Dynamic Performance Comparison for MPPT-PV Systems using Hybrid Pspice/Matlab Simulation

2016 ◽  
Vol 17 (5) ◽  
pp. 529-539 ◽  
Author(s):  
N. Aouchiche ◽  
M. Becherif ◽  
A. HadjArab ◽  
M. S. Aitcheikh ◽  
H. S. Ramadan ◽  
...  
Keyword(s):  
Dynamic Performance ◽  
Performance Comparison ◽  
Atmospheric Conditions ◽  
Matlab Simulation ◽  
Pv System ◽  
Simulation Tools ◽  
Pv Systems ◽  
Pv Panel ◽  
Simulation Techniques ◽  
Power Point

Abstract The power generated by solar photovoltaic (PV) module depends on the surrounding irradiance and temperature. This paper presents a hybrid Matlab™/Pspice™ simulation model of PV system, combined with Cadence software SLPS. The hybridization is performed in order to gain the advantages of both simulation tools such as accuracy and efficiency in both Pspice electronic circuit and Matlab™ mathematical modelling respectively. For this purpose, the PV panel and the boost converter are developed using Pspice™ and hybridized with the mathematical Matlab™ model of maximum power point method controller (MPPT) through SLPS. The main objective is verify the significance of using the proposed hybrid simulation techniques in comparing the different MPPT algorithms such as the perturbation and observation (P&O), incremental of conductance (Inc-Cond) and counter reaction voltage using pilot cell (Pilot-Cell). Various simulations are performed under different atmospheric conditions in order to evaluate the dynamic behaviour for the system under study in terms of stability, efficiency and rapidity.

scholarly journals Improved Fractional Open Circuit Voltage MPPT Methods for PV Systems

Electronics ◽  
2019 ◽  
Vol 8 (3) ◽  
pp. 321 ◽  
Author(s):  
Dmitry Baimel ◽  
Saad Tapuchi ◽  
Yoash Levron ◽  
Juri Belikov
Keyword(s):  
Open Circuit Voltage ◽  
Open Circuit ◽  
Maximum Power ◽  
Pv System ◽  
Maximum Power Point ◽  
Pv Systems ◽  
Point Tracking ◽  
Pv Panel ◽  
Power Point Tracking ◽  
Power Point

This paper proposes two new Maximum Power Point Tracking (MPPT) methods which improve the conventional Fractional Open Circuit Voltage (FOCV) method. The main novelty is a switched semi-pilot cell that is used for measuring the open-circuit voltage. In the first method this voltage is measured on the semi-pilot cell located at the edge of PV panel. During the measurement the semi-pilot cell is disconnected from the panel by a pair of transistors, and bypassed by a diode. In the second Semi-Pilot Panel method the open circuit voltage is measured on a pilot panel in a large PV system. The proposed methods are validated using simulations and experiments. It is shown that both methods can accurately estimate the maximum power point voltage, and hence improve the system efficiency.

Dynamic Performance Comparison for MPPT-PV Systems using Hybrid Pspice/Matlab Simulation

ENERGYO ◽  
2018 ◽  
Author(s):  
N. Aouchiche ◽  
M. Becherif ◽  
A. HadjArab ◽  
M. S. Aitcheikh ◽  
H. S. Ramadan ◽  
...  
Keyword(s):  
Dynamic Performance ◽  
Performance Comparison ◽  
Matlab Simulation ◽  
Pv Systems

scholarly journals Trusted Simulation Using Proteus Model for a PV System: Test Case of an Improved HC MPPT Algorithm

Energies ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1943
Author(s):  
Abdelilah Chalh ◽  
Aboubakr El Hammoumi ◽  
Saad Motahhir ◽  
Abdelaziz El Ghzizal ◽  
Umashankar Subramaniam ◽  
...  
Keyword(s):  
Hill Climbing ◽  
Test Case ◽  
Pv System ◽  
Real Experiment ◽  
The Real ◽  
Simulation Tools ◽  
Pv Systems ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Power Point

The real implementation of the maximum power point tracking (MPPT) controllers for the photovoltaic (PV) systems is still a big challenge for researchers working in this field. Often, they use simulation tools to assess the performance of their MPPT algorithms before actual implementation. In this context, this paper aims to propose a trusted simulation of a PV system designed under Proteus software. The proposed PV simulator can be used to verify and evaluate the performance of MPPT algorithms with a closer approximation to the real implementation. The main advantage of this model that it contains a real microcontroller, as can be found in reality, so that same code for the MPPT algorithm used in the simulation will be used in real implementation. In contrast, when using (Powersim Software) PSIM or Matlab/Simulink, the code of the algorithm must be rewritten once the real experiment begins, because these tools don’t provide a microcontroller or an electronic board in which our algorithm can be implemented and tested in the same way as the real experiment. After this section, a modified Hill-Climbing (HC) algorithm is introduced. The proposed algorithm can avoid the drift problem posed by conventional HC under a fast variation in insolation. The simulation results show that this method presents good performance in terms of efficiency (99.21%) and response time (10 ms), which improved by 1.2% and 70 ms respectively compared to the conventional HC algorithm.

