Optical investigations on sputtered CuCl thin films

2005 ◽  
Vol 891 ◽  
Author(s):  
Gomathi Natarajan ◽  
Anirban Mitra ◽  
Lisa O'Reilly ◽  
Stephen Daniels ◽  
David C. Cameron ◽  
...  
Keyword(s):  
Thin Films ◽  
Room Temperature ◽  
Free Exciton ◽  
Ultra Violet ◽  
Rf Magnetron Sputtering ◽  
Potential Candidate ◽  
X Ray Diffraction ◽  
Optical Absorbance ◽  
Uv Emission ◽  
Silicon Device

ABSTRACTCopper (I) chloride (CuCl) is a potential candidate for ultra violet optoelectronics due to the fact that it is closely lattice matched with silicon, which makes it readily integrable with silicon device technology. The structural and optoelectronic properties of CuCl thin films deposited by RF magnetron sputtering are investigated. The crystallinity is studied using X-ray diffraction which confirms the growth of CuCl thin films with cubic zinc blende structure predominantly orientated in <111> direction. Excitonic transitions in the thin films were thoroughly investigated using optical absorbance and luminescence spectroscopies. Room temperature absorption spectroscopic analysis confirms the existence of two exciton peaks namely Z12 and Z3 at 372 and 380 nm respectively. A strong UV emission is observed at room temperature in cathodoluminescence and photoluminescence spectra due to the recombination of Z3 exciton at approximately 384 nm. In the low temperature photoluminescence spectrum, a free exciton (Z3) and a bound exciton (I1) are observed. A variation of 1.3 nm to 10 nm was observed in the Z3 exciton line width from 10 K to 300 K.

Reactive Sputtering Growth and Characterizations of InN Thin Films on Si Substrates

2012 ◽  
Vol 545 ◽  
pp. 290-293
Author(s):  
Maryam Amirhoseiny ◽  
Hassan Zainuriah ◽  
Ng Shashiong ◽  
Mohd Anas Ahmad
Keyword(s):  
Thin Films ◽  
Room Temperature ◽  
Rf Magnetron Sputtering ◽  
Rf Power ◽  
X Ray Diffraction ◽  
Nitrogen Gas ◽  
X Ray ◽  
Force Microscopy ◽  
Si Substrates ◽  
Atomic Force

We have studied the effects of deposition conditions on the crystal structure of InN films deposited on Si substrate. InN thin films have been deposited on Si(100) substrates by reactive radio frequency (RF) magnetron sputtering method with pure In target at room temperature. The nitrogen gas pressure, applied RF power and the distance between target and substrate were 2×10-2 Torr, 60 W and 8 cm, respectively. The effects of the Ar–N2 sputtering gas mixture on the structural properties of the films were investigated by using scanning electron microscope, energy-dispersive X-ray spectroscopy, atomic force microscopy and X-ray diffraction techniques.

The Origin of Luminescence From Cerium Oxide on Silicon

1999 ◽  
Vol 560 ◽  
Author(s):  
Won Chel Choiv ◽  
Ho Nyung Lee ◽  
Yong Kim ◽  
Eun Kyu Kim
Keyword(s):  
Thin Films ◽  
Thermal Treatment ◽  
Cerium Oxide ◽  
Cerium Dioxide ◽  
Room Temperature ◽  
Ultra Violet ◽  
Blue Luminescence ◽  
Luminescent Material ◽  
Uv Emission ◽  
Thermally Treated

ABSTRACTAs the ultra-violet/blue luminescent material, we will introduce the thermal treated cerium oxide on silicon. It has been confirmed a violet/blue luminescence ranging from 358 rim to 450 rnm at room temperature from the thermally treated cerium-dioxide thin films on silicon. As a results of AES and HR-TEM measurement, it was confirmed that cerium silicates were generated by thermal treatment. These cerium silicates such as Ce4.667(SiO4)3O and Ce2Si2O7 are the source of the ultra-violet (UV) emission ranging from 358 nim to 450 nm (maximum at 388 rim).

