractCarboxylated styrene- butadiene rubber (XSBR)/clay nanocomposites were prepared by mixing the XSBR latex with aqueous clay dispersion and cocoagulating the mixture. TEM and XRD were applied to characterize the structure of nanocomposites. Fully exfoliated structure was observed for the nanocomposites containing equal to or less than 10 phr (weight parts per hundred) clay. With increasing the clay content to 20 phr, both non-exfoliated (stacked layers) and exfoliated structures can be observed simultaneously in the nanocomposites. The results of mechanical tests on the vulcanized clay-free XSBR and XSBR/clay nanocomposites showed that the nanocomposites present better mechanical properties than clay-free XSBR vulcanizate. Furthermore, modulus, tensile strength, tensile strain at break and hardness (shore A) increased with increasing the clay content, indicating the nanoreinforcement effect of clay on the mechanical properties of XSBR/ clay nanocomposites.

Styrene butadiene rubber-clay nanocomposites using a latex method: morphology and mechanical properties

2007 ◽  
Vol 14 (5-6) ◽  
pp. 409-425 ◽  
Author(s):  
Wonho Kim ◽  
Byung-Suk Kang ◽  
Seong-Gyu Cho ◽  
Chang-Sik Ha ◽  
Jong-Woo Bae
Keyword(s):  
Mechanical Properties ◽  
Styrene Butadiene Rubber ◽  
Clay Nanocomposites ◽  
Butadiene Rubber ◽  
Styrene Butadiene ◽  
Morphology And Mechanical Properties

Styrene-butadiene rubber/cellulose II/clay nanocomposites prepared by cocoagulation-mechanical properties

2010 ◽  
Vol 120 (3) ◽  
pp. 1468-1474 ◽  
Author(s):  
Carmen Lane Giri Zine ◽  
Alberto Justino da Conceição ◽  
Leila L. Y. Visconte ◽  
Edson Noriyuki Ito ◽  
Regina C. R. Nunes
Keyword(s):  
Mechanical Properties ◽  
Styrene Butadiene Rubber ◽  
Clay Nanocomposites ◽  
Cellulose Ii ◽  
Butadiene Rubber ◽  
Styrene Butadiene

scholarly journals Electron Beam Modification on Dielectric, Thermal, and Thermo-mechanical Properties of Styrene Butadiene Rubber/ Clay Nanocomposites

2021 ◽  
Vol 0 (0) ◽  
pp. 1-9
Author(s):  
AHMED EL-BAYOUMI ◽  
mohamed madani ◽  
mohamed Atta ◽  
GAMAL Nasr ◽  
Samier Hamza
Keyword(s):  
Mechanical Properties ◽  
Electron Beam ◽  
Styrene Butadiene Rubber ◽  
Clay Nanocomposites ◽  
Butadiene Rubber ◽  
Styrene Butadiene

scholarly journals Effect of Graphene Oxide Modified with Organic Amine on the Aging Resistance, Rolling Loss and Wet-Skid Resistance of Solution Polymerized Styrene-Butadiene Rubber

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1025
Author(s):  
Songhan Wan ◽  
Xiaobin Lu ◽  
Hongguo Zhao ◽  
Songbo Chen ◽  
Shuwei Cai ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Graphene Oxide ◽  
Mechanical Tests ◽  
Good Effect ◽  
Styrene Butadiene Rubber ◽  
Skid Resistance ◽  
Butadiene Rubber ◽  
Aging Resistance ◽  
Styrene Butadiene ◽  
Wet Skid Resistance

Graphene oxide (GO) was modified by p-phenylenediamine (PPD), aiming at improving the wet-skid resistance and reduce the rolling loss of solution polymerized styrene-butadiene rubber (SSBR). PPD with amino groups enabled GO to obtain anti-aging function. The structure of modified GO (PPD-GO) was characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and Raman spectroscopy. Mechanical tests showed that the mechanical properties of SSBR before and after aging were improved by adding PPD-GO. The results of thermogravimetric-differential scanning calorimeter synchronization analysis (TGA-DSC) indicated that SSBR/PPD-GO obtained good thermo-oxidative stability. The dynamic mechanical analysis (DMA) of SSBR composites showed that the mechanical loss factor (tanδ) peak moved to high temperature with the content of PPD-GO. The tanδ values of SSBR composites showed that it had a good effect on improving the wet-skid resistance and reducing the rolling loss of SSBR by adjusting the content of PPD-GO. In particular, with the addition of 4 phr GO, SSBR was effectively improved in mechanical properties, aging resistance, wet-skid resistance and low rolling loss.