scholarly journals Influence of Parasitic Resistances on the Input Resistance of Buck and Boost Converters in Maximum Power Point Tracking (MPPT) Systems

Electronics ◽  
2021 ◽  
Vol 10 (12) ◽  
pp. 1464
Author(s):  
Marcin Walczak ◽  
Leszek Bychto
Keyword(s):  
Input Resistance ◽  
Load Resistance ◽  
Maximum Power ◽  
Solar Panels ◽  
Maximum Power Point ◽  
Boost Converters ◽  
Pv Systems ◽  
Point Tracking ◽  
Pv Panel ◽  
Power Point

DC/DC converters are widely used in photovoltaic (PV) systems to maximize the power drained from solar panels. As the power generated by a PV panel depends on the temperature and irradiance level, a converter needs to constantly modify its input resistance to remain at the maximum power point (MPP). The input resistance of a converter can be described by a simple equation that includes the converter load resistance and the duty cycle of the switching signal. The equation is sufficient for an ideal converter but can lead to incorrect results for a real converter, which naturally features some parasitic resistances. The goal of this study is to evaluate how the parasitic resistances of a converter influence its input resistance and if they are relevant in terms of MPPT system operation.

scholarly journals Analysis and Design of a Multi-Port DC-DC Converter for Interfacing PV Systems

Energies ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1943
Author(s):  
Bader N. Alajmi ◽  
Mostafa I. Marei ◽  
Ibrahim Abdelsalam ◽  
Mohamed F. AlHajri
Keyword(s):  
High Frequency ◽  
Computer Aided Design ◽  
Electromagnetic Transients ◽  
Pv System ◽  
Analysis And Design ◽  
Pv Systems ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Power Point ◽  
Aided Design

A high-frequency multi-port (HFMP) direct current (DC) to DC converter is presented. The proposed HFMP is utilized to interface a photovoltaic (PV) system. The presented HFMP is compact and can perform maximum power point tracking. It consists of a high-frequency transformer with many identical input windings and one output winding. Each input winding is connected to a PV module through an H-bridge inverter, and the maximum PV power is tracked using the perturb and observe (P&O) technique. The output winding is connected to a DC bus through a rectifier. The detailed analysis and operation of the proposed HFMP DC-DC converter are presented. Extensive numerical simulations are conducted, using power system computer aided design (PSCAD)/electromagnetic transients including DC (EMTDC) software, to evaluate the operation and dynamic behavior of the proposed PV interfacing scheme. In addition, an experimental setup is built to verify the performance of the HFMP DC-DC converter.

scholarly journals A Modification of the Perturb and Observe Method to Improve the Energy Harvesting of PV Systems under Partial Shading Conditions

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2521
Author(s):  
Alfredo Gil-Velasco ◽  
Carlos Aguilar-Castillo
Keyword(s):  
Maximum Power ◽  
Global Maximum ◽  
Pv System ◽  
Maximum Power Point ◽  
Partial Shading ◽  
Pv Systems ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Power Point ◽  
Computational Resources

There are multiples conditions that lead to partial shading conditions (PSC) in photovoltaic systems (PV). Under these conditions, the harvested energy decreases in the PV system. The maximum power point tracking (MPPT) controller aims to harvest the greatest amount of energy even under partial shading conditions. The simplest available MPPT algorithms fail on PSC, whereas the complex ones are effective but require high computational resources and experience in this type of systems. This paper presents a new MPPT algorithm that is simple but effective in tracking the global maximum power point even in PSC. The simulation and experimental results show excellent performance of the proposed algorithm. Additionally, a comparison with a previously proposed algorithm is presented. The comparison shows that the proposal in this paper is faster in tracking the maximum power point than complex algorithms.

scholarly journals Different Techniques to Mitigate Partial Shading in Photovoltaic Panels

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3863
Author(s):  
Tiago Alves ◽  
João Paulo N. Torres ◽  
Ricardo A. Marques Lameirinhas ◽  
Carlos A. F. Fernandes
Keyword(s):  
Cell Model ◽  
Research Work ◽  
Experimental Tests ◽  
Operating Conditions ◽  
Pv System ◽  
Partial Shading ◽  
System Architectures ◽  
Pv Systems ◽  
Advantages And Disadvantages ◽  
Pv Panel

The effect of partial shading in photovoltaic (PV) panels is one of the biggest problems regarding power losses in PV systems. When the irradiance pattern throughout a PV panel is inequal, some cells with the possibility of higher power production will produce less and start to deteriorate. The objective of this research work is to present, test and discuss different techniques to help mitigate partial shading in PV panels, observing and commenting the advantages and disadvantages for different PV technologies under different operating conditions. The motivation is to contribute with research, simulation, and experimental work. Several state-of-the-artsolutions to the problem will be presented: different topologies in the interconnection of the panels; different PV system architectures, and also introducing new solution hypotheses, such as different cell interconnections topologies. Alongside, benefits and limitations will be discussed. To obtain actual results, the simulation work was conducted by creating MATLAB/Simulink models for each different technique tested, all centered around the 1M5P PV cell model. The several techniques tested will also take into account different patterns and sizes of partial shading, different PV panel technologies, different values of source irradiation, and different PV array sizes. The results will be discussed and validated by experimental tests.