Effect of the Heat Treatment on the Microstructure and Morphology of Cigs Thin Films Prepared by RF Magnetron Sputtering at Room Temperature

2020 ◽  
Vol 1012 ◽  
pp. 119-124
Author(s):  
Paulo Victor Nogueira da Costa ◽  
Rodrigo Amaral de Medeiro ◽  
Carlos Luiz Ferreira ◽  
Leila Rosa Cruz
Keyword(s):  
Thin Films ◽  
Heat Treatment ◽  
Magnetron Sputtering ◽  
Room Temperature ◽  
Morphological Changes ◽  
Film Surface ◽  
Rf Magnetron Sputtering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Glass Substrates

This work investigates the microstructural and morphological changes on CIGS thin films submitted to a post-deposition heat treatment. The CIGS 1000 nm-thick films were deposited at room temperature by RF magnetron sputtering onto glass substrates covered with molybdenum films. After deposition, the samples were submitted to a heat treatment, with temperatures ranging from 450 to 575 oC. The treatment was also carried out under a selenium atmosphere (selenization), from 400 to 500 oC. Morphological analyzes showed that the as-deposited film was uniform and amorphous. When the treatment was carried out without selenization, the crystallization occurred at or above 450 oC, and the grains remained nanosized. However, high temperatures led to the formation of discontinuities on the film surface and the formation of extra phases, as confirmed by X-ray diffraction data. The crystallization of the films treated under selenium atmosphere took place at lower temperatures. However, above 450 °C the film surface was discontinuous, with a lot of holes, whose amount increased with the temperature, showing that the selenization process was very aggressive. X-ray diffraction analyses showed that the extra phases were eliminated during selenization and the films had a preferential orientation along [112] direction. The results indicate that in the manufacturing process of solar cells, CIGS films deposited at room temperature should be submitted to a heat treatment carried out at 450 °C (without selenization) or 400 °C (with selenization).

Characterization of Rutile N-Doped TiO2 Films Prepared by RF Magnetron Sputtering

2013 ◽  
Vol 543 ◽  
pp. 277-280
Author(s):  
Marius Dobromir ◽  
Alina Vasilica Manole ◽  
Simina Rebegea ◽  
Radu Apetrei ◽  
Maria Neagu ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Photoelectron Spectroscopy ◽  
Room Temperature ◽  
Rf Magnetron Sputtering ◽  
Rutile Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Deposited Films

Rutile N-doped TiO2thin films were grown by RF magnetron sputtering on amorphous and crystalline substrates at room temperature. The surface elemental analysis, investigated by X-ray photoelectron spectroscopy indicated that the nitrogen content of the films could be adjusted up to values as high as 4.1 at.%. As demonstrated by the X-ray diffraction data, the as-deposited films (100 200 nm thick) showed no detectable crystalline structure, while after successive annealing in air for one hour at 400°C, 500°C and 600°C, the (110) rutile peaks occurred gradually as dominant features. The rutile phase in the films was confirmed by the band gap values of the deposited materials, which stabilized at 3.1 eV, for the thin films having 200 nm thicknesses.

Structure and Conductivity of Iodine-Doped C60 Thin Films

1994 ◽  
Vol 359 ◽  
Author(s):  
Jun Chen ◽  
Haiyan Zhang ◽  
Baoqiong Chen ◽  
Shaoqi Peng ◽  
Ning Ke ◽  
...  
Keyword(s):  
Thin Films ◽  
Electrical Conductivity ◽  
Room Temperature ◽  
Conductivity Measurements ◽  
X Ray Diffraction ◽  
Temperature Conductivity ◽  
Room Temperature Conductivity ◽  
X Ray ◽  
Thermally Activated ◽  
Order Of Magnitude

ABSTRACTWe report here the results of our study on the properties of iodine-doped C60 thin films by IR and optical absorption, X-ray diffraction, and electrical conductivity measurements. The results show that there is no apparent structural change in the iodine-doped samples at room temperature in comparison with that of the undoped films. However, in the electrical conductivity measurements, an increase of more that one order of magnitude in the room temperature conductivity has been observed in the iodine-doped samples. In addition, while the conductivity of the undoped films shows thermally activated temperature dependence, the conductivity of the iodine-doped films was found to be constant over a fairly wide temperature range (from 20°C to 70°C) exhibiting a metallic feature.

Substrate Temperature and La0.9Sr0.1Ga0.8Mg0.2O3-δ Electrolyte Film Growth by Radio Frequency Magnetron Sputtering

2015 ◽  
Vol 833 ◽  
pp. 127-133
Author(s):  
Jie Yu ◽  
Jie Xing ◽  
Xiu Hua Chen ◽  
Wen Hui Ma ◽  
Rui Li ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Substrate Temperature ◽  
Radio Frequency ◽  
Film Growth ◽  
Rf Magnetron Sputtering ◽  
X Ray Diffraction ◽  
X Ray ◽  
Electrolyte Film ◽  
Porous Anode

La0.9Sr0.1Ga0.8Mg0.2O3-δ (LSGM) electrolyte thin films were fabricated on La0.7Sr0.3Cr0.5Mn0.5O2.75 (LSCM) porous anode substrates by Radio Frequency (RF) magnetron sputtering method. The compatibility between LSGM and LSCM was examined. Microstructures of LSGM thin films fabricated were observed by scanning electron microscope (SEM). The effect of substrate temperature on LSGM thin films was clarified by X-ray Diffraction (XRD). Deposition rate increases firstly at the range of 50°C~150°C, and then decreases at the range of 150°C ~300°C. After annealing, perovskite structure with the same growth orientation forms at different substrate temperature. Crystallite size decreases at first, to the minimum point at 150°C, then increases as substrate temperature rises.

