A New Method to Increase the Magnetoelectric Voltage Coefficients of Metglas/PVDF Laminate Composites

2009 ◽  
Vol 1199 ◽  
Author(s):  
Zhao Fang ◽  
David Sheng-Guo Lu ◽  
Ninad Mokhariwale ◽  
Mario Remond El Tahchi ◽  
Qiming Zhang
Keyword(s):  
Magnetic Field ◽  
Aspect Ratio ◽  
Magnetic Flux ◽  
Polyvinylidene Fluoride ◽  
Effective Means ◽  
Concentration Effect ◽  
Magnetic Flux Density ◽  
Laminar Composites ◽  
Voltage Coefficient ◽  
Flux Concentration

AbstractThe magnetic flux density inside a Metglas sheet is much higher than that of the applied external magnetic field due to its high magnetic permeability, which is known as the magnetic flux concentration effect. Magnetic flux concentration of Metglas as a function of its sheet aspect ratio (width/length) was investigated for Metglas/Polyvinylidene fluoride (PVDF) laminar composites. Both the simulations and experimental results suggest that the magnetic flux concentration effect is markedly enhanced when the aspect ratio of a Metglas sheet is reduced. Consequently the magnetostriction of Metglas and the magnetoelectric (ME) voltage coefficients of the laminar composites are enhanced. The ME voltage coefficient for a laminar composite with a 1 mm wide and 30 mm long Metglas sheet (25 μm thick) is 21.46 V/cm•Oe, which is much higher than those reported earlier in similar laminar composites without making use of the flux concentration effect. The results demonstrate an effective means to significantly enhance the sensitivity of the magnetostrictive/piezoelectric composites as weak magnetic field sensors.

scholarly journals Design of a New 1D Halbach Magnet Array with Good Sinusoidal Magnetic Field by Analyzing the Curved Surface

Sensors ◽  
2021 ◽  
Vol 21 (7) ◽  
pp. 2522
Author(s):  
Guangdou Liu ◽  
Shiqin Hou ◽  
Xingping Xu ◽  
Wensheng Xiao
Keyword(s):  
Magnetic Field ◽  
Magnetic Flux ◽  
Permanent Magnet ◽  
Flux Density ◽  
Permanent Magnets ◽  
Air Gap ◽  
Curved Surface ◽  
Magnetic Flux Density ◽  
Sinusoidal Magnetic Field ◽  
The Magnetic Field

In the linear and planar motors, the 1D Halbach magnet array is extensively used. The sinusoidal property of the magnetic field deteriorates by analyzing the magnetic field at a small air gap. Therefore, a new 1D Halbach magnet array is proposed, in which the permanent magnet with a curved surface is applied. Based on the superposition of principle and Fourier series, the magnetic flux density distribution is derived. The optimized curved surface is obtained and fitted by a polynomial. The sinusoidal magnetic field is verified by comparing it with the magnetic flux density of the finite element model. Through the analysis of different dimensions of the permanent magnet array, the optimization result has good applicability. The force ripple can be significantly reduced by the new magnet array. The effect on the mass and air gap is investigated compared with a conventional magnet array with rectangular permanent magnets. In conclusion, the new magnet array design has the scalability to be extended to various sizes of motor and is especially suitable for small air gap applications.

Effects of External Transverse Alternating Magnetic Field on the Oscillating Amplitude of Atmospheric Pressure Plasma Arc

2010 ◽  
Vol 129-131 ◽  
pp. 692-696
Author(s):  
Jian Bing Meng ◽  
Xiao Juan Dong ◽  
Chang Ning Ma
Keyword(s):  
Magnetic Field ◽  
Magnetic Flux ◽  
Flux Density ◽  
Flow Rate ◽  
Gas Flow ◽  
Atmospheric Pressure Plasma ◽  
Alternating Magnetic Field ◽  
Magnetic Flux Density ◽  
Plasma Arc ◽  
Arc Current

A mathematical model was developed to describe the oscillating amplitude of the plasma arc injected transverse to an external transverse alternating magnetic field. The characteristic of plasma arc under the external transverse alternating magnetic field imposed perpendicular to the plasma current was discussed. The effect of processing parameters, such as flow rate of working gas, arc current, magnetic flux density and the standoff from the nozzle to the workpiece, on the oscillation of plasma arc were also analyzed. The results show that it is feasible to adjust the shape of the plasma arc by the transverse alternating magnetic field, which expands the region of plasma arc thermal treatment upon the workpiece. Furthermore, the oscillating amplitude of plasma arc decreases with decrease of the magnetic flux density. Under the same magnetic flux density, more gas flow rate, more arc current, and less standoff cause the oscillating amplitude to decrease. The researches have provided a deeper understanding of adjusting of plasma arc characteristics.

scholarly journals Near-axis expansion of stellarator equilibrium at arbitrary order in the distance to the axis

