scholarly journals Investigation of the optimal design of orthodontic mini-implants based on the primary stability: A finite element analysis

2019 ◽  
Vol 13 (2) ◽  
pp. 85-89 ◽  
Author(s):  
Amir Hooman Sadr Haghighi ◽  
Vahid Pouyafar ◽  
Ali Navid ◽  
Mahsa Eskandarinezhad ◽  
Tannaz Abdollahzadeh Baghaei
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Primary Stability ◽  
Implant Design ◽  
Element Analysis ◽  
Taper Angle ◽  
Mini Implants ◽  
The Impact ◽  
Taguchi’S Design Of Experiments ◽  
Design Factors

Background. The design of an orthodontic mini-implant is a significant factor in determining its primary stability and its clinical success. The aim of this study was to measure the relative effect of mini-implant design factors on primary stability of orthodontic mini-implants. Methods. Thirty-two 3-dimensional assemblies of mini-implant models with their surrounding bone were generated using finite element analysis software. The maximum displacement of each mini-implant model was measured as they were loaded with a 2-N horizontal force. Employing Taguchi’s design of experiments as a statistical method, the contribution of each design factor to primary stability was calculated. As a result of the great effect of the upper diameter and length, to better detect the impact of the remaining design factors, another set of 25 models with a fixed amount of length and diameter was generated and evaluated. Results. The diameter and length showed a great impact on the primary stability in the first set of experiments (P<0.05). According to the second set of experiments, increased taper angle in the threaded and non-threaded area decreased the primary stability. There was also an optimum amount of 2.5 mm for threaded taper length beyond which the primary stability decreased. Conclusion. It is advisable to increase the diameter and length if primary stability is at risk. In the second place, a minimum amount of taper angle, both in the threaded and non-threaded area with an approximate proportion of 20% of threaded taper length to MI length, would be desirable for MIs with a moderate size.

Comparison of Stress Distribution in Surrounding Bone during Insertion of Dental Implants on Four Implant Threads under the Effect of an Impact: A Finite Element Study

2022 ◽  
Vol 54 ◽  
pp. 89-101
Author(s):  
Noureddine Djebbar ◽  
Abdessamed Bachiri ◽  
Benali Boutabout
Keyword(s):  
Finite Element ◽  
Stress Distribution ◽  
Load Transfer ◽  
Three Dimensional ◽  
Primary Stability ◽  
Implant Design ◽  
Element Analysis ◽  
Three Dimensional Finite Element ◽  
The Impact ◽  
Surrounding Bone

The design of an implant thread plays a fundamental role in the osseointegration process, particularly in low-density bone. It has been postulated that design features that maximize the surface area available for contact may improve mechanical anchorage and stability in cancellous bone. The primary stability of a dental implant is determined by the mechanical engagement between the implant and bone at the time of implant insertion. The contact area of implant-bone interfaces and the concentrated stresses on the marginal bones are principal concerns of implant designers. Numerous factors influence load transfer at the bone-implant interface, for example, the type of loading, surface structure, amount of surrounding bone, material properties of the implant and implant design. The purpose of this study was to investigate the effects of the impact two different projectile of implant threads on stress distribution in the jawbone using three-dimensional finite element analysis.

scholarly journals Biomechanical Behavior of Bioactive Material in Dental Implant: A Three-Dimensional Finite Element Analysis

2020 ◽  
Vol 2020 ◽  
pp. 1-9
Author(s):  
Vathsala Patil ◽  
Nithesh Naik ◽  
Srikanth Gadicherla ◽  
Komal Smriti ◽  
Adithya Raju ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Graphene Oxide ◽  
Titanium Implant ◽  
Von Mises Stress ◽  
Implant Design ◽  
Element Analysis ◽  
Von Mises ◽  
Implant System ◽  
The Impact

