Optimal Machining Parameters for Achieving Minimal Tool Wear in Turning Of GFRP Composites

2004 ◽  
Vol 6 (3) ◽  
pp. 119-128 ◽  
Author(s):  
K. Palanikumar, ◽  
L. Karunamoorthy, ◽  
R. Karthikeyan,
Keyword(s):  
Tool Wear ◽  
Machining Parameters ◽  
Gfrp Composites

Multiresponse Optimization of Al Alloy-SiC Composite Machining Parameters for Minimum Tool Wear and Maximum Metal Removal Rate

2013 ◽  
Vol 135 (2) ◽  
Author(s):  
Rajesh Kumar Bhushan
Keyword(s):  
Tool Wear ◽  
Metal Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Al Alloy ◽  
Machining Parameters ◽  
Metal Removal Rate ◽  
Nose Radius ◽  
Multiresponse Optimization

Optimization in turning means determination of the optimal set of the machining parameters to satisfy the objectives within the operational constraints. These objectives may be the minimum tool wear, the maximum metal removal rate (MRR), or any weighted combination of both. The main machining parameters which are considered as variables of the optimization are the cutting speed, feed rate, depth of cut, and nose radius. The optimum set of these four input parameters is determined for a particular job-tool combination of 7075Al alloy-15 wt. % SiC (20–40 μm) composite and tungsten carbide tool during a single-pass turning which minimizes the tool wear and maximizes the metal removal rate. The regression models, developed for the minimum tool wear and the maximum MRR were used for finding the multiresponse optimization solutions. To obtain a trade-off between the tool wear and MRR the, a method for simultaneous optimization of the multiple responses based on an overall desirability function was used. The research deals with the optimization of multiple surface roughness parameters along with MRR in search of an optimal parametric combination (favorable process environment) capable of producing desired surface quality of the turned product in a relatively lesser time (enhancement in productivity). The multi-objective optimization resulted in a cutting speed of 210 m/min, a feed of 0.16 mm/rev, a depth of cut of 0.42 mm, and a nose radius of 0.40 mm. These machining conditions are expected to respond with the minimum tool wear and maximum the MRR, which correspond to a satisfactory overall desirability.

scholarly journals Machinability Study of Hybrid Nanoclay-Glass Fibre Reinforced Polyester Composites

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
P. Prabhu ◽  
P. Jawahar ◽  
M. Balasubramanian ◽  
T. P. Mohan
Keyword(s):  
Tool Wear ◽  
Glass Fibre ◽  
Microstructural Analysis ◽  
Process Parameter ◽  
Optimum Process ◽  
Machining Parameters ◽  
Twist Drill ◽  
End Mill ◽  
Glass Fibre Reinforced ◽  
Polyester Composites

Glass fibre reinforced polyester composites (GRP) and hybrid nanoclay and glass fibre reinforced polyester nanocomposites (CGRP) are fabricated by vacuum assisted resin infusion technique. The optimum mechanical properties are obtained for CGRP with 3 wt.% nanoclay. Three types of drills (carbide twist drill D 5407060, HSS twist drill BS-328, and HSS end mill (4 flutes “N”-type end mill RH-helical flute)) of 6 mm diameters are used to drill holes on GRP and CGRP. Three different speeds (600, 852, and 1260 rpm) and two different feeds (0.045, 0.1 mm/rev) are selected as process parameters. The effect of process parameter on thrust force and delamination during drilling CGRP is analyzed for optimizing the machining parameters. The delamination factor is low for the optimum process parameter (feed = 0.1 mm/rev and speed 852 rpm). Microstructural analysis confirms that at higher feeds, delamination is low for CGRP drilled with carbide tools. In order to analyze the effect of nanoclay in CGRP on tool wear, 200 holes were drilled on CGRP samples with 3 wt.% nanoclay, and the tool wear is analyzed under optimized parametric condition. Tool wear is high in HSS twist drill compared with carbide drill. The presence of nanoclay also accelerates the tool wear.

Machining

2013 ◽  
pp. 213-270
Keyword(s):  
Electron Beam ◽  
Tool Wear ◽  
Electrical Discharge ◽  
Cutting Fluids ◽  
Machining Parameters ◽  
Machining Processes ◽  
Wire Cutting ◽  
Grinding Operations ◽  
Conventional Machining

Abstract This chapter covers the practical aspects of machining, particularly for turning, milling, drilling, and grinding operations. It begins with a discussion on machinability and its impact on quality and cost. It then describes the dimensional and surface finish tolerances that can be achieved through conventional machining methods, the mechanics of chip formation, the factors that affect tool wear, the selection and use of cutting fluids, and the determination of machining parameters based on force and power requirements. It also includes information on nontraditional machining processes such as electrical discharge, abrasive jet, and hydrodynamic machining, laser and electron beam machining, ultrasonic impact grinding, and electrical discharge wire cutting.

scholarly journals Simulation and Experimental Study on the Surface Generation Mechanism of Cu Alloys in Ultra-Precision Diamond Turning

