Advanced β-Solidifying Titanium Aluminides – Development Status and Perspectives

2013 ◽  
Vol 1516 ◽  
pp. 3-16 ◽  
Author(s):  
Helmut Clemens ◽  
Martin Schloffer ◽  
Emanuel Schwaighofer ◽  
Robert Werner ◽  
Andrea Gaitzenauer ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Room Temperature ◽  
Titanium Aluminides ◽  
Aircraft Engine ◽  
High Energy ◽  
Heat Treatments ◽  
Mechanical Processing ◽  
Tial Alloys ◽  
Precision Casting

ABSTRACTAfter almost three decades of intensive fundamental research and development activities intermetallic titanium aluminides based on the -TiAl phase have found applications in automotive and aircraft engine industries. The advantages of this class of innovative high-temperature materials are their low density as well as their good strength and creep properties up to 750°C. A drawback, however, is their limited ductility at room temperature, which is reflected by a low plastic strain at fracture. This behavior can be attributed to a limited dislocation movement along with microstructural inhomogeneity. Advanced TiAl alloys, such as β-solidifying TNM™ alloys, are complex multi-phase materials which can be processed by ingot or powder metallurgy as well as precision casting methods. Each production process leads to specific microstructures which can be altered and optimized by thermo-mechanical processing and/or subsequent heat-treatments. The background of these heat-treatments is at least twofold, i.e. concurrent increase of ductility at room temperature and creep strength at elevated temperature. In order to achieve this goal the knowledge of the occurring solidification processes and phase transformation sequences is essential. Therefore, thermodynamic calculations were conducted to predict phase fraction diagrams of engineering TiAl alloys. After experimental verification, these phase diagrams provided the base for the development of heat treatments to adjust balanced mechanical properties. To determine the influence of deformation and kinetic aspects, sophisticated ex- and in-situ methods have been employed to investigate the evolution of the microstructure during thermo-mechanical processing and subsequent multi-step heat-treatments. For example, in-situ high-energy X-ray diffraction was conducted to study dynamic recovery and recrystallization processes during hot-deformation tests. Summarizing all results a consistent picture regarding microstructure formation and its impact on mechanical properties in TNM alloys can be given.

The Use of In Situ Characterization Techniques for the Development of Intermetallic Titanium Aluminides

2014 ◽  
Vol 783-786 ◽  
pp. 2097-2102 ◽  
Author(s):  
Svea Mayer ◽  
Emanuel Schwaighofer ◽  
Martin Schloffer ◽  
Helmut Clemens
Keyword(s):  
Titanium Aluminides ◽  
Turbine Blades ◽  
Heat Treatments ◽  
Mechanical Processing ◽  
Tial Alloys ◽  
Solidification Processes ◽  
Consistent Picture ◽  
Aero Engines ◽  
Multi Phase

Urgent needs concerning energy efficiency and environmental politics require novel approaches to materials design. One recent example is thereby the implementation of light-weight intermetallic titanium aluminides as structural materials for the application in turbine blades of aero-engines as well as in turbocharger turbine wheels for the next generation of automotive engines. Each production process leads to specific microstructures which can be altered and optimized by thermo-mechanical processing and / or subsequent heat-treatments. To develop sound and sustainable processing routes, knowledge on solidification processes and phase transformation sequences in advanced TiAl alloys is fundamental. Therefore, in-situ diffraction techniques employing synchrotron radiation and neutrons were used for establishing phase fraction diagrams, investigating advanced heat-treatments as well as for optimizing thermo-mechanical processing. Summarizing all results a consistent picture regarding microstructure formation and its impact on mechanical properties in advanced multi-phase TiAl alloys can be given.