Maximum Power Point Tracking (MPPT) for a Solar Photovoltaic System: A Review

2015 ◽  
Vol 787 ◽  
pp. 227-232 ◽  
Author(s):  
L.A. Arun Shravan ◽  
D. Ebenezer
Keyword(s):  
Solar Energy ◽  
Maximum Power Point Tracking ◽  
Maximum Power ◽  
Nonlinear Behaviour ◽  
Pv System ◽  
Maximum Power Point ◽  
Pv Systems ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Power Point

In recent years there has been a growing attention towards use of solar energy. Advantages of photovoltaic (PV) systems employed for harnessing solar energy are reduction of greenhouse gas emission, low maintenance costs, fewer limitations with regard to site of installation and absence of mechanical noise arising from moving parts. However, PV systems suffer from relatively low conversion efficiency. Therefore, maximum power point tracking (MPPT) for the solar array is essential in a PV system. The nonlinear behaviour of PV systems as well as variations of the maximum power point with solar irradiance level and temperature complicates the tracking of the maximum power point. This paper reviews various MPPT methods based on three categories: offline, online and hybrid methods. Design of a PV system in a encoding environment has also been reviewed here. Furthermore, different MPPT methods are discussed in terms of the dynamic response of the PV system to variations in temperature and irradiance, attainable efficiency, and implementation considerations.

Maximum Power Point Tracking of Multi-String Photovoltaic Array via Simultaneous Perturbation Stochastic Approximation

2013 ◽  
Author(s):  
Yan Xiao ◽  
Yaoyu Li ◽  
John E. Seem ◽  
Kaushik Rajashekara
Keyword(s):  
Stochastic Approximation ◽  
Maximum Power Point Tracking ◽  
Maximum Power ◽  
Pv System ◽  
Maximum Power Point ◽  
Simultaneous Perturbation Stochastic Approximation ◽  
Pv Systems ◽  
Point Tracking ◽  
Power Point Tracking ◽  
Power Point

This paper presents a Maximum Power Point Tracking (MPPT) strategy for multi-string photovoltaic (PV) systems using the Simultaneous Perturbation Stochastic Approximation (SPSA) algorithm. The multi-string PV system considered is a decentralized control configuration, controlling the voltage reference to each PV module but based on the feedback of the total power at the DC bus. This requires only one pair of voltage and current measurements. The MPPT control problem for such topology of multi-string PV systems features a high input dimension, which can dramatically slow down the searching process for the real-time optimization process involved. The SPSA algorithm is considered in this study due to its remarkable capability of fast convergence for high dimensional search problems endorsed by various applications recently. Simulation study is performed for an 8-string PV system, and experimental study is performed for a 4-string PV system. Good performances are observed for both simulation and experimental results.

scholarly journals DC-link sensorless control strategy for grid-connected PV systems

2021 ◽  
Author(s):  
Mostafa Ahmed ◽  
Mohamed Abdelrahem ◽  
Ahmed Farhan ◽  
Ibrahim Harbi ◽  
Ralph Kennel
Keyword(s):  
Sensorless Control ◽  
Current Loop ◽  
Sensor Failure ◽  
Atmospheric Conditions ◽  
Step Size ◽  
Pv System ◽  
Control Approach ◽  
Control Loops ◽  
Pv Systems ◽  
The Cost

AbstractSensorless strategies become very popular in modern control techniques because they increase the system reliability. Besides, they can be used as back-up control in case of sensor failure. In this paper, a DC-link sensorless control approach is developed, which is suited for grid-connected PV systems. The studied system is a two-stage PV scheme, where the DC–DC stage (boost converter) is controlled using an adaptive step-size perturb and observe (P&O) method. Further, the inverter control is accomplished by voltage oriented control (VOC). Generally, the VOC is implemented with two cascaded control loops, namely an outer voltage loop and an inner current loop. However, in this work, the outer loop is avoided and the reference current is generated using a losses model for the system. The losses model accounts for the most significant losses in the PV system. Moreover, particle swarm optimization (PSO) is utilized to compensate for the unmodeled losses. The PSO is executed offline for the purpose of calculation burden reduction. The proposed approach simplifies the cascaded VOC strategy and eliminates the DC-link voltage sensor, which in turn decreases the cost of the system. Finally, the proposed technique is compared with the conventional one at different atmospheric conditions and validated using MATLAB simulation results.

Sign in / Sign up

Export Citation Format

Share Document