2020 ◽  
Vol 86 (1) ◽  
Author(s):  
R. Jorge ◽  
W. Sengupta ◽  
M. Landreman
Keyword(s):  
Magnetic Field ◽  
Aspect Ratio ◽  
Magnetic Flux ◽  
Arbitrary Order ◽  
Analytical Framework ◽  
Field Vector ◽  
Magnetic Axis ◽  
Direct Construction ◽  
Geometrical Properties ◽  
Rotational Transform

A direct construction of equilibrium magnetic fields with toroidal topology at arbitrary order in the distance from the magnetic axis is carried out, yielding an analytical framework able to explore the landscape of possible magnetic flux surfaces in the vicinity of the axis. This framework can provide meaningful analytical insight into the character of high-aspect-ratio stellarator shapes, such as the dependence of the rotational transform and the plasma beta limit on geometrical properties of the resulting flux surfaces. The approach developed here is based on an asymptotic expansion on the inverse aspect ratio of the ideal magnetohydrodynamics equation. The analysis is simplified by using an orthogonal coordinate system relative to the Frenet–Serret frame at the magnetic axis. The magnetic field vector, the toroidal magnetic flux, the current density, the field line label and the rotational transform are derived at arbitrary order in the expansion parameter. Moreover, a comparison with a near-axis expansion formalism employing an inverse coordinate method based on Boozer coordinates (the so-called Garren–Boozer construction) is made, where both methods are shown to agree at lowest order. Finally, as a practical example, a numerical solution using a W7-X equilibrium is presented, and a comparison between the lowest-order solution and the W7-X magnetic field is performed.

scholarly journals FFC NMR Relaxometer with Magnetic Flux Density Control

2019 ◽  
Vol 9 (3) ◽  
pp. 22
Author(s):  
António Roque ◽  
Duarte M. Sousa ◽  
Pedro Sebastião ◽  
Elmano Margato ◽  
Gil Marques
Keyword(s):  
Magnetic Field ◽  
Magnetic Flux ◽  
Flux Density ◽  
Low Cost ◽  
Current Control ◽  
Magnetic Flux Density ◽  
Density Control ◽  
Earth Magnetic Field ◽  
Innovative Solution ◽  
Field Cycling

This paper describes an innovative solution for the power supply of a fast field cycling (FFC) nuclear magnetic resonance (NMR) spectrometer considering its low power consumption, portability and low cost. In FFC cores, the magnetic flux density must be controlled in order to perform magnetic flux density cycles with short transients, while maintaining the magnetic flux density levels with high accuracy and homogeneity. Typical solutions in the FFC NMR literature use current control to get the required magnetic flux density cycles, which correspond to an indirect magnetic flux density control. The main feature of this new relaxometer is the direct control of the magnetic flux density instead of the magnet current, in contrast with other equipment available in the market. This feature is a great progress because it improves the performance. With this solution it is possible to compensate magnetic field disturbances and parasitic magnetic fields guaranteeing, among other possibilities, a field control below the earth magnetic field. Experimental results validating the developed solution and illustrating the real operation of this type of equipment are shown.

PDMS Membrane Microactuator for Focal Tunable Microlens

2006 ◽  
Author(s):  
Seok Woo Lee ◽  
Seung S. Lee
Keyword(s):  
Magnetic Field ◽  
Magnetic Flux ◽  
Flux Density ◽  
Lorentz Force ◽  
Spin Coating ◽  
Large Displacement ◽  
Pdms Membrane ◽  
Magnetic Flux Density ◽  
Optical Performance ◽  
Electrical Components

In this paper, PDMS membrane for a large displacement is fabricated by new fabrication process which can be integrated with electrical components on substrates fabricated by conventional microfabrication processes and the performance of the membrane using electromagnetism was evaluated. Rectangular PDMS membranes are designed as 2mm and 3mm in width, respectively and are actuated by Lorentz force induced by current paths spread on the membrane. The PDMS membrane is fabricated by reducing a viscosity of uncured PDMS with dilution and spin coating on the substrate on which electric components generating Lorentz force. Finally, PDMS membrane including electric components is opened by a bulk micromachining. The device is tested in magnetic field induced by Nd-Fe-B magnet whose magnetic flux density is 90G. When applied currents are 20, 25, and 30mA, the maximum deflections of membranes are 1.21, 3.07, and 20.2μm for 1.5mm width membrane and 3.34, 31.0, and 50.9μm for width 3mm membrane, respectively. The large displacement PDMS membrane actuator has potentially various applications such as fluidics, optics, acoustics, and electronics. Currently, we are planning to measure the optical performance of the actuator as a focal tunable liquid lens.