Development Status, Applications and Perspectives of Advanced Intermetallic Titanium Aluminides

2014 ◽  
Vol 783-786 ◽  
pp. 15-20 ◽  
Author(s):  
Helmut Clemens ◽  
Svea Mayer
Keyword(s):  
Titanium Aluminides ◽  
Heat Treatments ◽  
Tial Alloys ◽  
Creep Properties ◽  
Automotive Engine ◽  
Precision Casting ◽  
High Temperature Materials ◽  
Engine Industry ◽  
Fundamental Research ◽  
Multi Phase

After almost three decades of intensive fundamental research and development activities, intermetallic titanium aluminides based on the ordered γ-TiAl phase have found applications in aircraft and automotive engine industry. The advantages of this class of innovative high-temperature materials are their low density and their good strength and creep properties up to 750°C as well as their good oxidation and burn resistance. Advanced TiAl alloys are complex multi-phase alloys which can be processed by ingot or powder metallurgy as well as precision casting methods. Each process leads to specific microstructures which can be altered and optimized by thermo-mechanical processing and/or subsequent heat treatments. The background of these heat treatments is at least twofold, i.e. concurrent increase of ductility at room temperature and creep strength at elevated temperature.

Mechanical properties of NiAl-Mo composites produced by specially controlled directional solidification

2012 ◽  
Vol 1516 ◽  
pp. 255-260 ◽  
Author(s):  
G. Zhang ◽  
L. Hu ◽  
W. Hu ◽  
G. Gottstein ◽  
S. Bogner ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Directional Solidification ◽  
Creep Resistance ◽  
Room Temperature ◽  
Growth Direction ◽  
Nominal Composition ◽  
Potential Candidate ◽  
In Situ Composites

ABSTRACTMo fiber reinforced NiAl in-situ composites with a nominal composition Ni-43.8Al-9.5Mo (at.%) were produced by specially controlled directional solidification (DS) using a laboratory-scale Bridgman furnace equipped with a liquid metal cooling (LMC) device. In these composites, single crystalline Mo fibers were precipitated out through eutectic reaction and aligned parallel to the growth direction of the ingot. Mechanical properties, i.e. the creep resistance at high temperatures (HT, between 900 °C and 1200 °C) and the fracture toughness at room temperature (RT) of in-situ NiAl-Mo composites, were characterized by tensile creep (along the growth direction) and flexure (four-point bending, vertical to the growth direction) tests, respectively. In the current study, a steady creep rate of 10-6s-1 at 1100 °C under an initial applied tensile stress of 150MPa was measured. The flexure tests sustained a fracture toughness of 14.5 MPa·m1/2at room temperature. Compared to binary NiAl and other NiAl alloys, these properties showed a remarkably improvement in creep resistance at HT and fracture toughness at RT that makes this composite a potential candidate material for structural application at the temperatures above 1000 °C. The mechanisms responsible for the improvement of the mechanical properties in NiAl-Mo in-situ composites were discussed based on the investigation results.

Influence of Heat Treatment on Microstructure and Mechanical Properties of Selective Laser Melted TiAl6V4 Alloy

2018 ◽  
Vol 284 ◽  
pp. 615-620 ◽  
Author(s):  
R.M. Baitimerov ◽  
P.A. Lykov ◽  
L.V. Radionova
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Selective Laser Melting ◽  
Room Temperature ◽  
Base Alloy ◽  
Tensile Tests ◽  
Heat Treatments ◽  
Laser Melting ◽  
Microstructure And Mechanical Properties ◽  
Treatment Procedures

TiAl6V4 titanium base alloy is widely used in aerospace and medical industries. Specimens for tensile tests from TiAl6V4 with porosity less than 0.5% was fabricated by selective laser melting (SLM). Specimens were treated using two heat treatment procedures, third batch of specimens was tested in as-fabricated statement after machining. Tensile tests were carried out at room temperature. Microstructure and mechanical properties of SLM fabricated TiAl6V4 after different heat treatments were investigated.