Synthesis of CaWO4:(Eu3+,Tb3+) Thin Films by a Two-Step Method at Room Temperature

2013 ◽  
Vol 710 ◽  
pp. 170-173
Author(s):  
Lian Ping Chen ◽  
Yuan Hong Gao
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Phase Composition ◽  
Room Temperature ◽  
Electrochemical Techniques ◽  
Luminescent Properties ◽  
X Ray Diffraction ◽  
Step Method ◽  
X Ray ◽  
Rare Earth Doped

It is hardly possible to obtain rare earth doped CaWO4thin films directly through electrochemical techniques. A two-step method has been proposed to synthesize CaWO4:(Eu3+,Tb3+) thin films at room temperature. X-ray diffraction, energy dispersive X-ray analysis, spectrophotometer were used to characterize their phase, composition and luminescent properties. Results reveal that (Eu3+,Tb3+)-doped CaWO4films have a tetragonal phase. When the ratio of n (Eu)/n (Tb) in the solution is up to 3:1, CaWO4:(Eu3+,Tb3+) thin film will be enriched with Tb element; on the contrary, when the ratio in the solution is lower than 1:4, CaWO4:(Eu3+,Tb3+) thin film will be enriched with Eu element. Under the excitation of 242 nm, sharp emission peaks at 612, 543, 489 and 589 nm have been observed for CaWO4:(Eu3+,Tb3+) thin films.

Study of Photoluminescence Properties of CuxO Thin Films Prepared by Reactive Radio Frequency Magnetron Sputtering

2015 ◽  
Vol 1792 ◽  
Author(s):  
Jiantuo Gan ◽  
Augustinas Galeckas ◽  
Vishnukanthan Venkatachalapathy ◽  
Heine N. Riise ◽  
Bengt G. Svensson ◽  
...  
Keyword(s):  
Thin Films ◽  
Magnetron Sputtering ◽  
Radio Frequency ◽  
Room Temperature ◽  
Quartz Substrate ◽  
Rf Magnetron Sputtering ◽  
Considerable Improvement ◽  
Photoluminescence Properties ◽  
Radio Frequency Magnetron Sputtering ◽  
Room Temperature Photoluminescence

ABSTRACTCuxO thin films have been deposited on a quartz substrate by reactive radio frequency (rf) magnetron sputtering at different target powers Pt (140-190 W) while keeping other growth process parameters fixed. Room-temperature photoluminescence (PL) measurements indicate considerable improvement of crystallinity for the films deposited at Pt>170 W, with most pronounced excitonic features being observed in the film grown using Pt=190 W. These results corroborate well with the surface morphology of the films, which was found more flat, smooth and homogeneous for Pt >170 W films in comparison with those deposited at lower powers.

Long-term Room Temperature Instability in Thermal Conductivity of InGaZnO Thin Films

MRS Advances ◽  
2016 ◽  
Vol 1 (22) ◽  
pp. 1631-1636 ◽  
Author(s):  
Boya Cui ◽  
D. Bruce Buchholz ◽  
Li Zeng ◽  
Michael Bedzyk ◽  
Robert P. H. Chang ◽  
...  
Keyword(s):  
Thin Films ◽  
Thermal Conductivity ◽  
Room Temperature ◽  
Storage Time ◽  
Laser Deposition ◽  
Low Oxygen ◽  
X Ray Diffraction ◽  
3Ω Method ◽  
X Ray

ABSTRACTThe cross-plane thermal conductivities of InGaZnO (IGZO) thin films in different morphologies were measured on three occasions within 19 months, using the 3ω method at room temperature 300 K. Amorphous (a-), semi-crystalline (semi-c-) and crystalline (c-) IGZO films were grown by pulsed laser deposition (PLD), followed by X-ray diffraction (XRD) for evaluation of film quality and crystallinity. Semi-c-IGZO shows the highest thermal conductivity, even higher than the most ordered crystal-like phase. After being stored in dry low-oxygen environment for months, a drastic decrease of semi-c-IGZO thermal conductivity was observed, while the thermal conductivity slightly reduced in c-IGZO and remained unchanged in a-IGZO. This change in thermal conductivity with storage time can be attributed to film structural relaxation and vacancy diffusion to grain boundaries.

Sign in / Sign up

Export Citation Format

Share Document