Platform Design for Characterizing Shear Force Produced by Magnetized Magnetorheological Fluid

2019 ◽  
Author(s):  
Ping-Hsun Lee ◽  
Jen-Yuan (James) Chang
Keyword(s):  
Magnetic Field ◽  
Magnetic Flux ◽  
Yield Stress ◽  
Flux Density ◽  
Shear Force ◽  
Permanent Magnets ◽  
Magnetic Flux Density ◽  
Finite Element Method Result ◽  
Mr Fluid ◽  
The Magnetic Field

Abstract In this paper we proposed a platform for measuring shear force of magnetorheological (MR) fluid by which the relationship of yield stress and magnetic flux density of specific material can be determined. The device consisted of a rotatable center tube in a frame body and the magnetic field was provided by two blocks of permanent magnets placed oppositely outside the frame body. The magnitude and direction of the magnetic field were manipulated by changing the distance of the two permanent magnets from the frame body and rotating the center tube, respectively. For determining the magnetic field of the device, we adopted an effective method by fitting the FEM (finite element method) result to the measured one and then rebuilt the absent components to approximate the magnetic field, which was hardly to be measured simultaneously as different device setup were required. With the proposed platform and analytical methods, the drawing shear force and the corresponding yield stress contributed by MR fluid could be evaluated in respect to the magnitude and direction of given magnetic flux density with acceptable accuracy for specific designing purposes without a large, complex, and expensive instrument.

Effect of distribution of magnetic flux density on purifying liquid metal by travelling magnetic field

1999 ◽  
Vol 3 (2) ◽  
pp. 157-161 ◽  
Author(s):  
Yunbo Zhong ◽  
Zhongming Ren ◽  
Kang Deng ◽  
Guochang Jiang ◽  
Kuangdi Xu
Keyword(s):  
Magnetic Field ◽  
Liquid Metal ◽  
Magnetic Flux ◽  
Flux Density ◽  
Magnetic Flux Density

A High Accuracy of Magnetometer by Using Independent Directional Magnetic Field Measurement Technique

2014 ◽  
Vol 565 ◽  
pp. 133-137
Author(s):  
Athirot Mano ◽  
Wisut Titiroongruang
Keyword(s):  
Magnetic Field ◽  
Magnetic Flux ◽  
Flux Density ◽  
Measurement Technique ◽  
Field Measurement ◽  
High Accuracy ◽  
Two Dimensions ◽  
Magnetic Flux Density ◽  
Magnetic Field Measurement ◽  
Hall Sensors

In a measurement of magnetic flux density with high accuracy by using Hall effect sensor must be considered position of Hall sensor, that perfect perpendicular with magnetic flux line for measurement. Only one Hall element can cause measuring error. Therefore, this paper presents an application of independent directional magnetic field measurement technique on two dimensions for high accuracy magnetometer. It is presented by using two Hall sensors locate perpendicular to each other and use the relation of the two voltage output signal from both Hall sensors to calculate constant Hall voltage and Magnetic flux density with high accuracy by using trigonometric function with Lab-View programming. And as the result of experiment, this technique can reduce the limitation in term of this angle in the range magnetic flux density can be measured 0-1800 gauss. A calibration curve of this system compare with standard Gauss meter shows the coefficient of determination (R2) equal to 1 and has the accuracy percentage as less than 0.5%.

Transport of Magnetic Particles Under a Uniform Magnetic Field in Microchannels

2013 ◽  
Author(s):  
Gui-Ping Zhu ◽  
Nam-Trung Nguyen
Keyword(s):  
Magnetic Field ◽  
Field Strength ◽  
Magnetic Flux ◽  
Flux Density ◽  
Uniform Magnetic Field ◽  
Magnetic Particles ◽  
Independent Solution ◽  
Magnetic Flux Density ◽  
Mixing Efficiency ◽  
Water Mixture

This paper reports the numerical and experimental investigation on magnetic particle concentration in a uniform magnetic field. The flow system consists of water-based ferrofluid and glycerol/DI water mixture streams. Two regimes were observed with spreading and mixing phenomena. With a low magnetic field strength, the spread of magnetic particles is caused by improved diffusion migration. With a relatively high field strength, instability at the interface would occur due to the mismatch in magnetization of the fluid streams. The transport of magnetic particles is induced by chaotic mixing of the fluids caused by a secondary flow. The mixing phenomena are characterized by magnetic flux density. For configuration with flow rate and viscosity ratio (between diamagnetic and magnetic streams) being set at 1 and 0.5, the mixing efficiency analyzed based on magnetic particles concentration increases approximately by 0.3 at around 3.5 mT. This value of magnetic flux density indicates the requirement on instability inception. The mixing efficiency increases with magnetic flux density increases further. Complete mixing can be achieved with a magnetic flux density at around 10 mT. The magnetic approach offers a wireless, heat-free and pH-independent solution for a lab-on-a-chip system.

Sign in / Sign up

Export Citation Format

Share Document