In-Based Ohmic Contacts to the Base Layer of GaAs-AlGaAs Heterojunction Bipolar Transistors

1990 ◽  
Vol 181 ◽  
Author(s):  
F. Ren ◽  
S. J. Pearton ◽  
W. S. Hobson ◽  
T. R. Fullowan ◽  
A. B. Emerson ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Heterojunction Bipolar Transistors ◽  
Ohmic Contacts ◽  
Bipolar Transistors ◽  
Base Layer ◽  
Specific Contact Resistance ◽  
Current Transport ◽  
Specific Contact ◽  
P Type

ABSTRACTThe use of AuBe-In/Ag/Au p-ohmic contacts for the base layer of GaAs-AIGaAs heterojunction bipolar transistors (HBTs) is described. Annealing at 420°C for 20 sec produces a contact resistivity of 0.095 Ω mm and a specific contact resistance of l.5 × 10-7 Ω cm2, and the surface morphology of the contact is excellent. The role of the silver is as a diffusion barrier to prevent Au spiking into the base layer which could degrade the HBT performance. The presence of the In layer is highly desirable in order to reduce the contact resistance, probably by forming an InGaAs phase at the metal-GaAs interface. Beryllium acts as the p-type dopant, and the top Au layer is used to lower the contact sheet resistance. Current transport through the structure is dominated by tunneling through the barrier due to field emission in the highly doped base layer at p-type doping levels above ∼1019 cm−3

Improvement of the Specific Contact Resistance on P-Type 4H-SiC by Using a Highly P-Typed Doped 4H-SiC Layer Selectively Grown by VLS Transport

2014 ◽  
Vol 806 ◽  
pp. 57-60
Author(s):  
Nicolas Thierry-Jebali ◽  
Arthur Vo-Ha ◽  
Davy Carole ◽  
Mihai Lazar ◽  
Gabriel Ferro ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Schottky Barrier Height ◽  
Annealing Temperature ◽  
Process Condition ◽  
Specific Contact Resistance ◽  
High Doping Level ◽  
Annealing Temperatures ◽  
Specific Contact ◽  
P Type

This work reports on the improvement of ohmic contacts made on heavily p-type doped 4H-SiC epitaxial layer selectively grown by Vapor-Liquid-Solid (VLS) transport. Even before any annealing process, the contact is ohmic. This behavior can be explained by the high doping level of the VLS layer (Al concentration > 1020 cm-3) as characterized by SIMS profiling. Upon variation of annealing temperatures, a minimum value of the Specific Contact Resistance (SCR) down to 1.3x10-6 Ω.cm2 has been obtained for both 500 °C and 800 °C annealing temperature. However, a large variation of the SCR was observed for a same process condition. This variation is mainly attributed to a variation of the Schottky Barrier Height.

Current Transport in Ti/Al/Ni/Au Ohmic Contacts to GaN and AlGaN

2007 ◽  
Vol 556-557 ◽  
pp. 1027-1030 ◽  
Author(s):  
Ferdinando Iucolano ◽  
Fabrizio Roccaforte ◽  
Filippo Giannazzo ◽  
A. Alberti ◽  
Vito Raineri
Keyword(s):  
Contact Resistance ◽  
Field Emission ◽  
Ohmic Contacts ◽  
Theoretical Models ◽  
Specific Contact Resistance ◽  
Strong Increase ◽  
Current Transport ◽  
Electrical Characteristics ◽  
Structural And Electrical Properties ◽  
Specific Contact

In this work, the structural and electrical properties of Ti/Al/Ni/Au contacts on n-type Gallium Nitride were studied. An ohmic behaviour was observed after annealing above 700°C. The structural analysis showed the formation of an interfacial TiN layer and different phases in the reacted layer (AlNi, AlAu4, Al2Au) upon annealing. The temperature dependence of the specific contact resistance demonstrated that the current transport occurs through thermoionic field emission in the contacts annealed at 600°C, and field emission after annealing at higher temperatures. By fitting the data with theoretical models, a reduction of the Schottky barrier from 1.21eV after annealing at 600°C to 0.81eV at 800°C was demonstrated, together with a strong increase of the carrier concentration at the interface. The reduction of the contact resistance upon annealing was discussed by correlating the structural and electrical characteristics of the contacts.