Dental implants are widely accepted for the rehabilitation of missing teeth due to their aesthetic compliance, functional ability, and great survival rate. The various components in implant design like thread design, thread angle, pitch, and material used for manufacturing play a critical role in its success. Understanding these influencing factors and implementing them properly in implant design can reduce cases of potential implant failure. Recently, finite element analysis (FEA) is being widely used in the field of health sciences to solve problems in designing medical devices. It provides valid and accurate assessment in the clinical and in vitro analysis. Hence, this study was conducted to evaluate the impact of thread design of the implant and 3 different bioactive materials, titanium alloy, graphene, and reduced graphene oxide (rGO) on stress, strain, and deformation in the implant system using FEA. In this study, the FEA model of the bones and the tissues are modeled as homogeneous, isotropic, and linearly elastic material with a titanium implant system with an assumption of it 100% osseointegrated into the bone. The titanium was functionalized with graphene and graphene oxide. A modeling software tool Catia® and Ansys Workbench® is used to perform the analysis and evaluate the von Mises stress distribution, strain, and deformation at the implant and implant-cortical bone interface. The results showed that the titanium implant with a surface coating of graphene oxide exhibited better mechanical behavior than graphene, with mean von Mises stress of 39.64 MPa in pitch 1, 23.65 MPa in pitch 2, and 37.23 MPa in pitch 3. It also revealed that functionalizing the titanium implant will help in reducing the stress at the implant system. Overall, the study emphasizes the use of FEA analysis methods in solving various biomechanical issues about medical and dental devices, which can further open up for invivo study and their practical uses.

scholarly journals Experimental & FEM Analysis of Orthodontic Mini-Implant Design on Primary Stability

2021 ◽  
Vol 11 (12) ◽  
pp. 5461
Author(s):  
Elmedin Mešić ◽  
Enis Muratović ◽  
Lejla Redžepagić-Vražalica ◽  
Nedim Pervan ◽  
Adis J. Muminović ◽  
...  
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Primary Stability ◽  
Fem Analysis ◽  
Implant Design ◽  
Special Focus ◽  
Engineering System ◽  
Mini Implants ◽  
Pull Out ◽  
Computer Aided

The main objective of this research is to establish a connection between orthodontic mini-implant design, pull-out force and primary stability by comparing two commercial mini-implants or temporary anchorage devices, Tomas®-pin and Perfect Anchor. Mini-implant geometric analysis and quantification of bone characteristics are performed, whereupon experimental in vitro pull-out test is conducted. With the use of the CATIA (Computer Aided Three-dimensional Interactive Application) CAD (Computer Aided Design)/CAM (Computer Aided Manufacturing)/CAE (Computer Aided Engineering) system, 3D (Three-dimensional) geometric models of mini-implants and bone segments are created. Afterwards, those same models are imported into Abaqus software, where finite element models are generated with a special focus on material properties, boundary conditions and interactions. FEM (Finite Element Method) analysis is used to simulate the pull-out test. Then, the results of the structural analysis are compared with the experimental results. The FEM analysis results contain information about maximum stresses on implant–bone system caused due to the pull-out force. It is determined that the core diameter of a screw thread and conicity are the main factors of the mini-implant design that have a direct impact on primary stability. Additionally, stresses generated on the Tomas®-pin model are lower than stresses on Perfect Anchor, even though Tomas®-pin endures greater pull-out forces, the implant system with implemented Tomas®-pin still represents a more stressed system due to the uniform distribution of stresses with bigger values.

Flexible Flowline Walking Tendency on Seabed With Longitudinal Undulations and Transverse Gradients

2018 ◽  
Author(s):  
Graeme Roberts ◽  
T. Sriskandarajah ◽  
Gianluca Colonnelli ◽  
Arnaud Roux ◽  
Alan Roy ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Temperature Gradients ◽  
Radius Of Curvature ◽  
Bend Radius ◽  
Lateral Buckling ◽  
Element Analysis ◽  
Slip Tendency ◽  
Start Ups ◽  
The Impact

A method of carrying out a combined axial walking and lateral buckling assessment for a flexible flowline has been developed using finite element analysis. The method overcomes limitations of screening assessments which could be inconclusive when applied either to a flexible flowline on an undulating seabed with transverse gradients or to one that buckles during hydrotest. Flexible flowlines that were to be surface-laid on a seabed with longitudinal undulations and transverse gradients were assessed using the method. The flexible flowlines were simulated in their as-laid state, and the simulation incorporated hydrotest pressure and the pressure & temperature gradients and transients associated with multiple start-ups. The objective was to quantify the axial walking and lateral slip tendency of the flexible flowlines and the impact that walking might have on the connected end structures. The lateral buckle locations predicted by finite element analysis were compared to a post-hydrotest survey and the radius of curvature from analysis was compared to the minimum bend radius of the flexible.

scholarly journals Finite Element Analysis-Aided Performance Improvement of Circular Coil Assemblies Applied in Electric Vehicle Inductive Chargers

2021 ◽  
Author(s):  
Guodong Zhu ◽  
Dawei Gao
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Electric Vehicle ◽  
Performance Improvement ◽  
Magnetic Circuit ◽  
Element Analysis ◽  
System Parameters ◽  
Leakage Magnetic Field ◽  
Fea Simulation ◽  
The Impact