scholarly journals Analysis of the Impact on the Mechanical Properties of Modification of Oligohydroxyethers in Organic Solvent Solution with Rubbers

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 519
Author(s):  
Vitalii Bezgin ◽  
Agata Dudek ◽  
Adam Gnatowski
Keyword(s):  
Mechanical Properties ◽  
Scientific Paper ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Molecular Weights ◽  
Wide Range ◽  
Strength Tests ◽  
Materials Used ◽  
Styrene Butadiene ◽  
The Impact

This paper proposes and presents the chemical modification of linear hydroxyethers (LHE) with different molecular weights (380, 640, and 1830 g/mol) with the addition of three types of rubbers (polysulfide rubber (PSR), polychloroprene rubber (PCR), and styrene-butadiene rubber (SBR)). The main purpose of choosing this type of modification and the materials used was the possibility to use it in industrial settings. The modification process was conducted for a very wide range of modifier additions (rubber) per 100 g LHE. The materials obtained in the study were subjected to strength tests in order to determine the effect of the modification on functional properties. Mechanical properties of the modified materials were improved after the application of the modifier (rubber) to polyhydroxyether (up to certain modifier content). The most favorable changes in the tested materials were registered in the modification of LHE-1830 with PSR. In the case of LHE-380 and LHE-640 modified in cyclohexanol (CH) and chloroform (CF) solutions, an increase in the values of the tested properties was also obtained, but to a lesser extent than for LHE-1830. The largest changes were registered for LHE-1830 with PSR in CH solution: from 12.1 to 15.3 MPa for compressive strength tests, from 0.8 to 1.5 MPa for tensile testing, from 0.8 to 14.7 MPa for shear strength, and from 1% to 6.5% for the maximum elongation. The analysis of the available literature showed that the modification proposed by the authors has not yet been presented in any previous scientific paper.

Study on structures, dynamics and mechanical properties of styrene butadiene rubber (SBR)/silica interfaces: A fully atomistic molecular dynamics

Polymer ◽  
2021 ◽  
Vol 218 ◽  
pp. 123523
Author(s):  
Mengyu Zhou ◽  
Jun Liu ◽  
Guanyi Hou ◽  
Haibo Yang ◽  
Liqun Zhang
Keyword(s):  
Mechanical Properties ◽  
Molecular Dynamics ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Styrene Butadiene

scholarly journals Hybrid Silica-Based Fillers in Nanocomposites: Influence of Isotropic/Isotropic and Isotropic/Anisotropic Fillers on Mechanical Properties of Styrene-Butadiene (SBR)-Based Rubber

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2413
Author(s):  
Mariapaola Staropoli ◽  
Vincent Rogé ◽  
Enzo Moretto ◽  
Joffrey Didierjean ◽  
Marc Michel ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Silica Nanoparticles ◽  
Synergetic Effect ◽  
Mechanical Analysis ◽  
Rubber Matrix ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Precipitated Silica ◽  
Scanning Transmission ◽  
Styrene Butadiene

The improvement of mechanical properties of polymer-based nanocomposites is usually obtained through a strong polymer–silica interaction. Most often, precipitated silica nanoparticles are used as filler. In this work, we study the synergetic effect occurring between dual silica-based fillers in a styrene-butadiene rubber (SBR)/polybutadiene (PBD) rubber matrix. Precipitated Highly Dispersed Silica (HDS) nanoparticles (10 nm) have been associated with spherical Stöber silica nanoparticles (250 nm) and anisotropic nano-Sepiolite. By imaging filler at nano scale through Scanning Transmission Electron Microscopy, we have shown that anisotropic fillers align only in presence of a critical amount of HDS. The dynamic mechanical analysis of rubber compounds confirms that this alignment leads to a stiffer nanocomposite when compared to Sepiolite alone. On the contrary, spherical 250 nm nanoparticles inhibit percolation network and reduce the nanocomposite stiffness.

Sign in / Sign up

Export Citation Format

Share Document