Ohmic Contacts to p-Type InGaAs/InP with a Graded Bandgap Heterobarrier

1993 ◽  
Vol 318 ◽  
Author(s):  
Patrick W. Leech ◽  
Geoffrey K. Reeves
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Rutherford Backscattering Spectrometry ◽  
Specific Contact Resistance ◽  
Superlattice Structure ◽  
Specific Contact ◽  
P Type ◽  
Metal Layers ◽  
Anneal Temperature ◽  
Graded Bandgap

ABSTRACTOhmic contacts to p-type InP with an In0.47Ga0.53As buffer layer and an interposed superlattice of 50 Å In0.47Ga0.53As/ 50 Å InP have been investigated. Initial studies of contacts to In0.47Ga0.53As/ InP without the superlattice structure have shown that Pd/Zn/Pd/Au metallization produced a lower specific contact resistance (pc = 1.1 × 10−4 Ω cm2) than Pd/Ge/Au, and over a wider range of anneal temperature than Au/Zn/Au. The incorporation of the superlattice in the p-In0.47Ga0.53As/ InP structure resulted in Pd/Zn/Pd/Au contacts with pc of 3.2 × 10−5 Ω cm2 as-deposited and 7.5 × 10−6 Ω.cm2 after a 500 °C anneal. The presence of Pd/Zn in the metallization was shown as important in reducing pc. Significant intermixing of the metal layers and In0.47Ga0.53As occured at ≥ 350 °C, as revealed by Rutherford backscattering spectrometry.

Ni-Al-Ti Ohmic Contacts with Preserved Form Factor and Few 10- 4 Ωcm2 Specific Resistance on 0.1-1 Ωcm p-Type 4H-SiC

2018 ◽  
Vol 924 ◽  
pp. 385-388 ◽  
Author(s):  
Roberta Nipoti ◽  
Maurizio Puzzanghera ◽  
Maria Concetta Canino ◽  
Giovanna Sozzi ◽  
Paolo Fedeli
Keyword(s):  
Form Factor ◽  
Contact Resistance ◽  
Contact Area ◽  
Room Temperature ◽  
Ohmic Contacts ◽  
Specific Resistance ◽  
Thickness Ratio ◽  
Specific Contact Resistance ◽  
Specific Contact ◽  
P Type

This study shows that a thin Ni film on Al/Ti/4H-SiC metal pads allows to preserve the pad form factor during a 1000 °C/2 min treatment, provided that the Al and Ti film thicknesses are sufficiently thin. Moreover, by reducing the Al to Ti thickness ratio, droplet formation in the contact area is avoided and a mirror-like appearance is obtained. This optimal contact morphology corresponds to a specific contact resistance of few 10-4Ωcm2at room temperature on p-type 4H-SiC with resistivity in the range 0.1 – 1 Ωcm.

Al/Ni And Al/Ti Ohmic Contact To P-type SiC Diffused Layer

2000 ◽  
Vol 640 ◽  
Author(s):  
Xaiobin Wang ◽  
Stanislav Soloviev ◽  
Ying Gao ◽  
G. Straty ◽  
Tangali Sudarshan ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Specific Contact Resistance ◽  
Metal Contacts ◽  
Transfer Length ◽  
Type Layer ◽  
Transmission Line Method ◽  
Specific Contact ◽  
Background Doping ◽  
P Type