Micromachines ◽  
2019 ◽  
Vol 10 (9) ◽  
pp. 573
Author(s):  
Zhang ◽  
Guo ◽  
Chen ◽  
Fu ◽  
Zhao
Keyword(s):  
Tool Wear ◽  
Diamond Tool ◽  
Surface Characteristics ◽  
Diamond Turning ◽  
Generation Mechanism ◽  
Surface Generation ◽  
Machining Parameters ◽  
Nose Radius ◽  
Cu Alloys ◽  
Ultra Precision

The surface generation mechanism of the Cu alloys in ultra-precision diamond turning is investigated by both simulation and experimental methods, where the effects of the cutting parameters on the surface characteristics are explored, including the workpiece spindle speed, the cutting depth, the feed rate and the nose radius of the diamond tool. To verify the built model, the cutting experiments are conducted at selected parameters, where the causes of the error between the simulation and the machining results are analyzed, including the effects of the materials microstructure and the diamond tool wear. In addition, the nanometric surface characteristics of the Cu alloys after the diamond turning are identified, including the finer scratching grooves caused by the tool wear, the formation of the surface burs and the adhesion of graphite. The results show that the built model can be basically used to predict the surface topography for the selection of the appropriate machining parameters in the ultra-precision diamond turning process.

scholarly journals Findings of performance evaluation of EDM for different materials of electrodes and work pieces- a review

2018 ◽  
Vol 7 (4.5) ◽  
pp. 542
Author(s):  
Harshalkumar R. Mundane ◽  
Dr. A. V. Kale ◽  
Dr. J. P. Giri
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Performance Measure ◽  
Machining Process ◽  
Machining Parameters ◽  
Spark Erosion ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Off Time ◽  
Time Pulse

EDM (Spark erosion) is non-conventional machining process which uses as removing unwanted material by electrical spark erosion. EDM Machining parameters affecting to the performance and the industries goal is to produce high quality of product with less time consuming and cost. To achieve these goals, optimizing the machining parameters such as pulse on time, pulse off time, cutting speed, depth of cut, duty cycle, arc gap, voltage etc. The performance measure of EDM is calculated on the basis of Material Remove Rate(MRR), Tool Wear Rate(TWR), and Surface Roughness(SR).The main objective of present work is to investigate of the influence of input EDM (Electro Discharge Machining) parameters on machining characteristics like surface roughness and the effects of various EDM process parameters such as pulse on time, pulse off time, servo voltage, peak current, dielectric flow rate, on different process response parameters such as material removal rate (MRR), surface roughness (Ra), Kerf (width of Cut), tool wear ratio(TWR)and surface integrity factors. In this paper few selected research paper related to Die-sinker EDM with effect of MRR, TWR, surface roughness (SR) and work piece material have been discussed.   

scholarly journals Experimental Study on Tool Wear and Delamination in Milling CFRPs with TiAlN- and TiN-Coated Tools

Coatings ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 623 ◽  
Author(s):  
Dervis Ozkan ◽  
Peter Panjan ◽  
Mustafa Sabri Gok ◽  
Abdullah Cahit Karaoglanli
Keyword(s):  
Tool Wear ◽  
Cutting Tool ◽  
Failure Mechanisms ◽  
Cutting Tools ◽  
Machining Process ◽  
Dynamic Loads ◽  
Fiber Reinforced Polymers ◽  
Machining Parameters ◽  
Coated Tool ◽  
Cfrp Composite

Carbon fiber-reinforced polymers (CFRPs) have very good mechanical properties, such as extremely high tensile strength/weight ratios, tensile modulus/weight ratios, and high strengths. CFRP composites need to be machined with a suitable cutting tool; otherwise, the machining quality may be reduced, and failures often occur. However, as a result of the high hardness and low thermal conductivity of CFRPs, the cutting tools used in the milling process of these materials complete their lifetime in a short cycle, due to especially abrasive wear and related failure mechanisms. As a result of tool wear, some problems, such as delamination, fiber breakage, uncut fiber and thermal damage, emerge in CFRP composite under working conditions. As one of the main failure mechanisms emerging in the milling of CFRPs, delamination is primarily affected by the cutting tool material and geometry, machining parameters, and the dynamic loads arising during the machining process. Dynamic loads can lead to the breakage and/or wear of cutting tools in the milling of difficult-to-machine CFRPs. The present research was carried out to understand the influence of different machining parameters on tool abrasion, and the work piece damage mechanisms during CFRP milling are experimentally investigated. For this purpose, cutting tests were carried out using a (Physical Vapor Deposition) PVD-coated single layer TiAlN and TiN carbide tool, and the abrasion behavior of the coated tool was investigated under dry machining. To understand the wear process, scanning electron microscopy (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS) was used. As a result of the experiments, it was determined that the hard and abrasive structure of the carbon fibers caused flank wear on TiAlN- and TiN-coated cutting tools. The best machining parameters in terms of the delamination damage of the CFRP composite were obtained at high cutting speeds and low feed rates. It was found that the higher wear values were observed at the TiAlN-coated tool, at the feed rate of 0.05 mm/tooth.

Sign in / Sign up

Export Citation Format

Share Document