Effects of a pre-anneal on the mechanical properties of γ-TiAl

2000 ◽  
Vol 646 ◽  
Author(s):  
Fabienne Grégori ◽  
Philippe Penhoud ◽  
Patrick Veyssière
Keyword(s):  
Mechanical Properties ◽  
Yield Stress ◽  
Alloy Composition ◽  
Heat Treatments ◽  
Tial Alloys ◽  
Clear Effect ◽  
Interstitial Atoms

ABSTRACTThe temperature, TP, and the stress, σP, at which the yield stress of γ-TiAl alloys peaks are influenced by factors such as alloy composition and load orientation. Available data indicates that in the absence of adequate heat treatments, TP and σP are shifted towards values significantly higher than those of samples pre-annealed in order to precipitate interstitial atoms. Conditions under which precipitation influences the anomalous regime are revealed by dedicated tests. In addition to pointing out the clear effect of interstitials, these tests suggest that further ordering may contribute to the strength of Al-rich γ-TiAl.

scholarly journals In-Situ Characterization by High-Energy X-ray Diffraction of the Phase Transformations Leading to Transformation-Induced Plasticity-Aided Bainitic Steel

2019 ◽  
Vol 3 (4) ◽  
pp. 25
Author(s):  
Zélie Tournoud ◽  
Frédéric De Geuser ◽  
Gilles Renou ◽  
Didier Huin ◽  
Patricia Donnadieu ◽  
...  
Keyword(s):  
Carbon Content ◽  
Phase Transformations ◽  
High Energy ◽  
Heat Treatments ◽  
Treatment Temperature ◽  
Bainitic Steel ◽  
X Ray Diffraction ◽  
Transformation Induced Plasticity ◽  
X Ray

The phase transformations occurring during the heat treatments leading to transformation-induced plasticity (TRIP)-aided bainitic steel have been investigated in-situ by high-energy X-ray diffraction (HEXRD) conducted with synchrotron light at 90 keV. Direct microstructure characterization has been performed by electron microscopy using electron backscatter diffraction and orientation and phase mapping in a transmission electron microscope. HEXRD data allow the quantification of the evolution of the austenite phase fraction with the heat treatments, as well as its carbon content and the fraction of carbides, from the lattice parameter evolution. It is shown that different combinations of austenite fraction and carbon content can be reached by adjusting the heat treatment temperature.

scholarly journals Wide-Gap Brazing of K417G Alloy Assisted by In Situ Precipitation of M3B2 Boride Particles

Materials ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3140 ◽  
Author(s):  
Zhun Cheng ◽  
Xiaoqiang Li ◽  
Minai Zhang ◽  
Shengguan Qu ◽  
Huiyun Li
Keyword(s):  
Mechanical Properties ◽  
Powder Metallurgy ◽  
Room Temperature ◽  
Distribution Characteristics ◽  
Powder Metallurgy Technique ◽  
Dispersion Strengthening ◽  
Eutectic Transformation ◽  
Wide Gap ◽  
Strength And Plasticity

In this study, K417G Ni-based superalloy with a 20-mm gap was successfully bonded at 1200 °C using powder metallurgy with a powder mixture. The results indicated that the microstructure and mechanical properties of the as-bonded alloy were highly dependent on the brazing time (15–45 min), mainly due to the precipitation and distribution characteristics of M3B2 boride particles. Specifically, alloy brazed for 30 min exhibited desirable mechanical properties, such as a high tensile ultimate strength of 971 MPa and an elongation at fracture of 6.5% at room temperature, exceeding the balance value (935 MPa) of the base metal. The excellent strength and plasticity were mainly due to coherent strengthening and dispersion strengthening of the in situ spherical and equiaxed M3B2 boride particles in the γ + γ′ matrix. In addition, the disappearance of dendrites and the homogenization of the microstructure are other factors that cannot be excluded. This powder metallurgy technique, which can avoid the eutectic transformation of traditional brazing, provides a new effective method for wide-gap repair of alloy materials.

Sign in / Sign up

Export Citation Format

Share Document