ABSTRACTOhmic contacts to p-type SiC were fabricated by depositing Al/Ni and Al/Ti followed by high temperature annealing. A p-type layer was fabricated by Al or B diffusion from vapor phase into both p-type and n-type substrates. The thickness of the diffused layer was about 0.1–0.2 μm with surface carrier concentration of about 1.0×1019cm−3. Metal contacts to a p-type substrate with a background doping concentration of 1.2×1018cm−3, without a diffusion layer, were also formed. The values of specific contact resistance obtained by Circular Transmission Line Method (CTLM) and Transfer Length Method (TLM) for the n-type substrate, and by Cox & Strack method for p-type substrate, respectively, varied from 1.3×10−4Ωcm2 to 8.8×10−3 Ωcm2. The results indicate that the specific contact resistance could be significantly reduced by creating a highly doped diffused surface layer.

scholarly journals Comparison of Electrical Properties of Ohmic Contact Realized on p-Type 4H-SiC

2008 ◽  
Vol 600-603 ◽  
pp. 639-642
Author(s):  
Duy Minh Nguyen ◽  
Christophe Raynaud ◽  
Mihai Lazar ◽  
Heu Vang ◽  
Dominique Planson
Keyword(s):  
Surface Roughness ◽  
Electrical Properties ◽  
Contact Resistance ◽  
Carrier Mobility ◽  
Ohmic Contacts ◽  
Series Resistance ◽  
Specific Contact Resistance ◽  
Specific Contact ◽  
P Type ◽  
Post Implantation

N+ 4H-SiC commercial substrates with n-type epilayers have been used to realize bipolar diodes and TLM structures. The p-type emitter of diodes was realized by Al implantations followed by a post-implantation annealing with or without a graphite capping layer. Ohmic contacts were formed by depositing Ti/Ni on the backside and Ni/Al on the topside of the wafer. It appears that capping the sample during the annealing reduces considerably the surface roughness and the specific contact resistance. Sheet resistance and specific contact resistance as low as 2kΩ/□ and respectively 1.75×10-4 Ωcm² at 300 K have been obtained. I-V measurements as a function of temperature have been performed from ~100 to ~500 K. The variations of the series resistance vs. temperature can be explained by the freeze-out of carriers and by the variation of carrier mobility.

Dual Role of Tin Reaction Barrier in Gold-Based Metallization to GaAs

1993 ◽  
Vol 300 ◽  
Author(s):  
A. Piotrowska ◽  
E. Kaminska ◽  
M. Guziewicz ◽  
S. Kwiatkowski ◽  
A. Turos
Keyword(s):  
Magnetron Sputtering ◽  
Contact Resistance ◽  
Ohmic Contact ◽  
Diffusion Barrier ◽  
Ohmic Contacts ◽  
Specific Contact Resistance ◽  
Tin Films ◽  
Specific Contact ◽  
Tin Diffusion Barrier

ABSTRACTThe formation of ohmic contacts to p-GaAs based on Au-Zn system comprising a TiN diffusion barrier has been investigated using 2 MeV He+ RBS and the specific contact resistance measurements. It has been proved that TiN films deposited by reactive RF bias magnetron sputtering serves two purposes. First it suppresses the arsenic evaporation and thus confines the reaction between AuZn and GaAs. Second, it prevents intermixing between p-GaAs/Au(Zn) ohmic contact and an overlayer of Au.

scholarly journals Applications of Vapor-Liquid-Solid Selective Epitaxy of Highly p-Type Doped 4H-SiC: PiN Diodes with Peripheral Protection and Improvement of Specific Contact Resistance of Ohmic Contacts

2014 ◽  
Vol 778-780 ◽  
pp. 639-644 ◽  
Author(s):  
Nicolas Thierry-Jebali ◽  
Mihai Lazar ◽  
Arthur Vo-Ha ◽  
Davy Carole ◽  
Véronique Soulière ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Specific Contact Resistance ◽  
Vapor Liquid Solid ◽  
Pin Diodes ◽  
High Doping Level ◽  
Selective Epitaxial Growth ◽  
Specific Contact ◽  
P Type ◽  
Vapor Liquid