Energy efficiency and leakage magnetic field (LMF) are two important issues in inductive chargers. In this work, the maximum achievable coil efficiency and the corresponding LMF strength are formulated as functions of system parameters, and figure of merits (FOM) are proposed for assessing the efficiency and LMF performance of the coil assemblies. The target application is electric vehicle inductive chargers where the LMF is suppressed via passive shielding. The impact of the coil assembly’s geometric parameters on both FOMs is examined through a combination of finite element analysis (FEA) simulation and magnetic circuit analysis, and measures to improve the FOMs are studied Optimization of an exemplary coil assembly within given dimensional limits is conducted and the performance improvement is verified by FEA simulation results. <br>

scholarly journals Simulation and Analysis of Fluid-Solid Coupling of Wave Impact Sandcastle Based on COMSOL

2020 ◽  
Vol 3 (1) ◽  
Author(s):  
Zhen Ouyang ◽  
Ke Wang ◽  
Zihao Yu ◽  
Kaikai Xu ◽  
Qianyu Zhao ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Simulation Analysis ◽  
Coupling Model ◽  
Complex Problem ◽  
Wave Impact ◽  
Element Analysis ◽  
Quantitative Calculation ◽  
The Finite Element Analysis ◽  
The Impact

It is a complex problem to study the interaction between sand castle and flowing water, which needs to consider the complexity of seawater flow and the stress of sand castle structure. The authors use the fluid-solid coupling model to establish the connection between the fluid field and the structural mechanical field, and use the finite element analysis to complete the simulation modeling of the transient process of wave impact and sandcastle foundation deformation. This paper analyzes the stress and the first principal strain of the sand castle foundation in the direction of flow velocity when the sand castle foundation is hit by waves, as a method to judge the strength of the sand castle.The best shape: the boundary value of sand castle collapse caused by strain have been determined, so as to obtain the maximum stress that a sand castle foundation can bear before collapse, which makes it possible to use the fatigue strength calculation theory of sand castle solid to carry out the quantitative calculation of sand castle durability. At the same time, the impact of waves is abstracted as wave motion equation. Finally, the finite element analysis technology is adopted to calculate the main strain of sandcastles of different shapes under the impact of the same wave, and through the comparison of the main strain, the authors get the sandcastle shape with the strongest anti-wave impact ability, which is the eccentric circular platform body.Affected by rain: the authors considered the effect of rainwater infiltration on the sandcastle's stress, and simplified the process of rain as a continuous and uniform infiltration of rain into the sandcastle's surface. The rain changes the gravity of the sand on the castle's surface. Simulation analysis is adopted to calculate the surface stress of sand castle with different degree of water seepage and different geometry. By comparison, it has been found that the smooth cone is more able to withstand the infiltration of rain without collapse. 

Finite Element Analysis for Shock Resistance Evaluation of Cushion-Packaged Multifunction Printer Considering Internal Modules

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Se-Chang Kim ◽  
Dae-Geun Cho ◽  
Tae-Gyu Kim ◽  
Se-Hun Jung ◽  
Ja-Choon Koo ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Shock Acceleration ◽  
External Shocks ◽  
Compression Tests ◽  
Element Analysis ◽  
Dynamic Behaviors ◽  
Shock Resistance ◽  
The Impact ◽  
Multifunction Printer

Failures in IT electronics are often caused by falling or external shocks during transportation. These failures cause customers to mistrust the reliability of the products. Many manufacturers of IT electronics have not only used cushioning materials but also increased the shock resistance of their products for failure prevention. Especially in case of printer products, the design of the packaging and the product robustness are extremely important because of their substantial weight and the fragility of the internal modules. For product design, it is essential to understand the impact failure mechanism of the products. In this study, a compression test, a drop impact test, and a finite element analysis (FEA) were performed to analyze the dynamic behaviors of a packaged multifunction printer (MFP). The mechanical properties of a cushioning material were measured by compression tests. The FE models of the cushion packaging and the MFP included the physical characteristics of the internal modules, and their dynamic behaviors were obtained using the commercial software ls-dyna3d. Simulation results were also compared with drop test results to verify the proposed FE models. The shock resistance of the MFP was assessed by stress analysis and strength evaluation. We also expect our FE models will be useful for evaluating the fragility of the internal modules because the models can numerically estimate the shock acceleration profiles of the internal modules, which are difficult to measure experimentally.

Sign in / Sign up

Export Citation Format

Share Document