This work deals with two applications of the Selective Epitaxial Growth of highly p-type doped buried 4H-SiC in Vapor-Liquid-Solid configuration (SEG-VLS). The first application is the improvement of the Specific Contact Resistance (SCR) of contacts made on such p-type material. As a result of the extremely high doping level, SCR values as low as 1.3x10-6Ω.cm2have been demonstrated. Additionally, the high Al concentration of the SEG-VLS 4H-SiC material induces a lowering of the Al acceptor ionization energy down to 40 meV. The second application is the fabrication of PiN diodes with SEG-VLS emitter and guard-rings peripheral protection. Influence of some process parameters and crystal orientation on the forward and reverse characteristics of the PiN diodes is discussed.

Low-Resistance Electrical Contacts to p-Type GaN by Using InxGa1-xN Cap Layers

2001 ◽  
Vol 693 ◽  
Author(s):  
Th. Gessmann ◽  
Y.-L. Li ◽  
J. W. Graff ◽  
E. F. Schubert ◽  
J. K. Sheu
Keyword(s):  
Contact Resistance ◽  
Electric Fields ◽  
Ohmic Contacts ◽  
Electrical Contacts ◽  
Specific Contact Resistance ◽  
Low Resistance ◽  
Transmission Line Method ◽  
Specific Contact ◽  
P Type ◽  
20 Nm

AbstractA novel type of low-resistance ohmic contacts is demonstrated utilizing polarization-induced electric fields in thin p-type InGaN layers on p-type GaN. An increase of the hole tunneling probability through the barrier and a concomitant significant decrease of the specific contact resistance can be attributed to a reduction of the tunneling barrier width in the InGaN capping layers due to the polarization-induced electric fields. The specific contact resistance of Ni (10 nm) / Au (30 nm) contacts deposited on the InGaN capping layers was determined by the transmission line method. Specific contact resistances of 1.2 × 10-2 Ω cm2 and 6 × 10-3 & cm2 were obtained for capping layer thicknesses of 20 nm and 2 nm, respectively.

Formation of Ni/Pt/Au Ohmic Contacts to p-GaN

1997 ◽  
Vol 482 ◽  
Author(s):  
Ja-Soon Jang ◽  
Hyo-Gun Kim ◽  
Kyung-Hyun Park ◽  
Chang-Sub Um ◽  
Il-Ki Han ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contact ◽  
Ohmic Contacts ◽  
Chemical Vapor ◽  
Electron Beam Evaporation ◽  
Specific Contact Resistance ◽  
Metal Thin Films ◽  
Linear Behavior ◽  
Specific Contact ◽  
P Type

AbstractWe report a new Ni/Pt/Au (20/30/80 nm) metallization scheme to achieve a low ohmic contacts to p-type GaN with a carrier concentration of 9.4 × 1016 cm-3. A Mg-doped GaN layer (0.5 μm) was grown on (0001) sapphire substrate by metalorganic chemical vapor deposition (MOCVD). All metal thin films were deposited on the p-GaN layer in an electron-beam evaporation system. Samples were annealed by a rapid thermal annealing (RTA) process at a range of temperatures from 300 °C to 850 °C under a flowing Ar atmosphere. A circulartransmission line model (c-TLM) was employed to calculate the specific contact resistance, and current-voltage (I-V) data were measured with HP4155A. The Ni/Pt/Au contacts without the annealing process showed nearly rectifying characteristics. The ohmic contacts were formed on the samples annealed at 500 °C for 30 sec and the I-V data showed a linear behavior. The specific contact resistance was 2.1 × 10-2 Ωcm2. However with increasing the annealing temperature above 600 °C, ohmic contacts were again degraded. Auger electron spectroscopy (AES) depth profiles were used to investigate the interfacial reactions between the trilayer and GaN. AES results suggested that Pt plays a significant role in forming ohmic contact as an acceptor at the interface. Atomic force microscope (AFM) also showed that the samples with good ohmic contact have very smooth surface.

Sign in / Sign up

Export Citation Format

Share Document